TSOP33330 Datasheet PDF - Vishay
| Part Number | TSOP33330 | |
| Description | IR Receiver Modules | |
| Manufacturers | Vishay | |
| Logo |  |
|
|
There is a preview and TSOP33330 download ( pdf file ) link at the bottom of this page. Total 22 Pages | ||
Preview 1 page No Preview Available !
www.vishay.com
TSOP331.., TSOP333.., TSOP335..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
MECHNICAL DATA
Pinning for TSOP33...:
1 = OUT, 2 = GND, 3 = VS
FEATURES
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Compatible with wave or reflow soldering
(see “P” version of Minimold option datasheets)
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
DESCRIPTION
The TSOP33... series are miniaturized IR receiver modules
for infrared remote control systems. A PIN diode and a
preamplifier are assembled on lead frame, the epoxy
package contains an IR filter.
The demodulated output signal can be directly connected to
a microprocessor for decoding.
The TSOP333.. series devices are optimized to suppress
almost all spurious pulses from energy saving lamps like
CFLs. AGC3 may also suppress some data signals if
continuously transmitted.
The TSOP331.. series are provided primarily for
compatibility with old AGC1 designs. New designs should
prefer the TSOP333.. series containing the newer AGC3.
The TSOP335.. series contain a very robust AGC5. This
series should only be used for critically noisy environments.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
AGC
30 kHz
33 kHz
Carrier
frequency
36 kHz
38 kHz
40 kHz
56 kHz
Package
Pinning
Dimensions (mm)
Mounting
Application
Best remote control code
LEGACY, FOR SHORT BURSTS FOR SHORT BURSTS, NOISY
FOR SHORT BURSTS, VERY
(AGC1)
ENVIRONMENTS (AGC3)
NOISY ENVIRONMENTS (AGC5)
TSOP33130
TSOP33330
TSOP33530
TSOP33133
TSOP33333
TSOP33533
TSOP33136
TSOP33336 (1)(2)(7)
TSOP33536
TSOP33138
TSOP33338 (3)(4)(5)(6)
TSOP33538
TSOP33140
TSOP33340
TSOP33540
TSOP33156
TSOP33356
TSOP33556
Minimold
1 = OUT, 2 = GND, 3 = VS
5.4 W x 6.35 H x 4.9 D
Leaded
Remote control
(1) MCIR (2) RCMM (3) Mitsubishi (4) RECS-80 Code (5) r-map (6) XMP-1, XMP-2 (7) RCMM
Rev. 1.1, 22-Jul-16
1 Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
|
| |
 
www.vishay.com
TSOP331.., TSOP333.., TSOP335..
Vishay Semiconductors
SUITABLE DATA FORMAT
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
When a data signal presented to the device in the
presence of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
• DC light (e.g. from tungsten bulbs sunlight)
• Continuous signals at any frequency
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14).
0
16920
5 10 15
Time (ms)
20
Fig. 13 - IR Disturbance from Fluorescent Lamp
with Low Modulation
0
16921
5 10 15
Time (ms)
20
Fig. 14 - IR Disturbance from Fluorescent Lamp
with High Modulation
Minimum burst length
After each burst of length
A gap time is required of
For bursts greater than
a minimum gap time in the data
stream is needed of
Maximum number of continuous
short bursts/second
MCIR code
RCMM code
XMP-1, XMP-2 code
Suppression of interference from
fluorescent lamps
TSOP331..
6 cycles/burst
6 to 70 cycles
≥ 10 cycles
70 cycles
> 1.2 x burst length
2000
Yes
Yes
Yes
Mild disturbance patterns
are suppressed (example:
signal pattern of Fig. 13)
TSOP333..
6 cycles/burst
6 to 35 cycles
≥ 10 cycles
35 cycles
> 6 x burst length
2000
Preferred
Preferred
Preferred
Complex disturbance patterns
are suppressed (example: signal
pattern of Fig. 14)
TSOP335..
6 cycles/burst
6 to 24 cycles
≥ 10 cycles
24 cycles
> 25 ms
2000
Yes
Yes
Yes
Critical disturbance patterns
are suppressed,
e.g. highly dimmed LCDs
Note
• For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP332.., TSOP334..
Rev. 1.1, 22-Jul-16
5 Document Number: 82742
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for TSOP33330 electronic component. |
| Information | Total 22 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ TSOP33330.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| TSOP33330 | The function is IR Receiver Modules. Vishay | |
| TSOP33333 | The function is IR Receiver Modules. Vishay | |
| TSOP33336 | The function is IR Receiver Modules. Vishay | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
TSOP
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||