|
|
PDF CS52015-3 Data sheet ( Hoja de datos )
| Número de pieza | CS52015-3 | |
| Descripción | 1.5A/ 3.3V Fixed Linear Regulator | |
| Fabricantes | Cherry Semiconductor Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CS52015-3 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
CS52015-3
1.5A, 3.3V Fixed Linear Regulator
Description
The CS52015-3 linear regulator pro-
vides 1.5A at 3.3V with an output
voltage accuracy of ±1.5%.
The regulator is intended for use as
a post regulator and microprocessor
supply. The fast loop response and
low dropout voltage make this reg-
ulator ideal for applications where
low voltage operation and good
transient response are important.
The circuit is designed to operate
with dropout voltages less than
1.4V at 1.5A output current. The
maximum quiescent current is only
10mA at full load. Device protec-
tion includes overcurrent and ther-
mal shutdown.
The CS52015-3 is pin compatible
with the LT1086 family of linear
regulators but has lower dropout
voltage.
The regulator is available in TO-
220, surface mount D2, and SOT-223
packages.
Features
s Output Current to 1.5A
s Output Accuracy to ±1.5%
Over Temperature
s Dropout Voltage (typical)
1.05V @ 1.5A
s Fast Transient Response
s Fault Protection
Current Limit
Thermal Shutdown
Application Diagram
VIN VOUT
CS52015-3
3.3V
@ 1.5A
Package Options
3L TO-220
Tab (VOUT)
3L D2PAK
Tab (VOUT)
10 mF
5V
Gnd
Rev. 2/17/98
22mF
5V
1
1
1 3L SOT-223
Tab (VOUT)
CS52015 -3
1 Gnd
2 VOUT (tab)
3 VIN
1
Consult factory for other fixed output voltage
options.
Cherry Semiconductor Corporation
2000 South County Trail, East Greenwich, RI 02818
Tel: (401)885-3600 Fax: (401)885-5786
Email: [email protected]
Web Site: www.cherry-semi.com
A ¨ Company
1 page  
Applications Information: continued
VIN VIN
conductor
RC parasitic resistance
VOUT
CS52015-3
RLOAD
Figure 2: Conductor parasitic resistance effects can be minimized with
the above grounding scheme for fixed output regulators.
Calculating Power Dissipation and Heat Sink Requirements
The CS52015-3 linear regulator includes thermal shutdown
and current limit circuitry to protect the device. High
power regulators such as these usually operate at high
junction temperatures so it is important to calculate the
power dissipation and junction temperatures accurately to
ensure that an adequate heat sink is used.
The case is connected to VOUT on the CS52015-3, and elec-
trical isolation may be required for some applications.
Thermal compound should always be used with high cur-
rent regulators such as these.
The thermal characteristics of an IC depend on the follow-
ing four factors:
1. Maximum Ambient Temperature TA (¡C)
2. Power dissipation PD (Watts)
3. Maximum junction temperature TJ (¡C)
4. Thermal resistance junction to ambient RQJA (C/W)
IOUT(max) is the maximum output current, for the application
IQ is the maximum quiescent current at IOUT(max).
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment has a thermal resistance. Like series
electrical resistances, these resistances are summed to
determine RQJA, the total thermal resistance between the
junction and the surrounding air.
1. Thermal Resistance of the junction to case, RQJC (¡C/W)
2. Thermal Resistance of the case to Heat Sink, RQCS (¡C/W)
3. Thermal Resistance of the Heat Sink to the ambient air,
RQSA (¡C/W)
These are connected by the equation:
RQJA = RQJC + RQCS + RQSA
(3)
The value for RQJA is calculated using equation (3) and the
result can be substituted in equation (1).
The value for RQJC is 3.5ûC/W. For a high current regulator
such as the CS52015-3 the majority of the heat is generated
in the power transistor section. The value for RQSA
depends on the heat sink type, while RQCS depends on fac-
tors such as package type, heat sink interface (is an insula-
tor and thermal grease used?), and the contact area
between the heat sink and the package. Once these calcula-
tions are complete, the maximum permissible value of
RQJA can be calculated and the proper heat sink selected.
For further discussion on heat sink selection, see applica-
tion note ÒThermal Management for Linear Regulators.Ó
These four are related by the equation
TJ = TA + PD ´ RQJA
(1)
The maximum ambient temperature and the power dissi-
pation are determined by the design while the maximum
junction temperature and the thermal resistance depend on
the manufacturer and the package type.
The maximum power dissipation for a regulator is:
PD(max)={VIN(max)ÐVOUT(min)}IOUT(max)+VIN(max)IQ
where
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
(2)
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet CS52015-3.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CS52015-1 | 1.5A Adjustable Linear Regulator | Cherry Semiconductor Corporation |
| CS52015-1 | Linear Regulator |  ON Semiconductor |
| CS52015-1GDP3 | 1.5A Adjustable Linear Regulator | Cherry Semiconductor Corporation |
| CS52015-1GDPR3 | 1.5A Adjustable Linear Regulator | Cherry Semiconductor Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |