|
|
PDF AT080TN42-V1 Data sheet ( Hoja de datos )
| Número de pieza | AT080TN42-V1 | |
| Descripción | LCD MODULE | |
| Fabricantes | INNOLUX | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AT080TN42-V1 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
|
No Preview Available !
INNOLUX DISPLAY CORPORATION
LCD MODULE
S P E C I F I C AT I O N
Customer:
Model Name:
SPEC NO.:
Date:
Version:
AT080TN42 V.1
A080-42-TT-13
2008/05/12
03
□Preliminary Specification
■Final Specification
For Customer’s Acceptance
Approved by
Comment
Approved by
Reviewed by
Prepared by
Joe Lin
2008/06/03
Jack Huang
2008/06/03
Kevin Chen
2008/06/02
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
1 page  
INNOLUX
2. Pin Assignment
SPEC NO.: A080-42-TT-13 Date :2008/05/12
Page:2/23
2.1. TFT LCD Panel Driving Section
1. FPC Connector is used for the module electronics interface. The recommended
model is AF 730L-A2G1T manufactured by P-TWO.
2. LED Light Bar Connector is used for the integral backlight system. The
recommended model is BHSR-02VS-1 manufactured by JST.
Pin No. Symbol I/O
Function
Remark
1
POL
I Polarity selection
2 STVD I/O Vertical start pulse input when U/D= H Note 1
3
OEV
I Output enable
4
CKV
I Vertical clock
5
STVU I/O Vertical start pulse input when U/D= L
Note 1
6
GND
P Power ground
7
EDGSL
I Select rising edge or falling edge
8 VCC P Power supply for digital circuit
9 V9 I Gamma voltage level 9
10 VGL P Gate OFF voltage
11 V2 I Gamma voltage level 2
12 VGH P Gate ON voltage
13 V6 I Gamma voltage level 6
14 U/D I Up/down selection
Note 1, 2
15
VCOM
I Common voltage
16
GND
P Power ground
17
AVDD
P Power supply for analog circuit
18 V14 I Gamma voltage level 14
19 V11 I Gamma voltage level 11
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
5 Page 
INNOLUX
SPEC NO.: A080-42-TT-13 Date :2008/05/12
Page:8/23
3.1.1. Typical Operation Conditions
Item
Symbol
(GND=AVSS=0V, Note 1)
Values
Min.
Typ.
Max.
Unit
Remark
VCC 3.0 3.3 3.6 V Note 2
Power voltage
AVDD
VGH
10.2
15.3
10.4
16.0
10.6
16.7
V
V
VGL -7.7 -7.0 -6.3 V
VCOM
4.10
4.15
4.20
V
Input signal voltage
V1~V7 0.4 AVDD
- AVDD -0.1 V
V8~V14
0.1
- 0.6 AVDD V
Input logic high voltage
VIH
0.7VCC
-
VCC
V
Note 3
Input logic low voltage
VIL
0
-
0.3VCC
V
Note : Be sure to apply VCC and VGL to the LCD first, and then apply VGH.
Note 2: VCC setting should match the signals output voltage (refer to Note 3) of customer’s
system board .
Note 3: STHL, STHR, OEH, L/R, CPH1~CPH3, STVD, STVU, OEV, CKV, U/D.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
11 Page | ||
| Páginas | Total 26 Páginas | |
| PDF Descargar | [ Datasheet AT080TN42-V1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AT080TN42-V1 | LCD MODULE | INNOLUX |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |