Datasheet.kr   

74HC4066 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 74HC4066은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 74HC4066 자료 제공

부품번호 74HC4066 기능
기능 Quad single-pole single-throw analog switch
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


74HC4066 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 24 페이지수

미리보기를 사용할 수 없습니다

74HC4066 데이터시트, 핀배열, 회로
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
Rev. 8 — 3 December 2015
Product data sheet
1. General description
The 74HC4066; 74HCT4066 is a quad single pole, single throw analog switch. Each
switch features two input/output terminals (nY and nZ) and an active HIGH enable input
(nE). When nE is LOW, the analog switch is turned off. Inputs include clamp diodes. This
enables the use of current limiting resistors to interface inputs to voltages in excess of
VCC.
2. Features and benefits
Input levels nE inputs:
For 74HC4066: CMOS level
For 74HCT4066: TTL level
Low ON resistance:
50 (typical) at VCC = 4.5 V
45 (typical) at VCC = 6.0 V
35 (typical) at VCC = 9.0 V
Specified in compliance with JEDEC standard no. 7A
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
Multiple package options
Specified from 40 C to +85 C and 40 C to +125 C




74HC4066 pdf, 반도체, 판매, 대치품
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
7. Limiting values
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min Max Unit
VCC
IIK
ISK
ISW
ICC
IGND
Tstg
Ptot
supply voltage
input clamping current
switch clamping current
switch current
supply current
ground current
storage temperature
total power dissipation
VI < 0.5 V or VI > VCC + 0.5 V
VSW < 0.5 V or VSW > VCC + 0.5 V
VSW = 0.5 V to VCC + 0.5 V
Tamb = 40 C to +125 C
SO14, (T)SSOP14 and DHVQFN14
packages
0.5
-
-
[1] -
-
-
65
[2]
-
+11.0
20
20
25
50
50
+150
V
mA
mA
mA
mA
mA
C
500 mW
P power dissipation
per switch
- 100 mW
[1] To avoid drawing VCC current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC current will flow out of terminals Yn. In this case there is
no limit for the voltage drop across the switch, but the voltages at Yn and Z may not exceed VCC or GND.
[2] For SO14 package: Ptot derates linearly with 8 mW/K above 70 C.
For (T)SSOP14 packages: Ptot derates linearly with 5.5 mW/K above 60 C.
For DHVQFN14 packages: Ptot derates linearly with 4.5 mW/K above 60 C.
8. Recommended operating conditions
Table 5. Recommended operating conditions
Symbol Parameter
Conditions
VCC
VI
VSW
Tamb
t/V
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise
and fall rate
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 10.0 V
74HC4066
Min Typ Max
2.0 5.0 10.0
GND
-
VCC
GND
-
VCC
40 +25 +125
- - 625
- 1.67 139
- - 83
- - 35
74HCT4066
Min Typ Max
4.5 5.0 5.5
GND
-
VCC
GND
-
VCC
40 +25 +125
---
- 1.67 139
---
---
Unit
V
V
V
C
ns/V
ns/V
ns/V
ns/V
74HC_HCT4066
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 3 December 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
4 of 24

4페이지










74HC4066 전자부품, 판매, 대치품
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
Table 7. Static characteristics 74HC4066 …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter
Conditions
ICC supply current
CI input capacitance
Csw switch capacitance
Tamb = 40 C to +125 C
VIH HIGH-level input voltage
VIL LOW-level input voltage
II input leakage current
IS(OFF)
OFF-state leakage current
VI = VCC or GND; Vis = GND or VCC;
Vos = VCC or GND
VCC = 6.0 V
VCC = 10.0 V
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 9.0 V
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 9.0 V
VI = VCC or GND
VCC = 6.0 V
VCC = 10.0 V
VCC = 10.0 V; VI = VIH or VIL;
VSW= VCC GND; see Figure 8
per channel
IS(ON)
ICC
ON-state leakage current
supply current
VCC = 10.0 V; VI = VIH or VIL;
VSW= VCC GND; see Figure 9
VI = VCC or GND; Vis = GND or VCC;
Vos = VCC or GND
VCC = 6.0 V
VCC = 10.0 V
[1] Typical values are measured at Tamb = 25 C.
Min Typ[1] Max Unit
- - 20.0 A
- - 40.0 A
- 3.5 - pF
- 8 - pF
1.5 -
-V
3.15 -
-V
4.2 -
-V
6.3 -
-V
- - 0.50 V
- - 1.35 V
- - 1.80 V
- - 2.70 V
- - 1.0 A
- - 2.0 A
- - 1.0 A
- - 1.0 A
- - 40 A
- - 80 A
Table 8. Static characteristics 74HCT4066
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter
Conditions
Tamb = 40 C to +85 C
VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V
VIL LOW-level input voltage VCC = 4.5 V to 5.5 V
II
input leakage current
VI = VCC or GND; VCC = 5.5 V
Min Typ[1] Max Unit
2.0 1.6
-V
- 1.2 0.8 V
- - 1.0 A
74HC_HCT4066
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 3 December 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
7 of 24

7페이지


구       성 총 24 페이지수
다운로드[ 74HC4066.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
74HC4060

14-stage binary ripple counter with oscillator

Philips
Philips
74HC4060

14-stage binary ripple counter

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵