DataSheet39.com

What is 2N7426?

This electronic component, produced by the manufacturer "ETC", performs the same function as "P-Channel Transistor".


2N7426 Datasheet PDF - ETC

Part Number 2N7426
Description P-Channel Transistor
Manufacturers ETC 
Logo ETC Logo 


There is a preview and 2N7426 download ( pdf file ) link at the bottom of this page.





Total 22 Pages



Preview 1 page

No Preview Available ! 2N7426 datasheet, circuit

The documentation and process conversion measures
necessary to comply with this document shall be
completed by 6 February 2014.
INCH-POUND
MIL-PRF-19500/660E
6 December 2013
SUPERSEDING
MIL-PRF-19500/660D
11 February 2013
PERFORMANCE SPECIFICATION SHEET
SEMICONDUCTOR DEVICE, FIELD EFFECT RADIATION HARDENED
TRANSISTOR, P-CHANNEL SILICON, TYPES 2N7424, 2N7425, AND 2N7426,
JANTXVR, JANTXVF, JANSR, AND JANSF
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of
this specification sheet and MIL-PRF-19500.
1. SCOPE
1.1 Scope. This specification covers the performance requirements for a P-channel, enhancement-mode,
MOSFET, radiation hardened, power transistor. Two levels of product assurance are provided for each device type
as specified in MIL-PRF-19500, with avalanche energy maximum rating (EAS) and maximum avalanche current (IAS).
See 6.5 for JANHC and JANKC die versions.
1.2 Physical dimensions. See figure 1, TO-254AA.
1.3 Maximum ratings. Unless otherwise specified, TA = +25oC.
Type
PT (1) PT R θJC VDS VDG VGS ID1 (3) (4) ID2 (3)(4) IS
TC =
TA =
(2)
TC =+25°C TC =
+25°C +25°C
+100°C
IDM TJ
(5) and
TSTG
2N7424
2N7425
2N7426
W
W °C/W V dc V dc V dc
A dc
250
3.0 0.50 -60 -60
±20
-35
250 3.0 0.50 -100 -100 ±20 -35
250 3.0 0.50 -200 -200 ±20 -27
A dc
-30
-24
-17
A dc
-35
-35
-27
A (pk)
-140
-140
-108
°C
-55
to
+150
(1) Derate linearly 2.0 W/°C for TC > +25°C.
(2) See figure 2, thermal impedance curves.
(3) The following formula derives the maximum theoretical ID limit. ID is limited by package and internal
construction.
ID =
TJM - TC
( RθJC ) x ( RDS ( on ) at TJM )
(4) See figure 3, maximum drain current graphs.
(5) IDM = 4 x ID1 as calculated in note 3.
Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime,
ATTN: VAC, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to [email protected]. Since contact
information can change, you may want to verify the currency of this address information using the ASSIST
Online database at https://assist.dla.mil.
AMSC N/A
FSC 5961

line_dark_gray
2N7426 equivalent
MIL-PRF-19500/660E
4. VERIFICATION
4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:
a. Qualification inspection (see 4.2).
b. Screening (see 4.3).
c. Conformance inspection (see 4.4 and tables I and II).
4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-19500.
4.2.1 Group E qualification. Group E inspection shall be performed for qualification or re-qualification only. In
case qualification was awarded to a prior revision of the specification sheet that did not request the performance of
table III tests, the tests specified in table III herein that were not performed in the prior revision shall be performed on
the first inspection lot of this revision to maintain qualification.
4.2.1.1 Single event effects (SEE). SEE shall be performed at initial qualification and after process or design
changes which may affect radiation hardness (see table III and table IV). Upon qualification, manufacturers shall
provide the verification test conditions from section 5 of method 1080 of MIL-STD-750 that were used to qualify the
device for inclusion into section 6 of the slash sheet. End-point measurements shall be in accordance with table II.
SEE characterization data shall be made available upon request of the qualifying or acquiring activity.
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 2N7426 electronic component.


Information Total 22 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 2N7426.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
2N7424The function is P-Channel Transistor. ETCETC
2N7425The function is P-Channel Transistor. ETCETC
2N7426The function is P-Channel Transistor. ETCETC

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

2N74     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search