Datasheet.kr   

AT29BV010A-25 데이터시트 PDF




ATMEL Corporation에서 제조한 전자 부품 AT29BV010A-25은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 AT29BV010A-25 자료 제공

부품번호 AT29BV010A-25 기능
기능 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash
제조업체 ATMEL Corporation
로고 ATMEL Corporation 로고


AT29BV010A-25 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 10 페이지수

미리보기를 사용할 수 없습니다

AT29BV010A-25 데이터시트, 핀배열, 회로
AT29BV010A
Features
Single Supply Voltage, Range 2.7V to 3.6V
Single Supply for Read and Write
Software Protected Programming
Fast Read Access Time - 200 ns
•• Low Power Dissipation
15 mA Active Current
20 µA CMOS Standby Current
Sector Program Operation
Single Cycle Reprogram (Erase and Program)
1024 Sectors (128 bytes/sector)
Internal Address and Data Latches for 128-Bytes
Two 8 KB Boot Blocks with Lockout
Fast Sector Program Cycle Time - 20 ms Max.
Internal Program Control and Timer
DATA Polling for End of Program Detection
Typical Endurance > 10,000 Cycles
CMOS and TTL Compatible Inputs and Outputs
•• Commercial and Industrial Temperature Ranges
1 Megabit
(128K x 8)
Single 2.7-volt
Battery-Voltage
CMOS Flash
Description
The AT29BV010A is a 2.7-volt-only in-system Flash Programmable and Erasable
Read Only Memory (Flash). Its 1 megabit of memory is organized as 131,072 words
by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM technol-
ogy, the device offers access times up to 200 ns, and a low 54 mW power dissipation.
When the device is deselected, the CMOS standby current is less than 20 µA. The
device endurance is such that any sector can typically be written to in excess of
10,000 times. The programming algorithm is compatible with other devices in Atmel’s
Low Voltage Flash family of products.
(continued)
Pin Configurations
Pin Name
A0 - A16
CE
OE
WE
I/O0 - I/O7
NC
Function
Addresses
Chip Enable
Output Enable
Write Enable
Data Inputs/Outputs
No Connect
PLCC Top View
AT29BV010A
TSOP Top View
Type 1
0519B
4-3




AT29BV010A-25 pdf, 반도체, 판매, 대치품
Device Operation (Continued)
BOOT BLOCK LOCKOUT DETECTION: A software
method is available to determine whether programming of
either boot block section is locked out. See Software
Product Identification Entry and Exit sections. When the
device is in the software product identification mode, a
read from location 00002H will show if programming the
lower address boot block is locked out while reading loca-
DC and AC Operating Range
tion 1FFF2H will do so for the upper boot block. If the data
is FE, the corresponding block can be programmed; if the
data is FF, the program lockout feature has been activated
and the corresponding block cannot be programmed. The
software product identification exit mode should be used
to return to standard operation.
AT29BV010A-20
AT29BV010A-25
AT29BV010A-30
Operating
Temperature (Case)
VCC Power Supply (1)
Com.
Ind.
0°C - 70°C
2.7V to 3.6V
0°C - 70°C
-40°C - 85°C
2.7V to 3.6V
0°C - 70°C
-40°C - 85°C
2.7V to 3.6V
1. After power is applied and VCC is at the minimum specified data sheet value, the system should wait 20 ms before an
operational mode is started.
Operating Modes
Mode
Read
Program (2)
Standby/Write Inhibit
Program Inhibit
Program Inhibit
Output Disable
Product Identification
Hardware
Software (5)
CE OE WE
VIL VIL VIH
VIL VIH VIL
VIH X (1) X
X X VIH
X VIL X
X VIH X
Ai I/O
Ai DOUT
Ai DIN
X High Z
High Z
VIL
VIL
VIH
A1 - A16 = VIL, A9 = VH (3),
A0 = VIL
A1 - A16 = VIL, A9 = VH (3),
A0 = VIH
Manufacturer Code (4)
Device Code (4)
A0 = VIL, A1 - A16 = VIL
Manufacturer Code (4)
A0 = VIH, A1 - A16 = VIL
Device Code (4)
Notes: 1. X can be VIL or VIH.
2. Refer to AC Programming Waveforms.
3. VH = 12.0V ± 0.5V.
DC Characteristics
4. Manufacturer Code is 1F. The Device Code is 35.
5. See details under Software Product Identification Entry/Exit.
Symbol
ILI
ILO
Parameter
Input Load Current
Output Leakage Current
ISB1 VCC Standby Current CMOS
ISB2 VCC Standby Current TTL
ICC VCC Active Current
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage
VOH Output High Voltage
Condition
VIN = 0V to VCC
VI/O = 0V to VCC
CE = VCC - 0.3V to VCC
Com.
Ind.
CE = 2.0V to VCC
f = 5 MHz; IOUT = 0 mA; VCC = 3.6V
IOL = 1.6 mA; VCC = 3.0V
IOH = -100 µA; VCC = 3.0V
Min
2.0
2.4
Max
1
1
20
50
1
15
0.6
0.45
Units
µA
µA
µA
µA
mA
mA
V
V
V
V
4-6 AT29BV010A

4페이지










AT29BV010A-25 전자부품, 판매, 대치품
Program Cycle Characteristics
Symbol
tWC
tAS
tAH
tDS
tDH
tWP
tBLC
tWPH
Parameter
Write Cycle Time
Address Set-up Time
Address Hold Time
Data Set-up Time
Data Hold Time
Write Pulse Width
Byte Load Cycle Time
Write Pulse Width High
Min
10
100
100
10
200
200
Software Protected Program Waveform
AT29BV010A
Max Units
20 ms
ns
ns
ns
ns
ns
150 µs
ns
Notes: 1. OE must be high when WE and CE are both low.
2. A7 through A16 must specify the sector address
during each high to low transition of WE (or CE)
after the software code has been entered.
Programming Algorithm (1)
LOAD DATA AA
TO
ADDRESS 5555
LOAD DATA 55
TO
ADDRESS 2AAA
LOAD DATA A0
TO
ADDRESS 5555
WRITES ENABLED
LOAD DATA
TO (3)
SECTOR (128 BYTES)
ENTER DATA
(2)
PROTECT STATE
3. All bytes that are not loaded within the sector being
programmed will be indeterminate.
Notes for software program code:
1. Data Format: I/O7 - I/O0 (Hex);
Address Format: A14 - A0 (Hex).
2. Data Protect state will be re-activated at end of program
cycle.
3. 128-bytes of data MUST BE loaded.
4-9

7페이지


구       성 총 10 페이지수
다운로드[ AT29BV010A-25.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AT29BV010A-20

1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash

ATMEL Corporation
ATMEL Corporation
AT29BV010A-20JC

1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash

ATMEL Corporation
ATMEL Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵