|
|
|
부품번호 | HLY-3051 기능 |
|
|
기능 | Series II HLY-3051 VOLTMETER Introduction | ||
제조업체 | ETC | ||
로고 | |||
Series II
HLY-3051 VOLTMETER
Introduction:
The Odyssey Series II gauges from Dakota Digital, Inc. incorporates the reliability and
quality of our standard gauges, along with several unique features and easy mounting. These
features include:
• Industry standard 2-1/16” gauge size.
• Weather-proof construction.
• A warning feature that flashes the gauge readout when outside operating limits.
• User adjustable warning points.
• Microprocessor stabilized readings.
• Quick-Start feature to provide accurate readings quickly after being powered up.
• Night dimming with lens label lighting.
• Non-Glare, high contrast lens.
• High Visibility VFD display for sunlight readability.
Operation:
The PWR terminal should be connected to a 12 volt accessory feed. The case provides
the gauge ground. Connect a ground wire to the screw at the bottom rear of the case. When the
DIM terminal has 12 volts, it will dim the display for night viewing. The SND terminal is the
voltage sensing input. To read the vehicle system voltage, connect this to the PWR terminal.
To read the voltage at a second battery or other remote location, connect a wire from the SND
terminal to the voltage to be monitored.
The voltage gauge will operate in the voltage range of 8.0 – 17.0 and read correct
between the voltage range of 1.0 - 18.0 volts. It has a user adjustable lower and upper warning
level. This can be set to indicate low voltage and overcharging conditions.
Setting the warning limits:
The SND terminal is used to enter and change the warning settings. You will need a
wire connected to the SND terminal that can be powered separate from the gauge.
1. To enter the set mode, turn the key on with the SND wire not powered. The gauge will
display “SEt”.
2. Power the SND wire. The gauge will display “ HI”. (If you wait too long the gauge will
exit the setup routine and you will need to repeat step #1).
3. Release the SND wire. The gauge will display a number between 13.9 and 16.9.
4. Each time you momentarily power the SND wire the number will increase by one.
5. When the desired high warning value is displayed, keep the SND wire powered for about
2 seconds. The gauge will display “ LO”.
6. Release the SND wire. The gauge will display a number between 9.7 and 12.6.
7. Each time you momentarily power the SND wire the number will increase by one.
8. When the desired low warning value is displayed, keep the SND wire powered for about
2 seconds. The gauge will display “--”.
9. Turn the key off.
Technical specifications
Minimum operating voltage -
7 volts
Maximum operating voltage -
17 volts
(operating at or near maximum voltage for an extended time can damage unit)
Gauge Resolution
- 0.1 V
Gauge accuracy
- ±0.1 V
Typical current draw (@ 13.8V) -
0.2 A
ODYSSEY SERIES DIGITAL GAUGE LIMITED WARRANTY
DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under
normal use and condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF
PURCHASE, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts or labor directly
related to repairs of the defect(s).
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of
warranty coverage (e.g. dated bill of sale), name, address, phone number, and specification of defects, transportation prepaid,
to the factory. This Warranty is valid for the original purchaser only and may not be transferred.
This warranty does not cover nor extend to damage to vehicle electrical system. This Warranty does not apply to
any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation,
mishandling, misuse, neglect, or accident.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABLITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability other that expressed
herein in connection with the sale of this product.
The Company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF THE
COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID TO THE
PURCHASER FOR THE PRODUCT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if incidental
or consequential damage so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
3421 Hovland Ave
Sioux Falls, SD 57107
Phone: (605) 332-6513
FAX: (605) 339-4106
4페이지 | |||
구 성 | 총 4 페이지수 | ||
다운로드 | [ HLY-3051.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
HLY-3051 | Series II HLY-3051 VOLTMETER Introduction | ETC |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |