AT80F51-20AI Datasheet PDF - ATMEL Corporation
| Part Number | AT80F51-20AI | |
| Description | 8-Bit Microcontroller with 4K Bytes QuickFlash Memory | |
| Manufacturers | ATMEL Corporation | |
| Logo |  |
|
|
There is a preview and AT80F51-20AI download ( pdf file ) link at the bottom of this page. Total 12 Pages | ||
Preview 1 page No Preview Available !
Features
• Compatible with MCS-51™ Products
• 4K Bytes of Factory Programmable QuickFlash™ Memory
• Fully Static Operation: 0 Hz to 20 MHz
• Three-Level Program Memory Lock
• 128 x 8-Bit Internal RAM
• 32 Programmable I/O Lines
• Two 16-Bit Timer/Counters
• Six Interrupt Sources
• Programmable Serial Channel
• Low Power Idle and Power Down Modes
Description
The AT80F51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K
bytes of QuickFlash Memory. The device is manufactured using Atmel’s high density
nonvolatile memory technology and is compatible with the industry standard MCS-
51™ instruction set and pinout. The on-chip QuickFlash allows custom codes to be
quickly programmed in the factory. By combining a versatile 8-bit CPU with Quick-
Flash on a monolithic chip, the Atmel AT80F51 is a powerful microcomputer which
provides a highly flexible and cost effective solution to many embedded control appli-
cations.
(continued)
Pin Configurations
TQFP
INDEX
CORNER
P1.5
P1.6
P1.7
RST
(RXD) P3.0
NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
4
44
34
24
14
03
93
83
73
6
3
3
5
4
1 33
2 32
3 31
4 30
5 29
6 28
7 27
8 26
9 25
10 24
11 23
1
21
31
41
51
61
71
1
8
9
2
02
12
2
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA
NC
ALE
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
PDIP
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RST
(RXD) P3.0
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
(WR) P3.6
(RD) P3.7
X TA L 2
X TA L 1
GND
1 40
2 39
3 38
4 37
5 36
6 35
7 34
8 33
9 32
10 31
11 30
12 29
13 28
14 27
15 26
16 25
17 24
18 23
19 22
20 21
PLCC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA
ALE
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
INDEX
CORNER
(RXD)
(TXD)
(INT0)
(INT1)
(T0)
(T1)
P1.5
P1.6
P1.7
RST
P3.0
NC
P3.1
P3.2
P3.3
P3.4
P3.5
6 4 2 44 42 40
7 5 3 1 43 4139
8 38
9 37
10 36
11 35
12 34
13 33
14 32
15 31
16 30
11781 92 02 12 22 32 42 52 62 72289
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA
NC
ALE
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
8-Bit
Microcontroller
with 4K Bytes
QuickFlash™
Memory
AT80F51
0979A-A–12/97
3-3
|
| |
 
AT80F51
nated. The only exit from power down is a hardware reset.
Reset redefines the SFRs but does not change the on-chip
RAM. The reset should not be activated before VCC is
restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and sta-
bilize.
Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the addi-
tional features listed in the table below:
Lock Bit Protection Modes
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until reset is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Program Lock Bits
LB1 LB2 LB3
1 UUU
2 PUU
3 PPU
4PPP
Protection Type
No program lock features.
MOVC instructions executed from external program memory are disabled from fetching code
bytes from internal memory, EA is sampled and latched on reset, and further programming of the
QuickFlash is disabled.
Same as mode 2, also verify is disabled.
Same as mode 3, also external execution is disabled.
Programming/Verifying the QuickFlash
The AT80F51 can only be programmed by Atmel. Cus-
tomer codes should be submitted in duplicate on a floppy
disk or uploaded to Atmel’s bulletin board or Web site. The
code should be in the Intel Hex format. The desired states
of the Lock Bits should be specified. Once programmed,
the code memory and Lock Bits cannot be erased or repro-
grammed.
Please consult the factory or Atmel’s representatives for
details on submitting custom codes.
Program Verify: If lock bits LB1 and LB2 have not been
programmed, the programmed code data can be read back
via the address and data lines for verification. The lock bits
QuickFlash Verification Modes
cannot be verified directly. Verification of the lock bits is
achieved by observing that their features are enabled.
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 030H, 031H, and 032H, except that P3.6 and
P3.7 must be pulled to a logic low. The values returned are
as follows.
(030H) = 1EH indicates manufactured by Atmel
(031H) = 80H indicates QuickFlash
(032H) = 01H indicates AT80F51
Mode
Read Code Data
Read Signature Byte
RST
H
H
PSEN
L
L
ALE
H
H
EA P2.6 P2.7 P3.6 P3.7
H L LHH
H LLLL
3-7
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AT80F51-20AI electronic component. |
| Information | Total 12 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ AT80F51-20AI.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| AT80F51-20AC | The function is 8-Bit Microcontroller with 4K Bytes QuickFlash Memory. ATMEL Corporation | |
| AT80F51-20AI | The function is 8-Bit Microcontroller with 4K Bytes QuickFlash Memory. ATMEL Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AT80
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||