Datasheet.kr   

BD9413F PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 BD9413F
기능 White LED Driver
제조업체 ROHM
로고 ROHM 로고 



전체 30 페이지

		

No Preview Available !

BD9413F 데이터시트, 핀배열, 회로
Datasheet
LED Drivers for LCD Backlights
1ch Boost up type
White LED Driver for large LCD
BD9413F
1.1 General Description
BD9413F is a high efficiency driver for white LEDs and is
designed for large LCDs. BD9413F has a boost DCDC
converter that employs an array of LEDs as the light
source.
BD9413F has some protect functions against fault
conditions, such as over-voltage protection (OVP), over
current limit protection of DCDC (OCP), LED OCP
protection, and Over boost protection (FBMAX).
Therefore it is available for the fail-safe design over a
wide range output voltage.
Key Specifications
Operating power supply voltage range: 9.0V to 35.0V
Oscillator frequency of DCDC: 150kHz (RT=100k)
Operating Current:
3.3 mA(Typ.)
Operating temperature range:
-40°C to +105°C
1.2 Package(s)
SOP18
W(Typ) x D(Typ) x H(Max)
11.20mm x 7.80mm x 2.01mm
Pin pitch 1.27mm
Features
DCDC converter with current mode
LED protection circuit (Over boost protection, LED
OCP protection)
Over-voltage protection (OVP) for the output voltage
Vout
Adjustable soft start
Adjustable oscillation frequency of DCDC
Wide range of analog dimming 0.2V to 3.0V
UVLO detection for the input voltage of the power
stage
LED Dimming PWM Over Duty Protection(ODP)
Applications
TV, Computer Display, LCD Backlighting
Figure 1. SOP18
Typical Application Circuit
VCC VIN
Vout
VCC UVLO OVP
REG90
STB
GATE
RT
SS CS
FAILB
PWM
DIMOUT
ADIM
ISENSE
DUTYP
DUTYON
GND
FB
Rs
Figure 2. Typical Application Circuit
Product structureSilicon monolithic integrated circuit
.www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
This product has not designed protection against radioactive rays
1/33
TSZ02201-0F2F0C100120-1-2
28.Dec.2015 Rev.001




BD9413F pdf, 반도체, 판매, 대치품
BD9413F
1.6 Absolute Maximum Ratings (Ta=25°C)
Parameter
Power Supply Voltage
SS, RT, ISENSE, FB, CS,
DUTYP Pin Voltage
REG90, DIMOUT, GATE
Pin Voltage
OVP, UVLO, PWM, ADIM, STB,
FAILB, DUTYON
Pin Voltage
Power Dissipation
Symbol
VCC
SS, RT, ISENSE, FB, CS,
DUTYP
REG90, DIMOUT, GATE
OVP, UVLO, PWM,
ADIM, STB, FAILB,
DUTYON
Pd
Rating
-0.3 to +36
-0.3 to +7
-0.3 to +13
-0.3 to +20
0.69 (Note 1)
Operating Temperature Range
Topr
-40 to +105
Junction Temperature
Tjmax
150
Storage Temperature Range
Tstg
-55 to +150
(Note 1) In the case of mounting 1 layer glass epoxy base-plate of 70mm×70mm×1.6mm,
derate by 5.5mW/°C when operating above Ta=25°C.
Datasheet
Unit
V
V
V
V
W
°C
°C
°C
1.7 Recommended Operating Ranges
Parameter
Power Supply Voltage
DC/DC Oscillation Frequency
Effective Range of ADIM Signal
PWM Input Frequency
Symbol
VCC
fsw
VADIM
FPWM
Range
9.0 to 35.0
50 to 1000
0.2 to 3.0
90 to 2000
Unit
V
kHz
V
Hz
1.8 Electrical Characteristics 1/2 (Unless otherwise specified VCC=24V Ta=25°C)
Parameter
Symbol
Min Typ Max Unit
Total Current Consumption
Circuit Current
Icc 3.3 6.6 mA
Circuit Current (standby)
IST 40 80 μA
UVLO Block
Operation VoltageVCC
VUVLO_VCC 6.5 7.5 8.5
V
Hysteresis VoltageVCC
VUHYS_VCC 150 300 600 mV
UVLO Release Voltage
VUVLO
2.88 3.00 3.12
V
UVLO Hysteresis Voltage
VUHYS
250 300 350 mV
UVLO Pin Leak Current
UVLO_LK
-2
0
2 μA
DC/DC Block
ISENSE Threshold Voltage 1
VLED1
0.225 0.233 0.242
V
ISENSE Threshold Voltage 2
VLED2
0.656 0.667 0.677
V
ISENSE Threshold Voltage 3
VLED3
0.988 1.000 1.012
V
ISENSE Clamp Voltage
VLED4
0.990 1.015 1.040
V
Oscillation Frequency
RT Short Protection Range
RT Terminal Voltage
GATE Pin MAX DUTY Output
GATE Pin ON Resistance
(as source)
GATE Pin ON Resistance
(as sink)
SS Pin Source Current
SS Pin ON Resistance at OFF
Soft Start Ended Voltage
FCT 142.5 150 157.5
RT_DET
VRT
-0.3
-
VRT
×90%
1.6 2.0 2.4
MAX_DUTY
90
95
99
RONSO
2.5 5.0 10.0
RONSI
ISSSO
RSS_L
VSS_END
2.0 4.0 8.0
-3.75 -3.0 -2.25
- 3.0 5.0
3.52 3.70 3.88
kHz
V
V
%
μA
k
V
Conditions
VSTB=3.0V, PWM=3.0V
VSTB=0V
VCC=SWEEP UP
VCC=SWEEP DOWN
VUVLO=SWEEP UP
VUVLO=SWEEP DOWN
VUVLO=4.0V
VADIM=0.7V
VADIM=2.0V
VADIM=3.0V
VADIM=3.3V
(as masking analog dimming)
RT=100k
RT=SWEEP DOWN
RT=100k
RT=100k
VSS=2.0V
SS=SWEEP UP
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
4/33
TSZ02201-0F2F0C100120-1-2
28.Dec.2015 Rev.001

4페이지










BD9413F 전자부품, 판매, 대치품
BD9413F
Datasheet
2.1 Pin Descriptions
Pin 1: VCC
This is the power supply pin of the IC. Input range is from 9V to 35V.
The operation starts at more than 7.5V(typ.) and shuts down at less than 7.2V(typ.).
Pin 2: STB
This is the ON/OFF setting terminal of the IC. Input reset-signal to this terminal to reset IC from latch-off.
At startup, internal bias starts at high level, and then PWM DCDC boost starts after PWM rise edge inputs.
Note: IC status (IC ON/OFF) transits depending on the voltage inputted to STB terminal. Avoid the use of intermediate
level (from 0.8V to 2.0V).
Pin 3: OVP
The OVP terminal is the input for over-voltage protection. If OVP is more than 3.0V(typ), the over-voltage protection
(OVP) will work. At the moment of these detections, it sets GATE=L, DIMOUT=L and starts to count up the abnormal
interval. If OVP detection continued to count four GATE clocks, IC reaches latch off. (Please refer to “3.5.5 Timing Chart”)
The OVP pin is high impedance, because the internal resistance is not connected to a certain bias.
Even if OVP function is not used, pin bias is still required because the open connection of this pin is not a fixed potential.
The setting example is separately described in the section ”3.2.7 OVP Setting”.
Pin 4: UVLO
Under Voltage Lock Out pin is the input voltage of the power stage. , IC starts the boost operation if UVLO is more than
3.0V(typ) and stops if lower than 2.7V(typ).
The UVLO pin is high impedance, because the internal resistance is not connected to a certain bias.
Even if UVLO function is not used, pin bias is still required because the open connection of this pin is not a fixed
potential.
The setting example is separately described in the section ”3.2.5 UVLO Setting”
Pin 5: SS
This is the pin which sets the soft start interval of DC/DC converter. It performs the constant current charge of 3.0 μA(typ.)
to external capacitance Css. The switching duty of GATE output will be limited during 0V to 3.7V(typ.) of the SS voltage.
So the soft start interval Tss can be expressed as follows
TSS 1.23 106 CSS [sec]   Css: the external capacitance of the SS pin.
The logic of SS pin asserts low is defined as the latch-off state or PWM is not input high level after STB reset release.
When SS capacitance is under 1nF, take note if the in-rush current during startup is too large, or if over boost detection
(FBMAX) mask timing is too short.
Please refer to soft start behavior in the section “3.5.4 Timing Chart ”.
Pin 6: DUTYON
This is the ON/OFF setting terminal of the LED PWM Over Duty Protection (ODP). By adjusting DUTYON input voltage, it
is ON/OFF of the ODP adjusted.
State
ODP=ON
ODP=OFF
DUTYON input voltage
DUTYON=0.3V~0.8V
DUTYON=1.5V~18.0V
Pin 7: PWM
This is the PWM dimming signal input terminal. The high / low level of PWM pins are the following.
State
PWM=H
PWM=L
PWM input voltage
PWM=1.5V to 18.0V
PWM=0.3V to 0.8V
Pin 8: FAILB
This is FAILB signal output (OPEN DRAIN) pin. At normal operation, NMOS will be OPEN state, during abnormality
detection NMOS will be in ON (500 ohm typ.) state.
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
7/33
TSZ02201-0F2F0C100120-1-2
28.Dec.2015 Rev.001

7페이지



구       성총 30 페이지
다운로드[ BD9413F.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
BD9413F

White LED Driver

ROHM
ROHM

DataSheet.kr    |   2019   |  연락처   |  링크모음   |   검색  |   사이트맵