|
|
|
부품번호 | MC34C86 기능 |
|
|
기능 | Quad EIA-422-A Line Receiver | ||
제조업체 | Motorola Semiconductors | ||
로고 | |||
전체 4 페이지수
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document
by MC34C86/D
Product Preview
Quad EIA-422-A Line Receiver
CMOS
The MC34C86 is a quad differential line receiver designed for digital data
transmission over balanced lines. The MC34C86 meets all the requirements of
standard EIA–422–A while retaining the low–power characteristics of CMOS.
The MC34C86 has an input sensitivity of 200 mV over the common mode
input voltage range of ± 7 V. In addition, each receiver chain has internal
hysteresis circuitry to improve noise margin and discourage output instability for
slowly changing input waveforms.
The MC34C86 is pin compatible with the MC3486.
All pins are protected against damage due to electrostatic discharges.
• Typical Power Supply Current: 6 mA
• 2000 V ESD Protection on the Inputs and Outputs
• Typical Propagation Delay: 18 ns
• Typical Input Hysteresis: 75 mV
• Meets the Requirements of Standard EIA–422–A
• Operation from Single 5 V Supply
• High Impedance Mode for Outputs Connected to System Buses
• TTL/CMOS Compatible Outputs
MC34C86
16
1
P SUFFIX
PLASTIC DIP
CASE 648
16
1
D SUFFIX
SOG PACKAGE
CASE 751B
ORDERING INFORMATION
MC34C86P
MC34C86D
Plastic DIP
SOG Package
B/D
CONTROL
12
BLOCK DIAGRAM
INPUT INPUT
D2 D1
10 9
+–
INPUT INPUT
B2 B1
14 15
+–
INPUT INPUT
C2 C1
67
+–
INPUT INPUT A/C
A2 A1 CONTROL
21
4
+–
8 16
GND VCC
11
OUTPUT
D
13
OUTPUT
B
5
OUTPUT
C
3
OUTPUT
A
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.
REV 4
10/95
©MOMoTtoOroRla,OInLc.A1995
MC34C86
1
–A–
16
1
H
G
PACKAGE DIMENSIONS
P SUFFIX
PLASTIC DIP
CASE 648–08
9
B
8
FC
S
L
–T–
SEATING
PLANE
KJ
D 16 PL
0.25 (0.010) M T A M
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC
2.54 BSC
H 0.050 BSC
1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0_ 10_ 0_ 10 _
S 0.020 0.040 0.51 1.01
–A–
16
1
D SUFFIX
SOG PACKAGE
CASE 751B–05
9
–B– P 8 PL
8 0.25 (0.010) M B S
G
–T– SEATING
PLANE
K
C
D 16 PL
0.25 (0.010) M T B S A S
R X 45_
F
MJ
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0_ 7_ 0_ 7_
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] – TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC34C86
4
◊
*MC34C86/D*MOMTCO3R4CO8L6A/D
4페이지 | |||
구 성 | 총 4 페이지수 | ||
다운로드 | [ MC34C86.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
MC34C86 | Quad EIA-422-A Line Receiver | Motorola Semiconductors |
MC34C87 | Quad EIA-422-A Line Driver | Motorola Semiconductors |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |