Datasheet.kr   

PE-65861 데이터시트 PDF




Pulse에서 제조한 전자 부품 PE-65861은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PE-65861 자료 제공

부품번호 PE-65861 기능
기능 Pulse Transformers T1/E1 XFMR/DUAL/ BH
제조업체 Pulse
로고 Pulse 로고


PE-65861 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 8 페이지수

미리보기를 사용할 수 없습니다

PE-65861 데이터시트, 핀배열, 회로
T1/CEPT/ISDN-PRI TRANSFORMERS
Dual Surface Mount, 1500 Vrms, Extended
and Standard Temperature Range
Dual SMT package contains both transmit and receive transformers
Models matched to leading transceiver ICs
Isolation voltage: 1500 Vrms
UL 1459 and UL 1950 recognized
EN 60950 safety agency approval per BABT
Lead-Free versions available upon request
Electrical Specifications @ 25°C
Part Number
Turns Ratio B
(Pri:Sec ± 2%)
OCL @ 25°C
(mH MIN)
LL
(µH MAX)
CW/W
(pF MAX)
DCR Pri
(MAX)
DCR Sec
(MAX)
Package/ Primary
Schematic
Pins
EXTENDED TEMPERATURE RANGE MODELS1 – OPERATING TEMPERATURE -40°C TO +85°C
PE-68841
1CT:2CT & 1CT:2CT
1.20 & 1.20 0.80 & 0.80
PE-68822
1CT:2CT & 1:1.36CT
1.60 & 1.60 1.00 & 0.80
PE-68825
1:1.15CT & 1CT:2CT
1.60 & 1.60 0.80 & 0.80
PE-68826 E
1:1/1.26 & 1:2CT
1.20 & 1.20 0.80 & 0.80
PE-68827
1:1CT & 2:1
1.60 & 1.60 1.30 & 1.30
PE-68828
1CT:1CT & 1CT:1CT
1.20 & 1.20 0.80 & 0.80
PE-68874
1CT:1.15CT & 1CT:1.15CT
1.20 & 1.20 0.80 & 0.80
PE-68877
1CT:1CT & 1CT:2CT
1.20 & 1.20 0.80 & 0.80
PE-68882
1CT:1.15CT & 1CT:1CT
1.60 & 1.60 0.80 & 0.80
PE-68884
1CT:1.36CT & 1CT:1.36CT
1.20 & 1.20 0.80 & 0.80
PE-68887
1CT:1.41CT & 1CT:1.41CT
1.20 & 1.20 0.80 & 0.80
PE-68881
1CT:2.3CT & 1CT:2CT
1.20 & 1.20 0.80 & 0.80
TX1277
1CT:1CT & 1CT:2CT
1.20 & 1.20 0.80 & 0.80
STANDARD TEMPERATURE RANGE MODELS – OPERATING TEMPERATURE 0°C TO +70°C
T1131 I
1CT:1 & 1:1.36CT
0.70 & 0.70 0.70 & 0.70
PE-68861
1CT:2CT & 1CT:2CT
1.20 & 1.20 0.60 & 0.60
PE-68862
1CT:2CT & 1:1.36CT
1.20 & 1.20 0.60 & 0.80
PE-68863
1:2CT & 1:1.14CT
1.20 & 1.20 0.55 & 0.80
PE-68864 A
1CT:2CT & 1:1
1.20 & 1.20 0.30-0.55 & 0.80
PE-68865
1:1.15CT & 1CT:2CT
1.50 & 1.20 0.80 & 0.60
PE-68866 E
1:1/1.26 & 1:2CT
1.50 & 1.20 0.40 & 0.50
PE-68869
1CT:2CT & 1:1.08CT
1.20 & 1.20 0.60 & 0.60
PE-68836 E
1:1/1.26 & 1:1/1.26
1.50 & 1.50 0.40 & 0 .40
50 & 50
60 & 55
60 & 50
50 & 60
55 & 40
50 & 50
50 & 50
50 & 50
60 & 60
50 & 50
50 & 50
60 & 50
50 & 50
20 & 20
35 & 35
35 & 37
40 & 35
30 & 30
35 & 35
40 & 40
40 & 30
45 & 45
1.00 & 1.00
1.70 & 1.70
1.00 & 1.00
1.00 & 1.00
1.10 & 1.10
1.00 & 1.00
1.20 & 1.20
1.00 & 1.00
1.20 & 1.20
1.20 & 1.20
1.40 & 1.40
1.20 & 1.20
1.00 & 1.00
1.70 & 1.70
2.00 & 1.70
1.20 & 2.00
1.10 & 1.70
1.10 & 0.70
1.00 & 1.00
1.40 & 1.40
1.00 & 1.80
1.40 & 1.20
1.40 & 1.40
1.20 & 1.20
2.10 & 2.10
1.00 & 1.80
0.25 & 0.50
0.70 & 0.70
0.70 & 0.70
0.70 & 0.70
0.70 & 0.70
0.70 & 0.70
0.70 & 0.70
0.70 & 0.70
0.80 & 0.80
0.80 & 0.40
1.20 & 1.20
1.20 & 0.90
1.20 & 0.90
1.20 & 0.70
0.90 & 1.20
0.90 & 1.20
1.10 & 0.90
1.00 & 1.00
AN/2
AN/1
AN/4
AN/5
AN/6
AN/2
AN/2
AN/2
AN/2
AN/2
AN/2
AN/2
AN/2
AN/7
AN/2
AN/1
AN/5
AN/3
AN/4
AN/5
AN/1
AN/7
12-10, 4-6
12-10, 4-6
12-10, 4-6
12-10, 4-6
1-3, 4-6
1-3, 4-6
1-3, 4-6
1-3, 4-6
12-10, 4-6
1-3, 4-6
12-10, 9-7
10-12, 4-6
1-3, 4-6
1-3, 9-7
12-10, 4-6
12-10, 4-6
12-10, 4-6
1-3, 5-6
12-10, 4-6
12-10, 4-6
12-10, 4-6
12-10, 9-7
NOTE: For Quad Surface Mount packages, refer to data sheet T615. For Reinforced Insulation Models, refer to data sheet T617. For Octal Surface Mount packages, refer to data sheet T622.
(See Pages 6 and 7 for Table Notes)
Mechanical
Schematics
AN
1.677,155MAX
12X
.030
0,76
.120
3,05
.050
1,27
TYP
1
12 11 10 9 8 7
2
12 11 10 9 8 7
3
12 11 10 8
7
1.56,0204MAX
12 7
PE-XXXXX
1 DATE CODE 6
.456
11,58
MAX
.100
.085 2,54
2,16
.640 .400
16,26 10,16
.500
12,70
.100
2,54
TYP
SUGGESTED PAD LAYOUT
123 4 6 123 456
1235
6
4 56
12 10 9 8 7 12 10 9 8 7 12 11 10 9
7
7 12 10 9
7
.004/0,10 MAX
.340
8,64
MAX
.010 / .020
0,25 / 0,51
.040 / .050
1,02 / 1,27
0°-8°
1 2 34 5 6 1 2 34
61
Weight . . . . . . . . . . . . . .4.0 grams
Tape & Reel . . . . . . . . . . . .250/reel
Tube . . . . . . . . . . . . . . . . . .30/tube
34 6 1 2 34 56
Dimensions: Inches
mm
Unless otherwise specified,
all tolerances are ± .010
0,25
US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 6287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com
1 T608.R (11/04)




PE-65861 pdf, 반도체, 판매, 대치품
T1/CEPT/ISDN-PRI TRANSFORMERS
Single Through Hole, 1500 Vrms
Extended and standard temperature range
Dual and single through hole models available
Models matched to leading transceiver ICs
Most models UL and BABT recognized
Isolation Voltage: 1500 Vrms MIN
Lead-Free versions available upon request
Electrical Specifications @ 25°C
Part Number
Turns Ratio B
(Pri:Sec ±5%)
OCL @ 25°C
CW/W
(mH MIN) (pF MAX)
LL
(µH MAX)
DCR Pri
(MAX)
STANDARD TEMPERATURE RANGE SINGLE TRANSFORMERS – OPERATING TEMPERATURE 0°C TO +70°C
PE-64931 G
1:1:1 (1:2CS)
1.20 25 0.50
0.70
PE-64933
1CT:3CT
1.20 30 0.50 0.70
PE-64934
1:1
1.20 25 0.50 0.70
PE-64936
1CT:1
1.20 25 0.80 0.70
PE-64937
1:1.36
1.20 35 0.80 0.70
PE-64940
PE-64941 D
1.26CS:1 (1:1:1.58)
1CS:1
0.30 30 0.60 0.80
0.80 30 0.60 0.80
PE-64942
PE-64943 A
PE-65351 G
1CS:1.31
1CT:2CT
1:2CT
0.80 30 0.40 0.80
1.20
30
0.30-0.55
0.70
1.20 40 0.50 0.70
PE-65363
1:4CT
0.50 40 1.00 0.50
PE-65379
1:1.14CT
1.20 35 0.80 0.70
PE-65388
PE-65389 E
1:1.15CT
1:1/1.26
1.50 35 0.60 0.70
1.50 40 0.40 0.70
PE-65415
1CT:2CT
1.20 30 0.50 0.70
PE-65558
1:2.3CT
1.20 35 0.80 0.70
PE-65586
1:1.36CT
1.20 35 0.80 0.70
PE-65755
1CT:1CT
1.20 25 0.80 0.80
PE-68644
1CT:1
0.70 20 0.70 0.20
PE-68645
1:1.36CT
0.70 20 0.70 0.50
T1054
1:1.5CT
1.20 30 0.60 0.70
T1249
1:1.26CT
1.20 60 0.80 0.90
EXTENDED TEMPERATURE RANGE SINGLE TRANSFORMERS 1 – OPERATING TEMPERATURE -40°C TO +85°C
PE-65340
1:1.36
1.20 35 0.80 0.90
PE-65770
1:1.15CT
1.50 40 0.80 0.90
PE-65771
1CT:2CT
1.20 50 0.60 1.00
PE-65778
1CT:1CT
1.20 40 1.00 1.00
PE-68600
PE-68664 E
1CT:3CT
1:1/1.26
1.20 60 0.80 0.90
1.50 50 0.80 0.90
TX1252
1CT:1
1.20 40 1.00 1.00
DCR Sec
(MAX)
0.70 & 0.70
1.60
0.70
0.70
0.80
0.60
0.60
0.60
1.20
1.30
1.50
0.80
0.90
0.90
1.20
1.40
0.90
0.80
0.80
0.40
1.00
1.00
1.20
1.00
2.00
1.00
2.70
1.10
1.00
Package/
Schematic
HC/2
HC/4
HC/1
HC/3
HC/1
HC/2
HC/2
HC/2
HC/4
HC/3
HC/5
HC/5
HC/3
HC/3
HC/4
HC/5
HC/5
HC/4
HC/3
HC/5
HC/3
HC/4
HC/1
HC/3
HC/4
HC/4
HC/4
HC/3
HC/3
Primary
Pins
1-2
1-5
1-2
1-5
5-6
1-4
1-4
1-4
1-5
2-6
1-5
1-5
2-6
2-6
1-5
1-5
1-5
1-5
1-5
1-5
2-6
2-6
5-6
2-6
2-6
1-5
1-5
2-6
1-5
Mechanical
(See Pages 6 and 7 for Table Notes)
Schematics
HC
1.520,700MAX
.250
6,35
MAX
56
3 PE-6XXXX 4
1 Date Code 2
.350
8,89
MAX
.130
3,30
.100
2,54
.200
5,08
.400
10,16
Weight . . . . . . . . . 1.2 grams
Tube . . . . . . . . . . . . .60/tube
Notes: Leads are 24 AWG solderable.
Unused pins not provided.
2
1 4 32 1 1 3 5 1 3 5
1
5
65
1
65
2
26
3
2 46
4
246
5
Dimensions: Inches
mm
Unless otherwise specified, all tolerances are ± .010
0,25
US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 6287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com
T608.R (11/04)
4

4페이지










PE-65861 전자부품, 판매, 대치품
T1/CEPT/ISDN-PRI TRANSFORMERS
Application Notes
1. Extended Temperature Range Models — For extended temperature range
transformers (-40°C to +85°C operating temperature range), OCL (Open
Circuit Inductance for the primary winding) is specified at both -40°C and
+25°C. At -40°C, OCL is 600 µH minimum for all low temperature models with
the exception of PE-68827 which is 800 µH minimum and PE-65836 which is
300 µH minimum. All other parameters are specified at +25°C only. Standard
temperature range is 0°C to +70°C.
2. ET Product — All coils have an ET product of 10 V-µsec minimum.
3. Flammability — Materials used in the products are recognized
as UL94-VO approved. Products meet the requirements of IEC 695-2-2
(Needle Flame Test).
4. Balance Characteristics — The transformers meet the requirements for lon-
gitudinal balance of FCC part 68.
5. Common Mode Rejection Ratio — the CMRR for all transformers is better
than 50 dB at 1 MHz. A typical test circuit is shown below.
HP-8751A
P1 P2
50:100
BALUN
XFMR
100:50
BALUN
6. Crosstalk Attenuation — In the dual packages, which contain transmit and
receive transformers side by side, sufficient crosstalk attenuation is achieved
by the inherent characteristics of the toroid cores as well as by their proper
positioning. The crosstalk attenuation is typically 50 dB or better from 100
KHz to 10 MHz. This result was established with the test circuit shown below.
HP-8751A
P1 P2
50:100
BALUN
100
100
XFMR 100:50
BALUN
7. Return Loss — ITU-T G.703 and European national regulatory documents
specify minimum return loss levels. The transformers will allow these limits to
be complied within the situations where they are applicable.
Frequency
50-100 KHz
100 KHz-2 MHz
2-3 MHz
Return Loss
XMIT
9 dB
15 dB
11 dB
REC
12 dB
18 dB
14 dB
8. Surge Voltage Capability – All transformers and chokes
meet surge voltage tests according to the most stringent
regulatory documents when system designs include the proper voltage and
current suppression devices:
Metallic Voltage:
Longitudinal Voltage:
800 V peak, 10/560 µsec
2,400 V peak, 10/700 µsec
9. Isolation Voltage — 100% of transformers are tested during
production to the specified isolation voltage level.
10. Safety Agency Recognition — Parts listed as "Recognized" or "Certified"
meet Underwriter Laboratories, UL 1459 and UL 1950 per file E133523 (S).
British Approvals Board for Telecommunications
BABT BS 6301:1989/BS 415 and BS EN 41003:1991/EN 60 950, supple-
mentary insulation.
CR/0091
PE-64933
PE-64934
PE-64936
PE-64937
PE-64943
PE-65340
PE-65351
PE-65363
PE-65379
PE-65388
PE-65389
PE-65415
PE-65558
PE-65586
PE-65755
PE-65770
PE-65771
PE-65778
PE-68600
PE-68644
PE-68645
PE-68664
Transformers with Reinforced Insulation according to IEC950 series
PE-68630—PE-68788 (page 3) are certified by the
following organizations:
Code Certificate Information
C CSA, C22.2 #950 & #225, Cert. LR 76802-3, reinforced insulation.
T TÜV, EN 60 950/EN 41003, Cert. R9371358, reinforced insulation.
U UL 1459/UL1950, File E133523 (S), reinforced insulation.
B BABT EN41003/EN60950, Cert. CR0079, reinforced insulation.
(Note: Safety Agency approval of surface mount transformers is pending.)
11. General Information — The transformers are specifically designed for use
in 1.544 Mbps (T1), 2.048 Mbps (CEPT) and ISDN Primary rate (PRI) inter-
face applications. They are matched to the majority of the line interface
transceiver ICs currently available. Use of the proper transformer allows the
interface circuit to comply with ITU-T G.703 and other standards regarding
pulse waveform, return loss, and balance.
12. Common Mode Chokes — The “high-frequency” 4-lines common mode
chokes shown in this data sheet provide an effective means of compliance with
national and international regulations on EMI. They are designed to be used in
conjunction with Pulse’s T1/CEPT transformers as shown in the typical appli-
cation below. Crosstalk is typically -70 dB at 1 MHz and -55 dB at 10 MHz.
Typical Application
Transformer
IC
XMiT
Transformer
IC
RCVE
RCVE
Choke
Choke
XMIT
NOTES FROM TABLES (pages 1 through 6):
Part Turns Secondary Turns Secondary G. PE-64931 and PE-65351 are electrically equivalent, but
Number Ratio 1 Pins Ratio 2 Pins
have different schematics. PE-65351 is both UL 1459 and
A. Toleranced leakage inductance: .30 µH min to .55 µH MAX. PE-65837 1:1.08 3-5 1:1.36 1 - 5
B. OCL (primary inductance) and LL (leakage inductance) are PE-65839 1:1
3-5 1:1.26 1 - 5
measured at the primary winding. Turns ratio is specified PE-65866 1:1
2-3 1:1.26 1 - 3
BABT recognized and is recommended for new designs
because the 3S schematic provides greater physical sepa-
ration between the primary and secondary pins.
primary: secondary. (CT = Center Tap; CS = Split Center PE-68646 1:1.58 3-5
1:2 1 - 5 H. PE-68618 and PE-64950: The fault locate winding is (7-8).
Tap).
PE-65389 1:1
3-5 1:1.26 1 - 5 I. Safety Agency approvals pending.
C. To make a 1CT:1 ratio from a 1CT:2CT ratio, use only one PE-65566 1:1
2-3 1:1.26 1 - 3
half of the secondary (2CT) winding.
PE-65568 1:1
2-3 1:1.26 1 - 3 J. The turns ratio of these devices have been designed, in
D. For Reinforced 3kVrms Dual SMT Transformers, refer to
data sheet T617. For Quad SMT Transformers refer to data
sheet T615. For Octal SMT Transformers refer to data
sheet T622.
PE-68866
PE-68826
PE-68664
PE-68836
1:1
1:1
1:1
1:1
2-3
2-3
3-5
2-3/5-6
1:1.26
1:1.26
1:1.26
1:1.26
1-3
1-3
1-5
1-3/4-6
conjunction with semiconductor vendor recommendations,
to allow connections to various terminations (e.g. 75 or 120
with the same transformer). For example T1075 can be
used with the Siemens PEB 2235 to achieve connection to
the 75 or 120 cable. For 75 termination, the PEB 2235
E. Dual Ratio Transformers — These transformers have F. Standard packaging for surface mount “AN” and “LA” pack- requires the following turns ratio: 1:1.57 (Tx) and 1:1.26
tapped secondary windings to provide two turns ratios ages is anti-static tubes. Optional tray packaging can be (Rx) which can be achieved using pins (1-2):(15-16) for Tx
(T/R). Use the entire primary winding and connect the sec- ordered by adding “R” suffix to the part number, (i.e. PE- and (10-11):(5-8) for Rx. For 120 , the following turns
ondary pins listed below to obtain the desired turns ratio:
65857R). Optional Tape & Reel packaging can be ordered ratio are required: 1:2 (Tx) and 1:1 (Rx), which are pins (1-
by adding “T” suffix to the part number, (i.e. PE-65857T).
2):(16-14) for Tx and (9-11):(5-8) for Rx on the T1075.
US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 6287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com
7 T608.R (11/04)

7페이지


구       성 총 8 페이지수
다운로드[ PE-65861.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PE-65861

Pulse Transformers T1/E1 XFMR/DUAL/ BH

Pulse
Pulse

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵