Datasheet.kr   

AT29C010A-90PC 데이터시트 PDF




ATMEL Corporation에서 제조한 전자 부품 AT29C010A-90PC은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 AT29C010A-90PC 자료 제공

부품번호 AT29C010A-90PC 기능
기능 1 Megabit 128K x 8 5-volt Only CMOS Flash Memory
제조업체 ATMEL Corporation
로고 ATMEL Corporation 로고


AT29C010A-90PC 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 12 페이지수

미리보기를 사용할 수 없습니다

AT29C010A-90PC 데이터시트, 핀배열, 회로
AT29C010A
Features
Fast Read Access Time - 70 ns
5-Volt-Only Reprogramming
•• Sector Program Operation
Single Cycle Reprogram (Erase and Program)
1024 Sectors (128 bytes/sector)
Internal Address and Data Latches for 128-Bytes
Two 8 KB Boot Blocks with Lockout
Internal Program Control and Timer
Hardware and Software Data Protection
Fast Sector Program Cycle Time - 10 ms
DATA Polling for End of Program Detection
•• Low Power Dissipation
50 mA Active Current
100 µA CMOS Standby Current
Typical Endurance > 10,000 Cycles
•• Single 5V ±10% Supply
CMOS and TTL Compatible Inputs and Outputs
•• Commercial and Industrial Temperature Ranges
1 Megabit
(128K x 8)
5-volt Only
CMOS Flash
Memory
Description
The AT29C010A is a 5-volt-only in-system Flash programmable and erasable read
only memory (PEROM). Its 1 megabit of memory is organized as 131,072 words by 8
bits. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device
offers access times to 70 ns with power dissipation of just 275 mW over the commer-
cial temperature range. When the device is deselected, the CMOS standby current is
less than 100 µA. The device endurance is such that any sector can typically be writ-
ten to in excess of 10,000 times.
To allow for simple in-system reprogrammability, the AT29C010A does not require
high input voltages for programming. Five-volt-only commands determine the opera-
Pin Configurations
Pin Name Function
A0 - A16 Addresses
CE Chip Enable
OE Output Enable
WE Write Enable
I/O0 - I/O7 Data Inputs/Outputs
NC No Connect
DIP Top View
(continued)
AT29C010A
PLCC Top View
TSOP Top View
Type 1
0394B
4-129




AT29C010A-90PC pdf, 반도체, 판매, 대치품
Device Operation (Continued)
BOOT BLOCK LOCKOUT DETECTION: A software
method is available to determine whether programming of
either boot block section is locked out. See Software Prod-
uct Identification Entry and Exit sections. When the device
is in the software product identification mode, a read from
location 00002 will show if programming the lower address
boot block is locked out while reading location FFFF2 will
DC and AC Operating Range
do so for the upper boot block. If the data is FE, the corre-
sponding block can be programmed; if the data is FF, the
program lockout feature has been activated and the corre-
sponding block cannot be programmed. The software
product identification exit mode should be used to return to
standard operation.
Operating
Temperature (Case)
Com.
Ind.
VCC Power Supply
Operating Modes
AT29C010A-70
0°C - 70°C
5V ± 5%
AT29C010A-90
0°C - 70°C
-40°C - 85°C
5V ± 10%
AT29C010A-12
0°C - 70°C
-40°C - 85°C
5V ± 10%
AT29C010A-15
0°C - 70°C
-40°C - 85°C
5V ± 10%
Mode
Read
Program (2)
5V Chip Erase
Standby/Write Inhibit
Program Inhibit
Program Inhibit
Output Disable
Product Identification
Hardware
CE OE
VIL VIL
VIL VIH
VIL VIH
VIH X (1)
XX
X VIL
X VIH
VIL VIL
Software (5)
Notes: 1. X can be VIL or VIH.
2. Refer to AC Programming Waveforms.
3. VH = 12.0V ± 0.5V.
DC Characteristics
WE Ai I/O
VIH Ai DOUT
VIL Ai DIN
VIL Ai
X X High Z
VIH
X
X High Z
VIH
A1 - A16 = VIL, A9 = VH, (3)
A0 = VIL
A1 - A16 = VIL, A9 = VH, (3)
A0 = VIH
Manufacturer Code (4)
Device Code (4)
A0 = VIL
Manufacturer Code (4)
A0 = VIH
Device Code (4)
4. Manufacturer Code: 1F, Device Code: D5
5. See details under Software Product Identification Entry/Exit.
Symbol
ILI
ILO
Parameter
Input Load Current
Output Leakage Current
ISB1 VCC Standby Current CMOS
ISB2
ICC
VIL
VIH
VOL
VOH1
VOH2
VCC Standby Current TTL
VCC Active Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output High Voltage CMOS
Condition
VIN = 0V to VCC
VI/O = 0V to VCC
CE = VCC - 0.3V to VCC
CE = 2.0V to VCC
f = 5 MHz; IOUT = 0 mA
Com.
Ind.
IOL = 2.1 mA
IOH = -400 µA
IOH = -100 µA; VCC = 4.5V
Min Max Units
10 µA
10 µA
100 µA
300 µA
3 mA
50 mA
0.8 V
2.0 V
.45 V
2.4 V
4.2 V
4-132 AT29C010A

4페이지










AT29C010A-90PC 전자부품, 판매, 대치품
Program Cycle Characteristics
Symbol
tWC
tAS
tAH
tDS
tDH
tWP
tBLC
tWPH
Parameter
Write Cycle Time
Address Set-up Time
Address Hold Time
Data Set-up Time
Data Hold Time
Write Pulse Width
Byte Load Cycle Time
Write Pulse Width High
Program Cycle Waveforms (1, 2, 3)
Min
0
50
35
0
90
100
AT29C010A
Max Units
10 ms
ns
ns
ns
ns
ns
150 µs
ns
Notes: 1. A7 through A16 must specify the sector address
during each high to low transition of WE (or CE).
2. OE must be high when WE and CE are both low.
3. All bytes that are not loaded within the sector being
programmed will be indeterminate.
4-135

7페이지


구       성 총 12 페이지수
다운로드[ AT29C010A-90PC.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AT29C010A-90PC

1 Megabit 128K x 8 5-volt Only CMOS Flash Memory

ATMEL Corporation
ATMEL Corporation
AT29C010A-90PI

1 Megabit 128K x 8 5-volt Only CMOS Flash Memory

ATMEL Corporation
ATMEL Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵