AT45D021-RI Datasheet PDF - ATMEL Corporation
| Part Number | AT45D021-RI | |
| Description | 2-Megabit 5-volt Only Serial DataFlash | |
| Manufacturers | ATMEL Corporation | |
| Logo |  |
|
|
There is a preview and AT45D021-RI download ( pdf file ) link at the bottom of this page. Total 18 Pages | ||
Preview 1 page No Preview Available !
Features
• Single 4.5V - 5.5V Supply
• Serial Interface Architecture
• Page Program Operation
– Single Cycle Reprogram (Erase and Program)
– 1024 Pages (264 Bytes/Page) Main Memory
• Two 264-Byte SRAM Data Buffers – Allows Receiving of Data
while Reprogramming of Nonvolatile Memory
• Internal Program and Control Timer
• Fast Page Program Time – 7 ms Typical
• 80 µs Typical Page to Buffer Transfer Time
• Low Power Dissipation
– 15 mA Active Read Current Typical
– 15 µA CMOS Standby Current Typical
• 10 MHz Max Clock Frequency
• Hardware Data Protection Feature
• Serial Peripheral Interface (SPI) Compatible – Modes 0 and 3
• CMOS and TTL Compatible Inputs and Outputs
• Commercial and Industrial Temperature Ranges
Description
The AT45D021 is a 5-volt only, serial interface Flash memory suitable for in-system
reprogramming. Its 2,162,688 bits of memory are organized as 1024 pages of 264-
bytes each. In addition to the main memory, the AT45D021 also contains two data
SRAM buffers of 264-bytes each. The buffers allow receiving of data while a page in
the main memory is being reprogrammed. Unlike conventional Flash memories that
are accessed randomly with multiple address lines and a parallel interface, the
DataFlash uses a serial interface to sequentially access its data. The simple serial
interface facilitates hardware layout, increases system reliability, minimizes switching
(continued)
Pin Configurations
PLCC
Pin Name
CS
SCK
SI
SO
WP
RESET
RDY/BUSY
Function
Chip Select
Serial Clock
Serial Input
Serial Output
Harware Page Write
Protect Pin
Chip Reset
Ready/Busy
RDY/BUSY
RESET
WP
NC
NC
VCC
GND
NC
NC
NC
CS
SCK
SI
SO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TSOP Top View
Type 1
SCK
SI
SO
NC
NC
NC
NC
NC
NC
5
6
7
8
9
10
11
12
13
29 WP
28 RESET
27 RDY/BUSY
26 NC
25 NC
24 NC
23 NC
22 NC
21 NC
Note:
PLCC package pins 16 and 17
are DON’T CONNECT.
PLCC
28 NC
27 NC
26 NC
25 NC
24 NC
23 NC
22 NC
21 NC
20 NC
19 NC
18 NC
17 NC
16 NC
15 NC
GND
NC
NC
CS
SCK
SI
SO
NC
NC
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28 VCC
27 NC
26 NC
25 WP
24 RESET
23 RDY/BUSY
22 NC
21 NC
20 NC
19 NC
18 NC
17 NC
16 NC
15 NC
2-Megabit
5-volt Only
Serial
DataFlash®
AT45D021
Rev. 0869B–07/98
1
|
| |
 
AT45D021
RESET: A low state on the reset pin (RESET) will terminate
the operation in progress and reset the internal state
machine to an idle state. The device will remain in the reset
condition as long as a low level is present on the RESET
pin. Normal operation can resume once the RESET pin is
brought back to a high level.
The device also incorporates an internal power-on reset
circuit; therefore, there are no restrictions on the RESET
pin during power-on sequences.
READY/BUSY: This open drain output pin will be driven
low when the device is busy in an internally self-timed oper-
ation. This pin, which is normally in a high state (through an
external pull-up resistor), will be pulled low during program-
ming operations, compare operations, and during page-to-
buffer transfers.
Absolute Maximum Ratings*
Temperature Under Bias ................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
All Output Voltages
with Respect to Ground .............................-0.6V to VCC + 0.6V
The busy status indicates that the Flash memory array and
one of the buffers cannot be accessed; read and write
operations to the other buffer can still be performed.
Power On/Reset State
When power is first applied to the device, or when recover-
ing from a reset condition, the device will default to SPI
mode 3. In addition, the SO pin will be in a high impedance
state, and a high to low stransition on the CS pin will be
required to start a valid instruction. The SPI mode will be
automatically selected on every falling edge of CS by sam-
pling the inactive clock state.
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
DC and AC Operating Range
AT45D021
Operating Temperature (Case)
Com.
Ind.
0°C to 70°C
-40°C to 85°C
VCC Power Supply(1)
4.5V to 5.5V
Note: 1. After power is applied and VCC is at the minimum specified data sheet value, the system should wait 20 ms before an oper-
ational mode is started.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AT45D021-RI electronic component. |
| Information | Total 18 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ AT45D021-RI.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| AT45D021-RC | The function is 2-Megabit 5-volt Only Serial DataFlash. ATMEL Corporation | |
| AT45D021-RI | The function is 2-Megabit 5-volt Only Serial DataFlash. ATMEL Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AT45
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||