Datasheet.kr   

DLW5ATH151MQ2L 데이터시트 PDF




Murata에서 제조한 전자 부품 DLW5ATH151MQ2L은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 DLW5ATH151MQ2L 자료 제공

부품번호 DLW5ATH151MQ2L 기능
기능 Wire Wound Chip Common Mode Choke Coil
제조업체 Murata
로고 Murata 로고


DLW5ATH151MQ2L 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 11 페이지수

미리보기를 사용할 수 없습니다

DLW5ATH151MQ2L 데이터시트, 핀배열, 회로
Reference Only
Spec. No. JEFL243C-9122-01
P 1/11
Wire Wound Chip Common Mode Choke Coil
DLW5ATH□□□MQ2Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW5ATH_MQ Series for
Automotive Electronics based on AEC-Q200.
2. Part Numbering
(ex.) DL W 5A T H 111 M Q 2 L
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (L×W)
(4) Type
(5) Category
3.Rating
(6) Impedance (Typ. at 100MHz)
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code L : Taping (φ180mm/reel)
K : Taping (φ330mm/reel)
B : Bulk
Customer
Part Number
MURATA
Part Number
DLW5ATH500MQ2L
Impedance
at 10MHz,
Under Standard
Testing Conditions
()
Impedance
at 100MHz,
Under Standard
Testing Conditions
(Typ.)
Rated
Voltage
V(DC)
Withstanding
Voltage
V(DC)
Rated
Current(*)(A)
at
105
at
125
DLW5ATH500MQ2K
4.6min
50
4.0 2.5
DLW5ATH500MQ2B
DLW5ATH151MQ2L
DLW5ATH151MQ2K
11min
150
3.0 2.0
DLW5ATH151MQ2B
DLW5ATH331MQ2L
DLW5ATH331MQ2K
20min
330 50 125 2.5 1.5
DLW5ATH331MQ2B
DLW5ATH501MQ2L
DLW5ATH501MQ2K
35min
500
2.0 1.2
DLW5ATZ501MQ2B
DLW5ATH112MQ2L
DLW5ATH112MQ2K
50min
1100
1.5 1.0
DLW5ATH112MQ2B
DC
Resistance
(Rdc)
(max.)
0.013
0.020
0.027
0.034
0.056
Insulation
Resistance
(Mmin.)
10
ESD
Rank
2.2kV
2
(*)As for DLW5ATH_MQ type Rated Current is derated as following figure depending on the operating temperature.
Rated Current
at 105
Rated Current
at 125
Operating Temperature
(Ambient temperature)[]
105
125
· Operating Temperature : - 40 °C to + 125 °C
· Storage Temperature : - 40 °C to + 125 °C
MURATA MFG CO., LTD.




DLW5ATH151MQ2L pdf, 반도체, 판매, 대치품
Reference Only
Spec. No. JEFL243C-9122-01
No. Stress
20 Flammability
21 Board Flex
22 Terminal Strength
30 Electrical
Transient
Conduction
AEC-Q200
Test Method
Per UL-94
Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60 sec minimum holding time
Per AEC-Q200-006
A force of 17.7N
for 60sec
Per ISO-7637-2
P 4/11
Murata Specification / Deviation
Not Applicable
Meet Table A after testing.
30 sec minimum holding time
No defects
Not Applicable
9. Terminal to be Tested When measuring and suppling the voltage, the following terminal is applied.
No. Item
9.1 Impedance (|Z|)
(Measurement Terminal)
9.2 DC Resistance (Rdc)
(Measurement Terminal)
9.3 Insulation Resistance (I.R.)
(Measurement Terminal)
9.4 Withstanding Voltage
(Measurement Terminal)
9.5 Biased Humidity (Supply Terminal)
Terminal to be Tested
Terminal
Terminal
Terminal
Terminal
9.6 Operational Life (Supply Terminal)
10. Impedance Frequency Characteristics (Typical)
10000
DLW5ATH_MQ series
1000
100
Common mode
DLW5ATH112MQ2
DLW5ATH501MQ2
DLW5ATH331MQ2
DLW5ATH151MQ2
DLW5ATH500MQ2
10
1
1
DLW5ATH331MQ2
DLW5ATH151MQ2
DLW5ATH500MQ2
DLW5ATH112MQ2
DLW5ATH501MQ2
Differential
10 100
Frequency(MHz)
1000
11. P.C.B., Flux, Solder and Soldering condition
Test shall be done using P.C.B., Flux, Solder and Soldering condition which are
specified in item 14 except the case of being specified special condition.
MURATA MFG CO., LTD.

4페이지










DLW5ATH151MQ2L 전자부품, 판매, 대치품
Reference Only
Spec. No. JEFL243C-9122-01
14. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
P 7/11
14.1 Flux and Solder
Flux
Solder
Use rosin-based flux,(with converting chlorine content 0.06 to 0.1(wt)%. ),
but not highly acidic flux
(with Halogen content exceeding 0.2(wt)% conversion to chlorine).
Do not use water-soluble flux.
Use Sn-3.0Ag-0.5Cu solder
14.2 Assembling
Products can be applied to reflow and flow soldering.
< Thermal Shock >
Pre-heating should be in such a way that the temperature difference between solder and
ceramic surface is limited to 100°C max. Also cooling into solvent after soldering
should be in such a way that the temperature difference is limited to 100°C max.
Not enough preheating may cause deterioration in insulation resistance and / or crank or ceramic body.
14.3 Cleaning Conditions
Products shall be cleaned on the following conditions.
(1) Cleaning temperature shall be limited to 60°C max. (40°C max. for IPA.)
(2) Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon
at the mounted products and P.C.B.
Power:20W/ I max. Frequency:28kHz to 40kHz Time:5 min max.
(3) Cleaner
1. Cleaner
·Isopropyl alcohol (IPA)
2.Aqueous agent
·PINE ALPHA ST-100S
(4) There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water
in order to remove the cleaner.
(5) Other cleaning
Please contact us.
14.4 Resin coating
The impedance value may change due to high cure-stress of resin to be used for coating/molding products. An
open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating
condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under
some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful
attention when you select resin in case of coating/molding the products with the resin. Prior to use the coating resin,
please make sure no reliability issue is observed by evaluating products mounted on your board.
14.5 Attention regarding P.C.B. bending
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board.
Products direction
Poor example
a
b
Good example
Products shall be location the sideways
direction (Length:a<b) to the mechanical
stress.
MURATA MFG CO., LTD.

7페이지


구       성 총 11 페이지수
다운로드[ DLW5ATH151MQ2L.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
DLW5ATH151MQ2B

Wire Wound Chip Common Mode Choke Coil

Murata
Murata
DLW5ATH151MQ2K

Wire Wound Chip Common Mode Choke Coil

Murata
Murata

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵