IRU1175 Datasheet PDF - International Rectifier
| Part Number | IRU1175 | |
| Description | 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR | |
| Manufacturers | International Rectifier | |
| Logo |  |
|
|
There is a preview and IRU1175 download ( pdf file ) link at the bottom of this page. Total 6 Pages | ||
Preview 1 page No Preview Available !
IRU1175
FEATURES
7.5A ULTRA LOW DROPOUT POSITIVE
ADJUSTABLE REGULATOR
PRELIMINARY DATASHEET
DESCRIPTION
0.5V Dropout at 7.5A (Equivalent of 67mΩ)
Fast Transient Response
1% Voltage Reference Initial Accuracy
Built-in Thermal Shutdown
APPLICATIONS
3.3V to 2.7V Intel I740 chipset
The IRU1175 is a 7.5A regulator with extremely low drop-
out voltage using a proprietary bipolar process that
achieves comparable equivalent on resistance to that of
discrete MOSFETs. This product is specifically designed
to provide well regulated supply for applications requir-
ing very low dropout such as 2.8V from 3.3V ATX power
supplies where the same efficiency as the switcher can
be achieved without the cost and complexity associ-
ated with switching regulators. One such application is
the new graphic chipsets that requires 2.7V supply such
as the Intel I740 chipset.
TYPICAL APPLICATION
3.3V
C1
100uF
Vin 5
IRU1175
Vctrl 4
Vout 3
Adj 2
1175app1-1.0
5V
Vsense 1
C2
10uF
R1
100
1%
R2
124
1%
Typical application of IRU1175
2.7V
C3
100uF
PACKAGE ORDER INFORMATION
Tj (°C)
0 TO 125
5-PIN PLASTIC 5-PIN PLASTIC 8-PIN PLASTIC
TO-263 (M) ULTRA THIN-PAK (P) SOIC (S)
IRU1175CM
IRU1175CP
IRU1175CS
Rev. 1.2
11/29/99
2-79
|
| |
 
IRU1175
The IRU1175 keeps a constant 1.25V between the
Vsense pin and the Vadj pin. By placing a resistor R1
across these two pins and connecting the Vsense and
Vout pin together, a constant current flows through R1,
adding to the Iadj current and into the R2 resistor pro-
ducing a voltage equal to the (1.25/R1)*R2 + Iadj*R2.
This voltage is then added to the 1.25V to set the output
voltage. This is summarized in the above equation. Since
the minimum load current requirement of the IRU1175 is
10mA, R1 is typically selected to be a 121Ω resistor so
that it automatically satisfies this condition. Notice that
since the Iadj is typically in the range of 50µA it only
adds a small error to the output voltage and should be
considered when very precise output voltage setting is
required.
Load Regulation
For most applications a minimum of 100µF aluminum
electrolytic capacitor such as Sanyo, MVGX series,
Panasonic FA series as well as the Nichicon PL series
insures both stability and good transient response.
Thermal Design
The IRU1175 incorporates an internal thermal shutdown
that protects the device when the junction temperature
exceeds the allowable maximum junction temperature.
Although this device can operate with junction tempera-
tures in the range of 150°C, it is recommended that the
selected heat sink be chosen such that during maxi-
mum continuos load operation the junction temperature
is kept below this number. The example below shows
the steps in selecting the proper surface mount pack-
age.
Since the IRU1175 has separate pins for the output (Vout)
and the sense (Vsense), it is ideal for providing true re-
mote sensing of the output voltage at the load. This
means that the voltage drops due to parasitic resistance
such as PCB traces between the regulator and the load
are compensated for using remote sensing. Figure 3
shows a typical application of the IRU1175 with remote
sensing.
Assuming, the following conditions:
Vout=2.7V
Vin=3.3V
Vctrl=5V
Iout=2A DC Avg
Calculate the maximum power dissipation using the fol-
lowing equation:
Vin
Vctrl
Vin Vout
IRU1175
Vctrl
Vsense
Adj
R1
Pd=Iout*(Vin-Vout) + (Iout/60)*(Vctrl - Vout)
Pd=2*(3.3-2.7) + (2/60)*(5-2.7)=1.28 W
RL Using table below select the proper package and the
amount of copper board needed.
R2
1175app3-1.0
Figure 3 - Schematic showing connection for best
load regulation
Stability
The IRU1175 requires the use of an output capacitor as
part of the frequency compensation in order to make the
regulator stable. Typical designs for the microproces-
sor applications use standard electrolytic capacitors with
typical ESR in the range of 50 to 100mΩ and an output
capacitance of 500 to 1000µF. Fortunately as the ca-
pacitance increases, the ESR decreases resulting in a
fixed RC time constant. The IRU1175 takes advantage
of this phenomena in making the overall regulator loop
stable.
Pkg Copper θJA(°C/W)
Area
TO-263 1.4"X1.4" 25
TO-263 1.0"X1.0" 30
TO-263 0.7"X0.7" 35
TO-263 Pad Size 45
SO-8 1.0"X1.0" 55
Max Pd
(Ta=25°C)
4.4W
3.7W
3.1W
2.4W
2.0W
Max Pd
(Ta=45°C)
3.6W
3.0W
2.6W
2.0W
1.63W
Note: Above table is based on the maximum junction
temperature of 135°C.
As shown in the above table, any of the two packages
will do the job. For low cost applications the SO-8 pack-
age is recommended.
Rev. 1.2
11/29/99
2-83
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for IRU1175 electronic component. |
| Information | Total 6 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ IRU1175.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| IRU1175 | The function is 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR. International Rectifier | |
| IRU1176 | The function is 7.5A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR. International Rectifier | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
IRU1
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||