Datasheet.kr   

AOZ1034PI 데이터시트 PDF




Alpha & Omega Semiconductors에서 제조한 전자 부품 AOZ1034PI은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 AOZ1034PI 자료 제공

부품번호 AOZ1034PI 기능
기능 4A Synchronous Buck Regulator
제조업체 Alpha & Omega Semiconductors
로고 Alpha & Omega Semiconductors 로고


AOZ1034PI 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 18 페이지수

미리보기를 사용할 수 없습니다

AOZ1034PI 데이터시트, 핀배열, 회로
AOZ1034
EZBuck™ 4A Synchronous Buck Regulator
General Description
The AOZ1034 is a synchronous high efficiency, simple to
use, 4A buck regulator. The AOZ1034 works from a 4.5V
to 18V input voltage range, and provides up to 4A of
continuous output current with an output voltage
adjustable down to 0.8V.
The AOZ1034 comes in both a 5x4 DFN-8 and an
exposed pad SO-8 package and is rated over a
-40°C to +85°C ambient temperature range.
Features
z 4.5V to 18V operating input voltage range
z Synchronous rectification: 60mΩ internal high-side
switch and 20mΩ Internal low-side switch
z High efficiency: up to 95%
z Internal soft start
z Output voltage adjustable to 0.8V
z 4A continuous output current
z Fixed 500kHz PWM operation
z Cycle-by-cycle current limit
z Pre-bias start-up
z Short-circuit protection
z Thermal shutdown
z Thermally enhanced 5x4 DFN-8 and exposed pad
SO-8 packages
Applications
z Point of load DC/DC conversion
z PCIe graphics cards
z Set top boxes
z DVD drives and HDD
z LCD panels
z Cable modems
z Telecom/Networking/Datacom equipment
Typical Application
VIN
C1
22µF
Ceramic
RC
CC
VIN
EN AOZ1034 LX
COMP
AGND
FB
PGND
L1
4.7µH
VOUT
R1
C2, C3
22µF
Ceramic
R2
Rev. 1.1 September 2010
Figure 1. 3.3V 4A Synchronous Buck Regulator
www.aosmd.com
Page 1 of 18
Free Datasheet http://www.datasheet4u.com/




AOZ1034PI pdf, 반도체, 판매, 대치품
AOZ1034
Electrical Characteristics
TA = 25°C, VIN = VEN = 12V, VOUT = 3.3V unless otherwise specified. Specifications in BOLD indicate a temperature range of
-40°C to +85°C.
Symbol
Parameter
Conditions
Min.
Typ.
Max Units
VIN
VUVLO
IIN
Supply Voltage
Input Under-voltage Lockout
Threshold
Supply Current (Quiescent)
IOFF Shutdown Supply Current
VFB Feedback Voltage
Load Regulation
Line Regulation
IFB Feedback Voltage Input Current
VEN EN input threshold
VHYS
EN Input hysteresis
MODULATOR
fO
DMAX
Ton_min
Frequency
Maximum Duty Cycle
Minimum On Time
Error Amplifier Voltage Gain
Error Amplifier Transconductance
PROTECTION
ILIM Current Limit
Over-temperature Shutdown Limit
tSS Soft Start Interval
OUTPUT STAGE
High-side Switch On-resistance
Low-side Switch On-resistance
VIN rising
VIN falling
IOUT = 0, VFB = 1.2V,
VEN >1.2V
VEN = 0V
TA = 25°C
Off threshold
On threshold
TJ rising
TJ falling
VIN = 12V
VIN = 5V
VIN = 12V
VIN = 5V
4.5 18 V
4.1 V
3.7 V
1.6 2.5 mA
1 10 μA
0.788 0.8 0.812 V
0.5 %
1%
200 nA
0.6 V
2V
100 mV
400 500 600 kHz
100 %
150 ns
500 V / V
200 μA / V
5.0 5.5
150
100
3
A
°C
°C
ms
60 mΩ
75
20 mΩ
30
Rev. 1.1 September 2010
www.aosmd.com
Page 4 of 18
Free Datasheet http://www.datasheet4u.com/

4페이지










AOZ1034PI 전자부품, 판매, 대치품
AOZ1034
Detailed Description
The AOZ1034 is a current-mode step down regulator
with integrated high-side PMOS switch and a low-side
NMOS switch. It operates from a 4.5V to 18V input
voltage range and supplies up to 4A of load current.
Features include enable control, Power-On Reset, input
under voltage lockout, output over voltage protection,
active high power good state, fixed internal soft-start and
thermal shut down.
The AOZ1034 comes in both a 5x4 DFN-8 and an
exposed pad SO-8 package.
Enable and Soft Start
The AOZ1034 has internal soft start feature to limit
in-rush current and ensure the output voltage ramps up
smoothly to regulation voltage. A soft start process
begins when the input voltage rises to 4.1V and voltage
on EN pin is HIGH. In soft start process, the output
voltage is ramped to regulation voltage in typically 3ms.
The 3ms soft start time is set internally.
The EN pin of the AOZ1034 is active high. Connect the
EN pin to VIN if enable function is not used. Pull it to
ground will disable the AOZ1034. Do not leave it open.
The voltage on EN pin must be above 2V to enable the
AOZ1034. When voltage on EN pin falls below 0.6V, the
AOZ1034 is disabled. If an application circuit requires the
AOZ1034 to be disabled, an open drain or open collector
circuit should be used to interface to EN pin.
Steady-State Operation
Under steady-state conditions, the converter operates
in fixed frequency and Continuous-Conduction Mode
(CCM).
The AOZ1034 integrates an internal P-MOSFET as the
high-side switch. Inductor current is sensed by amplifying
the voltage drop across the drain to source of the high
side power MOSFET. Output voltage is divided down by
the external voltage divider at the FB pin. The difference
of the FB pin voltage and reference is amplified by the
internal transconductance error amplifier. The error
voltage, which shows on the COMP pin, is compared
against the current signal, which is sum of inductor
current signal and ramp compensation signal, at PWM
comparator input. If the current signal is less than the
error voltage, the internal high-side switch is on. The
inductor current flows from the input through the inductor
to the output. When the current signal exceeds the error
voltage, the high-side switch is off. The inductor current is
freewheeling through the internal low-side N-MOSFET
switch to output. The internal adaptive FET driver
guarantees no turn on overlap of both high-side and
low-side switch.
Comparing with regulators using freewheeling Schottky
diodes, the AOZ1034 uses freewheeling NMOSFET to
realize synchronous rectification. It greatly improves the
converter efficiency and reduces power loss in the
low-side switch.
The AOZ1034 uses a P-Channel MOSFET as the
high-side switch. It saves the bootstrap capacitor
normally seen in a circuit which is using an NMOS
switch. It allows 100% turn-on of the high-side switch to
achieve linear regulation mode of operation.
Switching Frequency
The AOZ1034 switching frequency is fixed and set by an
internal oscillator. The practical switching frequency
could range from 400kHz to 600kHz due to device
variation.
Light Load Mode
The AOZ1034 includes is a Pulse-Skip architecture for
Light Load operation, enabling increased efficiency
during standby. Under Heavy Loads, the controller
operates in a standard Synchronous Mode using the
high-side PMOS as control FET and low-side NMOS as
synchronous rectifier NMOS. During Light Loads, the
controller automatically switches to a Non-Synchronous
mode using the high-side PMOS as control FET and the
integrated diode as freewheeling rectifier diode.
Output Voltage Programming
Output voltage can be set by feeding back the output to
the FB pin by using a resistor divider network. In the
application circuit shown in Figure 1. The resistor divider
network includes R1 and R2. Usually, a design is started
by picking a fixed R2 value and calculating the required
R1 with equation below.
VO
=
0.8
×
1
+
R-----1-⎟⎞
R2
Some standard value of R1, R2 and most used output
voltage values are listed in Table 1 on the next page.
Rev. 1.1 September 2010
www.aosmd.com
Page 7 of 18
Free Datasheet http://www.datasheet4u.com/

7페이지


구       성 총 18 페이지수
다운로드[ AOZ1034PI.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AOZ1034PI

4A Synchronous Buck Regulator

Alpha & Omega Semiconductors
Alpha & Omega Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵