|
|
PDF CS5203-1GT3 Data sheet ( Hoja de datos )
| Número de pieza | CS5203-1GT3 | |
| Descripción | 3A Adjustable Linear Regulator | |
| Fabricantes | Cherry Semiconductor Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CS5203-1GT3 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
CS5203-1
3A Adjustable Linear Regulator
Description
The CS5203-1 linear regulator pro-
vides 3A at adjustable output volt-
ages with an accuracy of ±1.5%.
The device uses two external resis-
tors to set the output voltage with-
in a 1.25V to 5.5V range.
The regulator is intended for use as
a post regulator and microproces-
sor supply. The fast loop response
and low dropout voltage make this
regulator ideal for applications
where low voltage operation and
good transient response are impor-
tant.
The circuit is designed to operate
with dropout voltage less than 1.4V
at 3A output current. Device pro-
tection includes overcurrent and
thermal shutdown.
The CS5203-1 is pin compatible
with the LT1085 family of linear
regulators but has lower dropout
voltage.
The regulator is available in TO-220
and surface mount D2 packages.
Features
s Output Current to 3A
s Output Accuracy to ± 1.5%
Over Temperature
s Dropout Voltage (typical)
1.2V @ 3A
s Fast Transient Response
s Fault Protection
Current Limit
Thermal Shutdown
Application Diagram
5.0V VIN VOUT
CS5203-1
10mF
5V
Adj
0.1mF
5V
124W
1%
200W
1%
3.3V @ 3A
22mF
5V
Package Options
3L TO-220
Tab (VOUT)
3L D2PAK
Tab (VOUT)
1
1
CS5203 -1
1 Adj
2 VOUT (Tab)
3 VIN
Consult factory for fixed output
voltage versions.
Rev. 9/17/97
Cherry Semiconductor Corporation
2000 South County Trail, East Greenwich, RI 02818
Tel: (401)885-3600 Fax: (401)885-5786
Email: [email protected]
Web Site: www.cherry-semi.com
1 A ¨ Company
1 page  
Applications Information
The CS5203-1 linear regulator provides adjustable volt-
ages at currents up to 3A. The regulator is protected
against overcurrent conditions and includes thermal
shutdown.
The CS5203-1 has a composite PNP-NPN output transistor
and requires an output capacitor for stability. A detailed
procedure for selecting this capacitor is included in the
Stability Considerations section.
Adjustable Operation
The CS5203-1 has an output voltage range of 1.25V to 5.5V.
An external resistor divider sets the output voltage as
shown in Figure 1. The regulator maintains a fixed 1.25V
(typical) reference between the output pin and the adjust
pin.
A resistor divider network R1 and R2 causes a fixed cur-
rent to flow to ground. This current creates a voltage
across R2 that adds to the 1.25V across R1 and sets the
overall output voltage. The adjust pin current (typically
50µA) also flows through R2 and adds a small error that
should be taken into account if precise adjustment of VOUT
is necessary.
The output voltage is set according to the formula:
( )VOUT = VREF ´ R1 + R2 + IAdj ´ R2
R1
The term IAdj ´ R2 represents the error added by the adjust
pin current.
R1 is chosen so that the minimum load current is at least
2mA. R1 and R2 should be the same type, e.g. metal film
for best tracking over temperature. While not required, a
bypass capacitor between the adjust pin and ground will
improve ripple rejection and transient response. A 0.1µF
tantalum capacitor is recommended for Òfirst cutÓ design.
Type and value may then be varied to optimize perfor-
mance vs. price.
ages in excess of 7V. The main considerations in such a
design are power-up and short circuit capability.
In most applications, ramp-up of the power supply to VIN
is fairly slow, typically on the order of several tens of mil-
liseconds, while the regulator responds in less than one
microsecond. In this case, the linear regulator begins
charging the load as soon as the VIN to VOUT differential is
large enough that the pass transistor conducts current. The
load at this point is essentially at ground, and the supply
voltage is on the order of several hundred millivolts, with
the result that the pass transistor is in dropout. As the sup-
ply to VIN increases, the pass transistor will remain in
dropout, and current is passed to the load until VOUT
reaches the point at which the IC is in regulation. Further
increase in the supply voltage brings the pass transistor
out of dropout. The result is that the output voltage fol-
lows the power supply ramp-up, staying in dropout until
the regulation point is reached. In this manner, any output
voltage may be regulated. There is no theoretical limit to
the regulated voltage as long as the VIN to VOUT differen-
tial of 7V is not exceeded.
However, the possibility of destroying the IC in a short
circuit condition is very real for this type of design. Short
circuit conditions will result in the immediate operation of
the pass transistor outside of its safe operating area. Over-
voltage stresses will then cause destruction of the pass
transistor before overcurrent or thermal shutdown circuit-
ry can become active. Additional circuitry may be required
to clamp the VIN to VOUT differential to less than 7V if fail-
safe operation is required. One possible clamp circuit is
illustrated in figure 2; however, the design of clamp cir-
cuitry must be done on an application by application basis.
Care must be taken to ensure the clamp actually protects
the design. Components used in the clamp design must be
able to withstand the short circuit condition indefinitely
while protecting the IC.
EXTERNAL SUPPLY
VIN
C1
VIN VOUT
CS5203-1
Adj
VREF
R1
VOUT
C2
VIN
VOUT
VAdj
VOUT
IAdj
CAdj
R2
Figure 1. Resistor divider scheme.
The 5203-1 linear regulator has an absolute maximum
specification of 7V for the voltage difference between VIN
and VOUT. However, the IC may be used to regulate volt-
Figure 2. Short Circuit Protection Circuit for High Voltage Application.
Stability Considerations
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start-up
delay, load transient response and loop stability.
The capacitor value and type is based on cost, availability,
size and temperature constraints. A tantalum or aluminum
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet CS5203-1GT3.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CS5203-1GT3 | 3A Adjustable Linear Regulator | Cherry Semiconductor Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |