Datasheet.kr   

LX1710CDB 데이터시트 PDF




Microsemi Corporation에서 제조한 전자 부품 LX1710CDB은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 LX1710CDB 자료 제공

부품번호 LX1710CDB 기능
기능 EVALUATION KIT
제조업체 Microsemi Corporation
로고 Microsemi Corporation 로고


LX1710CDB 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 18 페이지수

미리보기를 사용할 수 없습니다

LX1710CDB 데이터시트, 핀배열, 회로
LXE1710 EVALUATION BOARD
USER GUIDE
 
   
 

A MICROSEMI COMPANY
Copyright © 2000
Rev. 1.1, 2000-12-01
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1




LX1710CDB pdf, 반도체, 판매, 대치품
LXE1710 EVALUATION BOARD
USER GUIDE
Part Number
LX1710CDB
LX1711CDB
LXE1710
Product
AudioMAX High
Fidelity Controller IC
AudioMAX High
Power Controller IC
LX1710 AudioMAX
Evaluation Board
Description
VDD = 7V to 15V, Switching Class-D Mono
Power Amplifier IC, 28-Pin SSOP Package.
VDD = 7V to 25V, Switching Class-D Mono
Power Amplifier IC, 28-Pin SSOP Package.
Fully Operational Mono Audio Amplifier.
LX1710/1711 AUDIOMAX EVALUATION BOARD FEATURES AND CIRCUIT DESCRIPTION
Fully Assembled Mono Evaluation Board with
LX1710 Class-D Controller IC
Improved SNR and Noise Floor Performance
Output Power of 25W typical (LX1710, 15VDD,
  
Output Power of 54W typical (LX1711, 25VDD,
  
The AudioMAX Evaluation Amplifier Board allows the
user to quickly connect and evaluate the LX1710
Switching Class-D Mono Controller IC. Easy-to-
connect terminal blocks and an RCA plug are
provided for interfacing to Power, Speaker, and Audio
Input connections. The single stage output filter has
been configured to drive a 4    
audio bandwidth amplification (See Application
section LC filter design for component selection,
calculations, and suggested inductor and capacitor
values for other loads). The LXE1710 Evaluation
Board operates from a single supply voltage.
The Class-D Amplifier Controller IC requires a
minimal number of external components to create a
complete amplifier solution. See LXE1710 Evaluation
Board Schematic and Bill of Materials for circuit
specifics. A Class-D Amplifier is a “switching”
amplifier that converts a low-level, analog audio input
signal into a high power, pulse-width modulated
(PWM) output. The switching frequency (500kHz
typical but can be adjusted) is much higher than the
audio bandwidth (20Hz to 20kHz), and is easily
filtered out with a simple LC filter. The support
circuitry can be generally grouped into three areas
(input circuit, output power stage, and output filter).
INPUT COMPENSATION
The first group is the compensation network and
control setting components. These resistors and
Supports Full Audio Bandwidth
     
Terminal Block Connectors for Supply
Voltage and Speaker Connection
RCA Plug for Audio Input Signal
capacitors set up the controller operating frequency,
response characteristics, and comparator ramp
fundamental to Class-D operation.
OUTPUT STAGE
The next section is the output stage. The controller
IC generates a PWM output by controlling external
FETs connected in a full bridge configuration. The full
bridge configuration is connected between the single
supply voltage (PVDD) and ground (PGND) with the
output of the bridge driving the LC filter stage.
Because the FETs are either fully “on” or fully “off”,
Class-D topology is extremely efficient (up to 85%
typical), circuit power dissipation is minimal, and
maximum power is delivered to the speaker. The
bridge output also drives the RC low pass filter, which
provides the feedback for the control loop through the
FBK+ and FBK- inputs.
FILTER STAGE
The single stage, second order LC filter is used to
remove the switching frequency. The frequency
response and corner frequency can be easily
adjusted for optimization of various loads. The LC
evaluation board component values have been
chosen for a 4 !  "  #  $
for component selection.
Copyright © 2000
Rev. 1.1, 2000-12-01
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4

4페이지










LX1710CDB 전자부품, 판매, 대치품
LXE1710 EVALUATION BOARD
ELECTRICAL CHARACTERISTICS
USER GUIDE
Unless otherwise specified, the following specifications apply over the operating ambient temperature 0°C<TA<70°C.
For test circuit, see LXE1710 Evaluation Board Schematic diagram.
PARAMETER
Supply Voltage LX1710
Supply Current
Quiescent Current
Output Power
Efficiency
Total Harmonic Distortion Plus
Noise
Signal-To-Noise Ratio
Power Supply Rejection Ratio
SYMBOL
VDD
IDD
IQ
PO
THD+N
SNR
PSRR
TEST CONDITIONS
VIN=15V, PO=38W, RL
THD+N=1%
VIN=15V, No Input
VIN=15V, RL   
10Hz to 22kHz
VIN=15V, RL   
10Hz to 22kHz
VIN=15V, RL   
10Hz to 22kHz
VIN=15V, fIN=1kHz, PO=10W
VIN=15V, fIN=1kHz, PO=20W
fIN=1kHz, PO=1W
fIN=20Hz to 20kHz, PO=1W
VIN=15V, VRIPPLE=1VRMS,
10Hz to 10kHz
MIN.
7
TYP.
3
43
14
25
38
82
85
0.05
81
-70
MAX
15
0.3
UNITS
V
A
mA
W
W
W
%
%
%
%
dBV
dB
Copyright © 2000
Rev. 1.1, 2000-12-01
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 7

7페이지


구       성 총 18 페이지수
다운로드[ LX1710CDB.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LX1710CDB

EVALUATION KIT

Microsemi Corporation
Microsemi Corporation
LX1710CDB

Class-D Mono Power Amplifier Controller IC

Microsemi Corporation
Microsemi Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵