|
|
|
부품번호 | HS-0508RH 기능 |
|
|
기능 | Radiation Hardened Single 8/Differential 4-Channel CMOS Analog Multiplexers | ||
제조업체 | Intersil Corporation | ||
로고 | |||
Data Sheet
HS-0508RH, HS-0509RH
August 1999 File Number 3977.2
Radiation Hardened Single 8/Differential
4-Channel CMOS Analog Multiplexers
These radiation hardened monolithic CMOS multiplexers
each include an array of eight analog switches, a digital
decode circuit for channel selection, a voltage reference for
logic thresholds, and an ENABLE input for device selection
when several multiplexers are present.
The Dielectric Isolation (DI) process used in fabrication of
these devices eliminates the problem of latch-up. Also, DI
offers much lower substrate leakage and parasitic
capacitance than conventional junction-isolated CMOS.
Switches are guaranteed to break-before-make, so that two
channels are never shorted together. The switching
threshold for each digital input is established by an internal
+5V reference, providing a guaranteed minimum 2.4V for
logic “1” and maximum 0.8 for logic “0”. This allows direct
interface without pull-up resistors to signals from most logic
families: CMOS, TTL, DTL and some PMOS. For protection
against transient overvoltage, the digital inputs include a
series 200Ω resistor and a diode clamp to each supply. The
HS-0508RH is an eight channel single-ended multiplexer,
and the HS-0509RH is a four channel differential version. If
input overvoltage protection is needed, the HS-0548RH and
HS-0549RH multiplexers are recommended.
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-95692. A “hot-link” is provided
on our homepage for downloading.
http://www.intersil.com/spacedefense/space.htm
Pinouts
HS-0508RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
A0 1
ENABLE 2
-VSUPPLY 3
IN 1 4
IN 2 5
IN 3 6
IN 4 7
OUT 8
16 A1
15 A2
14 GND
13 +VSUPPLY
12 IN 5
11 IN 6
10 IN 7
9 IN 8
Features
• Electrically Screened to SMD # 5962-95692
• QML Qualified per MIL-PRF-38535 Requirements
• Gamma Dose . . . . . . . . . . . . . . . . . . . . . . 1 x 104RAD(Si)
• No Latch-Up
• No Channel Interaction During Overvoltage
• Low On Resistance . . . . . . . . . . . . . . . . . . . . <200Ω (Typ)
• 44V Maximum Power Supply
• Break-Before-Make Switch
• Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . ±15V
• Access Time. . . . . . . . . . . . . . . . . . . . . . . . . <300ns (Typ)
Applications
• Data Acquisition Systems
• Control Systems
• Telemetry
Ordering Information
ORDERING NUMBER
INTERNAL
MKT. NUMBER
5962D9569201VEA
HS1-0508RH-Q
5962D9569201VEC
HS1B-0508RH-Q
5962D9569202VEA
HS1-0509RH-Q
5962D9569202VEC
HS1B-0509RH-Q
TEMP. RANGE
(oC)
-55 to 125
-55 to 125
-55 to 125
-55 to 125
HS-0509RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
A0 1
ENABLE 2
-VSUPPLY 3
IN 1A 4
IN 2A 5
IN 3A 6
IN 4A 7
OUTA 8
16 A1
15 GND
14 +VSUPPLY
13 IN 1B
12 IN 2B
11 IN 3B
10 IN 4B
9 OUT B
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Burn-In/Life Test Circuits
HS-0508RH, HS-0509RH
F0 1
F3
V1
2
3
D1 C1
4
5
6
7
R1
8
16 F1
15 F2
14
13 V2
12
D2 C2
11
10
9
1
2
V2 3
D1 C1
4
5
6
7
R1
8
V1
16
15
14
13 V3
12
D2 C2
11
10
9
HS-0508RH
DYNAMIC BURN-IN AND LIFE TEST CIRCUIT
V1 = -15V maximum, -16V minimum
V2 = +15V minimum, +16V maximum
R1 = 10kΩ ±5% 1/4W
C1 = C2 = 0.01µF minimum (per socket) or 0.1µF minimum (per row)
D1 = D2 = 1N4002 (or equivalent)
F0 = 100kHz 50% duty cycle; VIL = 0.8V max; VIH = 4.0V min.
F1 = F0/2
F2 = F1/2
F3 = F2/2
HS-0508RH
STATIC BURN-IN TEST CIRCUIT
V1 = 5V minimum, 6V maximum
V2 = -15V maximum, -16V minimum
V3 = +15V minimum, +16V maximum
R1 = 10kΩ ±5% 1/4W
C1 = C2 = 0.01µF minimum (per socket) or 0.1µF minimum (per row)
D1 = D2 = 1N4002 (or equivalent)
V3
D1
F0
F2
C1
R1
1
2
3
4
5
6
7
8
16 F1
15
14 V2
13
D1 C1
12
11
10
9
R1
V3
D1
C1
R1
1
2
3
4
5
6
7
8
16 V1
15
14 V2
13
D1 C1
12
11
10
9
R1
HS-0509RH
DYNAMIC BURN-IN AND LIFE TEST CIRCUIT
V2 = +15.5V, ±.0.5V
V3 = -15.5V, ±0.5V
R1 = 10kΩ, ±5%
C1 = 0.1µF minimum (per socket)
D1 = 1N4002 or equivalent (per board)
F0 = 100kHz, ±10%; F1 = F0/2; F2 = F1/2, 50% duty cycle,
VIL = 0.8V max.; VIH = 4.0V min.
HS-0509RH
STATIC BURN-IN TEST CIRCUIT
V1 = +5.5V, ±0.5V
V2 = +15.5V, ±0.5V
V3 = -15.5V, ±0.5V
R1 = 10kΩ, ±10%
C1 = 0.1µF minimum (per socket)
D1 = 1N4002 or equivalent (per board)
4
4페이지 | |||
구 성 | 총 6 페이지수 | ||
다운로드 | [ HS-0508RH.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
HS-0508RH | Radiation Hardened Single 8/Differential 4-Channel CMOS Analog Multiplexers | Intersil Corporation |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |