|
|
PDF MK3018GAS Data sheet ( Hoja de datos )
| Número de pieza | MK3018GAS | |
| Descripción | 2.5-INCH HARD DISK DRIVE USER MANUAL | |
| Fabricantes | Toshiba | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MK3018GAS (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
MK3018GAS (HDD2169)
2.5-INCH HARD DISK DRIVE
USER MANUAL
Rev 02
11/2006
1 page  
Installation Notes
The drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid
excessive distortion.
In order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be
kept under the PCB.
Space should be kept around the drive to avoid any contact with other parts, which may occur
due to shock or vibration.
The temperature of the top cover and the base must always be kept under 60C to maintain the
required reliability.
Be sure not to cover the breathing hole to keep the pressure inside the drive at a certain level
Do not apply any force to the top cover, except the screw areas on top cover. Maximum force to
the specified area is 2N.
The drive contains several parts which may be easily damaged by ESD (Electric Static
Discharge). Avoid touching the interface connector pins and the surface of PCB. Be sure to use
ESD proof wrist strap when handling drive.
The four mounting screws should be tightened equally with 0.3N-m (3kgf-cm) torque. The depth
should be 3.0mm minimum and 3.5mm maximum.
Placing Hard Drive inside your Computer
• Determine mounting configuration (the drive can be mounted in either a horizontal or vertical
orientation)
• Configure drive for system application.
• Configure the adapter board for the specific system application (if required).
• Install adapter board into an unused PC/AT 16 bit slot (if required).
• Install the I/F cable to the system's 44 pin connector port or adapter board. Ensure pin 1 is
oriented correctly, (pin 1 on the cable is usually identified by a red or blue strip.)
• Set correct drive type in system CMOS
• Refer to applicable manuals for software installation instructions.
Important Note: Disconnect power from your computer system before beginning installation.
Figure 2.HDD Mounting Holes
3
5 Page 
Interface Pin Assignment
DRIVE INTERFACE SIGNALS
PIN SIGNAL PIN SIGNAL
1
RESET
2 GROUND
3 DD 7 4 DD 8
5 DD 6 6 DD 9
7 DD 5 8 DD 10
9
DD 4
10 DD 11
11 DD 3 12 DD 12
13 DD 2 14 DD 13
15 DD 1 16 DD 14
17 DD 0 18 DD 15
19 GROUND 20
KEY
21 DMARQ 22 GROUND
23 DIOW/STOP 24 GROUND
25 DIOR/ 26 GROUND
-DMARDY
HSTROBE
27 IORDY/ 28
-DMARDY/-
DSTROBE
CSEL
29 DMACK 30 GROUND
31 INTRQ 32 IOCS16
33 DA1 34 PDIAG
35 DA0 36 DA 2
37 CS0 38 CS1
39 DASP 40 GROUND
41 +5V (LOGIC) 42 +5V (MOTOR)
43 GROUND 44 RESERVED
Note: Symbol () in front of signal indicates negative logic.
9
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet MK3018GAS.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MK3018GAS | 2.5-INCH HARD DISK DRIVE USER MANUAL | Toshiba |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |