Datasheet.kr   

EKI06108 데이터시트 PDF




SANKEN에서 제조한 전자 부품 EKI06108은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 EKI06108 자료 제공

부품번호 EKI06108 기능
기능 N Channel Trench Power MOSFET
제조업체 SANKEN
로고 SANKEN 로고


EKI06108 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 9 페이지수

미리보기를 사용할 수 없습니다

EKI06108 데이터시트, 핀배열, 회로
60 V, 57 A, 7.0 mΩ Low RDS(ON)
N ch Trench Power MOSFET
EKI06108
Features
V(BR)DSS --------------------------------- 60 V (ID = 100 µA)
ID ---------------------------------------------------------- 57 A
RDS(ON) ----------9.2 mΩ max. (VGS = 10 V, ID = 28.5 A)
Qg------16.9 nC (VGS = 4.5 V, VDS = 30 V, ID = 28.5 A)
Low Total Gate Charge
High Speed Switching
Low On-Resistance
Capable of 4.5 V Gate Drive
100 % UIL Tested
RoHS Compliant
Package
TO-220
(4)
D
(1) (2) (3)
GDS
Applications
DC-DC converters
Synchronous Rectification
Power Supplies
Equivalent circuit
D(2)(4)
G(1)
S(3)
Not to scale
Absolute Maximum Ratings
Unless otherwise specified, TA = 25 °C
Parameter
Symbol
Drain to Source Voltage
VDS
Gate to Source Voltage
VGS
Continuous Drain Current
ID
Pulsed Drain Current
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
IDM
IS
ISM
Single Pulse Avalanche Energy
EAS
Avalanche Current
Power Dissipation
Operating Junction Temperature
Storage Temperature Range
IAS
PD
TJ
TSTG
Test conditions
TC = 25 °C
PW 100µs
Duty cycle 1 %
PW 100µs
Duty cycle 1 %
VDD = 30 V, L = 1 mH,
IAS = 9.4 A, unclamped,
RG = 4.7 Ω
Refer to Figure 1
TC = 25 °C
Rating
60
± 20
57
114
57
114
89
16.7
90
150
55 to 150
Unit
V
V
A
A
A
A
mJ
A
W
°C
°C
EKI06108-DS Rev.1.3
May. 29, 2014
SANKEN ELECTRIC CO.,LTD.
http://www.sanken-ele.co.jp
1




EKI06108 pdf, 반도체, 판매, 대치품
EKI06108
RDS(ON)-ID characteristics (typical)
VGS=10V
25
20
15 Tc = 125
75
10
25
5
0
0 20 40 60 80 100 120
ID (A)
VDS-VGS characteristics (typical)
Tc=25
0.4
0.3
0.2
0.1
0.0
0
ID=22.8A
ID=18.9A
ID=14.3A
5 10
VGS (V)
15
RDS(ON)-ID characteristics (typical)
VGS=4.5V
30
25
20
Tc = 125
15
75
10 25
5
0
0 20 40 60 80 100 120
ID (A)
IDR-VSD characteristics (typical)
Tc=25
120
100 VGS=10V
80
VGS=4.5V
60
3V
40
0V
20
0
0 0.5 1 1.5
VSD (V)
ID-VGS characteristics (typical)
VDS=5V
120
100
80
60
Tc =125
40
75
20 25
0
0123456
VGS (V)
IDR-VSD characteristics (typical)
VDS=0V
120
100
80
60 Tc =125
40 75
25
20
0
0 0.5 1 1.5
VSD (V)
Capacitance-VDS characteristics (typical)
10000
Ciss
1000
Coss
100
Ta=25
VGS=0V
f =1MHz
10
0 10
Crss
20 30
VDS (V)
40
50
RDS(ON)-Tc characteristics (typical)
20
16
12
8
4 ID=28.5A
VGS=10V
0
25 50 75 100 125 150
Tc ()
VGS - Qg characteristics (typical)
15
10
5
Tc=25
VDS=30V
ID=28.5A
0
0 10 20 30 40
Qg (nC)
RDS(ON)-Tc characteristics (typical)
20
16
12
8
4
ID=14.3A
VGS=4.5V
0
25 50 75 100 125 150
Tc ()
EKI06108-DS Rev.1.3
May. 29, 2014
SANKEN ELECTRIC CO.,LTD.
Vth-Tc characteristics (typical)
3
2
1
ID=650uA
VGS=VDS
0
25 50 75 100 125 150
Tc ()
BVDSS-Tc characteristics (typical)
78
76
74
72
70
68 ID=1mA
VGS=0V
66
64
25 50 75 100 125 150
Tc ()
4

4페이지










EKI06108 전자부품, 판매, 대치품
EKI06108
OPERATING PRECAUTIONS
In the case that you use Sanken products or design your products by using Sanken products, the reliability largely
depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation
range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to
assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric
current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused
due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum
values must be taken into consideration. In addition, it should be noted that since power devices or IC’s including power
devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly.
Because reliability can be affected adversely by improper storage environments and handling methods, please
observe the following cautions.
Cautions for Storage
Ensure that storage conditions comply with the standard temperature (5 to 35°C) and the standard relative humidity
(around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity.
Avoid locations where dust or harmful gases are present and avoid direct sunlight.
Reinspect for rust on leads and solderability of the products that have been stored for a long time.
Cautions for Testing and Handling
When tests are carried out during inspection testing and other standard test periods, protect the products from power
surges from the testing device, shorts between the product pins, and wrong connections. Ensure all test parameters are
within the ratings specified by Sanken for the products.
Remarks About Using Thermal Silicone Grease
When thermal silicone grease is used, it shall be applied evenly and thinly. If more silicone grease than required is
applied, it may produce excess stress.
The thermal silicone grease that has been stored for a long period of time may cause cracks of the greases, and it
cause low radiation performance. In addition, the old grease may cause cracks in the resin mold when screwing the
products to a heatsink.
Fully consider preventing foreign materials from entering into the thermal silicone grease. When foreign material
is immixed, radiation performance may be degraded or an insulation failure may occur due to a damaged insulating
plate.
The thermal silicone greases that are recommended for the resin molded semiconductor should be used.
Our recommended thermal silicone grease is the following, and equivalent of these.
Type
Suppliers
G746 Shin-Etsu Chemical Co., Ltd.
YG6260 Momentive Performance Materials Japan LLC
SC102 Dow Corning Toray Co., Ltd.
Cautions for Mounting to a Heatsink
When the flatness around the screw hole is insufficient, such as when mounting the products to a heatsink that has
an extruded (burred) screw hole, the products can be damaged, even with a lower than recommended screw torque.
For mounting the products, the mounting surface flatness should be 0.05mm or less.
Please select suitable screws for the product shape. Do not use a flat-head machine screw because of the stress to
the products. Self-tapping screws are not recommended. When using self-tapping screws, the screw may enter the
hole diagonally, not vertically, depending on the conditions of hole before threading or the work situation. That
may stress the products and may cause failures.
Recommended screw torque:
Package
Recommended Screw Torque
TO-220, TO-220F
0.490 to 0.686 Nm (5 to 7 kgfcm)
TO-3P, TO-3PF, TO-247 0.686 to 0.882 Nm (7 to 9 kgfcm)
SLA 0.588 to 0.784 Nm (6 to 8 kgfcm)
EKI06108-DS Rev.1.3
May. 29, 2014
SANKEN ELECTRIC CO.,LTD.
7

7페이지


구       성 총 9 페이지수
다운로드[ EKI06108.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
EKI06108

N Channel Trench Power MOSFET

SANKEN
SANKEN

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵