Datasheet.kr   

BA3935 데이터시트 PDF




ROHM Semiconductor에서 제조한 전자 부품 BA3935은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 BA3935 자료 제공

부품번호 BA3935 기능
기능 Reference voltage power supply
제조업체 ROHM Semiconductor
로고 ROHM Semiconductor 로고


BA3935 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 8 페이지수

미리보기를 사용할 수 없습니다

BA3935 데이터시트, 핀배열, 회로
Regulator ICs
Reference voltage power supply
BA3935
The BA3935 is a monolithic reference voltage power supply IC for use in CD radio cassette players.
FApplications
CD radio cassette players, mini-component stereo audio systems
FFeatures
1) With 9V output for audio power supply, 5V output for
microcontrollers, 5V output for radio, 5 and 7.5V out-
puts for CD players, 9.5V output for motor drivers, the
IC is best suited for CD radio cassette players.
2) Precise power supply (5V ± 0.1V) can be obtained by
using external reference voltage input (only AUDIO
output has an internal reference voltage system).
FBlock diagram
3) Zero standby current. (Type.)
4) Output current limit circuit protects the IC against
short-circuiting damage.
5) Compact SIP-M12 package allows a large power dis-
sipation (3W : no heat sink).
6) Thermal protection circuit prevents heat damage to
the IC.
167




BA3935 pdf, 반도체, 판매, 대치품
Regulator ICs
FElectrical characteristics (unless otherwise noted, Ta = 25_C and VCC = 16.0V)
BA3935
170

4페이지










BA3935 전자부품, 판매, 대치품
Regulator ICs
FOperation notes
(1) Operating power supply voltage
When operating within proper ranges of power supply
voltage and ambient temperature, most circuit functions
are guaranteed. Although the rated values of electrical
characteristics cannot be absolutely guaranteed, char-
acteristic values do not change drastically within the
proper ranges.
(2) Power dissipation (Pd)
Refer to the heat reduction characteristics (Fig. 1) and
the rough estimation of IC power dissipation given on a
separate page. Make sure to use the IC within the allow-
able power dissipation with a sufficient margin.
(3) Preventing oscillation at each output and installing
a ripple filter capacitor
To stop oscillation of output, make sure to connect a ca-
pacitor between GND and each of the AUDIO 9V (pin 1),
RADIO (pin 4), COM (pin 5), CD 5V (pin 6), CD 7.5V (pin
7), and MOTOR 9.5V (pin 11) output pins. We recom-
mend using a tantalum electrolytic capacitor having a ca-
pacitance of 10µF or greater (100µF or greater for AU-
DIO 9V) with minimal temperature susceptibility. Also,
sudden deterioration of the AUDIO 9V ripple rejection
during a power drop can be prevented by connecting a
capacitor (220µF or greater recommended) to the C pin
(pin 2).
(4) Overcurrent protection circuit
An overcurrent protection circuit is installed on the AU-
DIO 9V (pin 1), RADIO (pin 4), COM (pin 5), CD 5V (pin
6), CD 7.5V (pin 7), and MOTOR 9.5V (pin 11) outputs,
based on the respective output current. This prevents IC
destruction by overcurrent, by limiting the current with a
curve shape of “7” in the voltage-current graph. The IC
is designed with margins so that current flow will be re-
stricted and latching will be prevented even if a large cur-
rent suddenly flows through a large capacitor. Note that
these protection circuits are only good for preventing
damage from sudden accidents. Make sure your design
does not cause the protection circuit to operate continu-
ously under transitional conditions (for instance, if output
is clamped at 1VF or higher, short mode circuit operates
at 1VF or lower).
BA3935
(5) Reference voltage
Because output voltage is dependent on the input refer-
ence voltage, unstable input results in output wavering
and degradation of ripple rejection. Take care when set-
ting the reference voltage power supply. Note that the
AUDIO output, which has a built-in reference voltage
system, is not affected by the external reference voltage.
(6) Thermal protection circuit
A built-in thermal protection circuit prevents thermal
damage to the IC. All outputs except VDD are switched
OFF when the circuit operates, and revert to the original
state when temperature drops to a certain level.
(7) Grounding
Each ground line in the application circuit must be ade-
quately short regarding the PREGND (pin 3) and GND
(pin 12) pins. Make sure to arrange the ground lines, the
AUDIO system, and other outputs in a pattern that pre-
vents electric interference.
173

7페이지


구       성 총 8 페이지수
다운로드[ BA3935.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
BA3932

Reference voltage power supply

ROHM Semiconductor
ROHM Semiconductor
BA3933

Reference voltage power supply

ROHM Semiconductor
ROHM Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵