Datasheet.kr   

E647ATF 데이터시트 PDF




Semtech Corporation에서 제조한 전자 부품 E647ATF은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 E647ATF 자료 제공

부품번호 E647ATF 기능
기능 Pin Electronics Driver/ Window Comparator/ and Switch Matrix
제조업체 Semtech Corporation
로고 Semtech Corporation 로고


E647ATF 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 13 페이지수

미리보기를 사용할 수 없습니다

E647ATF 데이터시트, 핀배열, 회로
EDGE HIGH-PERFORMANCE PRODUCTS
Description
Edge647
Pin Electronics Driver, Window
Comparator, and Switch Matrix
Applications
The Edge647 is an integrated trinary driver, window • Low Cost Automatic Test Equipment
comparator, and switch matrix pin electronics solution
manufactured in a wide voltage CMOS process. It is
designed for automatic test equipment and
instrumentation where cost, functional density, and power
are all at a premium.
The tristatable driver is capable of generating 3 levels -
one for a logic high, one for a logic low, and one for either
a termination voltage or a special programming voltage.
The on-board window comparator effectively determines
whether the DUT is in a high, low, or intermediate state. Functional Block Diagram
The switches are included to allow such functions as PMU,
pull up, and pull down connections.
VH VTT VL
The Edge647 is intended to offer an extremely low leakage,
low cost, low power, small footprint, per pin solution for
100 MHz and below pin electronics applications. It is a
higher performance, pin and functionally compatible
version of the Edge646.
DATA
DATA*
DVR EN
DVR EN*
VTT EN
VTT EN*
SW0
DOUT
Features
• Pin Compatible with the Edge646
• 100 MHz Operation
• 12V I/O Range
• Programmable Output Levels
• Flex In digital Inputs (Technology Independent)
• Three Level Driver
• Extremely Low Leakage Currents (~0 nA)
• Small Footprint (32 Pin, 7 mm X 7 mm,
TQFP Package)
SW0 EN*
SW1
SW1 EN*
SW2
SW2 EN*
VBB
COMPA
HIGH LEVEL
LOW LEVEL
COMPB
LOAD
CVA
VINP
CVB
Revision 2 / October 27, 2000
1
www.semtech.com




E647ATF pdf, 반도체, 판매, 대치품
Edge647
EDGE HIGH-PERFORMANCE PRODUCTS
Circuit Description
Driver Description
The Edge647 driver supports three distinct programmable
driver levels; high, low, and termination, and high
impedance. There are no restrictions between any of these
three levels in that all three may vary independently over
the entire operating voltage range between VCC and VEE.
The DVR EN*, DATA, and VTT EN pins are digital inputs
that control the driver (see Table 1). With DVR EN* low,
DATA determines whether the driver will force VH or VL at
DOUT. With DVR EN* high, VTT EN* controls whether the
driver goes into high impedance or drives VTT.
the DUT. In this environment, the driver can withstand a
short to any legal DUT voltage for an indefinite period.
In a low impedance application with no additional output
series resistance, care must be exercised and systems
should be designed to check for this condition and tristate
the driver if a short is detected.
The driver does NOT have on-chip short circuit protection
or limitation circuitry.
VBB
DVR EN*
1
1
0
0
VTT EN
0
1
X
X
DATA
X
X
0
1
DOUT
HiZ
VTT
VL
VH
VBB is an analog input which establishes the threshold
for all single ended digital input signals. If SW0 EN*,
SW1 EN*, or SW2 EN* are more positive than VBB, these
inputs are a digital “1". Conversely, if they are more
negative than VBB, they are a “0".
Table 1. Driver Truth Table
VH, VL, and VTT
VH, VL, and VTT define the logical “1”, “0”, and
“termination” levels of the driver and can be adjusted
anywhere over the range spanned by VCC to VEE. There
is no restriction between VH, VL, and VTT, in that they can
all vary independently over the entire voltage range
determined by the power supply levels.
All digital inputs are wide voltage comparator inputs, so
they are technology independent. By establishing the
appropriate VBB level for the switch control inputs, and
the appropriate differential input levels for the driver digital
control inputs, the Edge647 may be driven by TTL, ECL,
CMOS, or any custom level circuitry.
SW0 EN*
SW1 EN*
The VH, VL, and VTT inputs are unbuffered in that they
also provide the driver output current, so the sources of
these voltages must have ample current drive capability.
While VTT is referred to as the termination voltage, it may
also be used as a very high “programming” level on many
memory devices.
Driver Output Protection
SW2 EN*
VBB
Figure 1. Driver Digital Inputs
DATA
DATA*
DVR EN*
DVR EN
The Edge647 is designed to operate in a functional testing
environment where a controlled impedance (typically 50
) is maintained between the pin electronics and the DUT.
In general, there will be an external resistor at the driver
output which series terminates the transmission line to
VTT EN
VTT EN*
Figure 2. Driver Differential Digital Inputs
2000 Semtech Corp.
4
www.semtech.com

4페이지










E647ATF 전자부품, 판매, 대치품
EDGE HIGH-PERFORMANCE PRODUCTS
Package Information
TOP VIEW
4
D
D/2
3b
e
N / 4 TIPS
0.20 C A – B
4X
D
E4
E/2
SEE DETAIL "A"
BOTTOM VIEW
57
D1
E1 / 2
D1 / 2
5 7 E1
OO
4 X 0.20 H A – B D
2000 Semtech Corp.
7
Edge647
www.semtech.com

7페이지


구       성 총 13 페이지수
다운로드[ E647ATF.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
E647ATF

Pin Electronics Driver/ Window Comparator/ and Switch Matrix

Semtech Corporation
Semtech Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵