Datasheet.kr   

LS027B7DH01 데이터시트 PDF




Sharp에서 제조한 전자 부품 LS027B7DH01은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 LS027B7DH01 자료 제공

부품번호 LS027B7DH01 기능
기능 LCD Module
제조업체 Sharp
로고 Sharp 로고


LS027B7DH01 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 30 페이지수

미리보기를 사용할 수 없습니다

LS027B7DH01 데이터시트, 핀배열, 회로




LS027B7DH01 pdf, 반도체, 판매, 대치품
SPEC No.
MODEL No.
LCP-2110015A
LS027B7DH01
PAGE
2
[For handling and system design]
(1) Handle with care as glass is used in this LCD panel. Dropping or contact against hard object may cause cracks or
chips.
(2) Be careful to handle this LCD panel in order to avoid injury yourself by panel`s edge as this panel is made of glass
and might be a sharp edge.
(3) Do not scratch the surface of the polarizer film as it is easily damaged.
(4) Water droplets on the polarizer film must be wiped off immediately as they may cause color changes, or other
defects if remained for a long time.
(5)Do not leave the LCD panel in direct sun or under ultraviolet ray.
(6) To clean LCD panel surface, wipe clean with absorbent cotton or soft cloth. If further cleaning is needed, use IPA
(isopropyl alcohol) and wipe clean lightly on surface only. Do not use organic solvents as it may damage the LCD
panel terminal area which uses organic material. Also, do not directly touch with finger. When the terminals cleaning
are needed, those should be wiped by a soft cloth or a cotton swab without directly touching by hand.
(7) Do not expose gate driver, etc. on the panel (circuit area outside panel display area) to light as it may not operate
properly. Design that shields gate driver, etc. from light is required when mounting the LCD module.
(8) To avoid circuit failure, do not touch panel terminal area.
(9) Support for the LCD panel should be carefully designed to avoid stress that exceeds specification on glass surface.
(10) When handling LCD module and assembling them into cabinets, be noted that storage in the environment of
oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, and etc. which
generate these gasses, may cause corrosion and discoloration of LCD modules.
(11)To avoid picture uniformity failure, do not put a seal or an adhesive material on the panel surface.
(12) Do not use chloroprene rubber as it generates chlorine gas and affects reliability in LCD panel connective area.
(13) Protective film is attached to both of surface polarizer films (front polarizer and rear polarizer) on LCD panel to
prevent scratches or other damages. Remove these protective films before use. In addition, do not attach the
protective films which are removed from LCD module again. When the LCD panel which has the reattached
protective film is needed to storage for a long time, the polarizer film might have a damage with picture quality failure.
(14) Panel is susceptible to mechanical stress and such stress may affect the display. Place the panel on flat surface
to avoid stress caused by twist, bend, etc.
(15) When transporting LCD panels, secure them in LCD panel tray to avoid mechanical stress. The tray should be
conductive to protect LCD panels from static charge.
Material used in set or epoxy resin (amine type hardening agent) from packaging, and silicon adhesive
(dealcoholized or oxime) all release gas which may affect quality of polarizer film. Do confirm compatibility with user
materials.
(16) As this LCD module is composed electronic circuits, it is sensitive to electrostatic discharge of 200V or more.
Handle with care using cautions for the followings:
z Operators
Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human
body.

4페이지










LS027B7DH01 전자부품, 판매, 대치품
SPEC No.
MODEL No.
LCP-2110015A
LS027B7DH01
PAGE
5
[Other Notice]
(1) Operation outside specified environmental conditions cannot be guaranteed.
(2) As power supply (VDD-GNDVDDA-GND) impedance is lowered during use, bus controller should be inserted
near LCD module as much as possible.
(3) Polarizer film is applied over LCD panel surface. Liquid crystal inside LCD panel deteriorates with ultraviolet ray.
The panel should not be left in direct sun or under strong ultraviolet ray for prolonged period of time even with the
polarizer film.
(4) Disassembling the LCD module will cause permanent damage to the module. Do not disassemble the module.
(5) If LCD panel is broken, do not ingest the liquid crystal from the broken panel. If hand, leg, or clothes come in
contact with liquid crystal, wash off immediately with soap.
(6) ODS (specific chlorofuorocarbon, specific halon, 1-1-1 trichloroethane, carbon tetrachloride) are not used or
contained in material or all production processes of this product.
(7) Observe all other precautionary requirements in handling general electronic components.
Discarding liquid crystal modules
LCD Panel
: Dispose of as glass waste. This LCD module contains no harmful substances.
The liquid crystal panel contains no dangerous or harmful substances.
This liquid crystal panel contains only an extremely small amount of liquid crystal
(approximately 100mg) and therefore it will not leak even if the panel should break.
Its median lethal dose (LD50) is greater than 2,000 mg/kg and a mutagenetic
(Aims test: negative) material is used.
㩷㩷㩷㩷
㩷 㩷 㩷 FPC
:
㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷
(1) FPC bend R should be 0.45mm or greater and R should be even.
In LCD panel an connective area, do not bend FPC into polarizer film side.
(2) Do not hang LCD module by FPC or apply force to FPC.

7페이지


구       성 총 30 페이지수
다운로드[ LS027B7DH01.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LS027B7DH01

LCD Module

Sharp
Sharp

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵