Datasheet.kr   

EL6255 데이터시트 PDF




Elantec Semiconductor에서 제조한 전자 부품 EL6255은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 EL6255 자료 제공

부품번호 EL6255 기능
기능 4-Channel Laser Diode Driver + Oscillator
제조업체 Elantec Semiconductor
로고 Elantec Semiconductor 로고


EL6255 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 2 페이지수

미리보기를 사용할 수 없습니다

EL6255 데이터시트, 핀배열, 회로
EL6255C - Product Brief
4-Channel Laser Diode Driver + Oscillator
Features
• Shrink-small package outline
• Voltage-controlled output current
source to 150 mA per channel,
requiring one external set resistor
per channel
• Current-controlled output current
source to 150 mA per channel
• Rise time = 1.0 ns
• Fall time = 1.1 ns
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500 MHz
• Oscillator to 100 mA pk/pk
• Single +5V supply (±10%)
• Current amplification = 100
• Disable feature for power-up
protection and power savings
• TTL/CMOS control signals
Applications
• DVD drives
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Ordering Information
Part No
EL6255CU
Temp. Range
0°C to +70°C
Package
QSOP-16
Outline #
MDP0040
General Description
The EL6255C is a high-performance four channel laser diode current
amplifier that provides controlled current to a grounded laser diode.
The four amplifiers can provide up to 150 mA per channel of DC or
pulsed current. Channels 2, 3, and 4 must be used as the write chan-
nels, with switching speeds of one nanosecond rise/fall time. All four
channels are summed together at the IOUT output, allowing the user to
create multilevel waveforms in order to optimize laser diode perfor-
mance. The level of the output current is set by an analog voltage
applied to an external resistor which converts the voltage into a current
at the IIN pin (virtually ground). The current seen at this pin is then
amplified by 100X to become a current source at pin IOUT.
An on-chip 500 MHz oscillator is provided to allow current modula-
tion when in the read mode. This is turned on when the OSCEN pin is
held high (floating not recommended). Complete control of amplitude
and frequency is set by two external resistors connected to ground at
pins RFREQ and RAMP (see graphs in this data sheet for further
explanation). The oscillator will also turn off whenever any of the
OUTEN pins for channels 2, 3, and 4 (the write channels) are low (see
truth table).
Output current pulses are enabled when an ‘L’ signal is applied to the
OUTEN pins. No output current flows when OUTEN is ‘H’, and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete IOUT shut-off is also achieved by
holding the ENABLE pin low, which will override the OUTEN con-
trol pins.
Connection Diagram
IINR 1
IIN2 2
RFREQ 3
IIN3 4
IIN4 5
OUTEN2 6
OUTEN3 7
OUTEN4 8
16 VCC
15 VCC
14 IOUT
13 GND
12 RAMP
11 ENABLE
10 OSCEN
9 VCC
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.





구       성 총 2 페이지수
다운로드[ EL6255.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
EL6250C

Split Supply Laser Driver and Oscillator

Elantec Semiconductor
Elantec Semiconductor
EL6250CU

Split Supply Laser Driver and Oscillator

Elantec Semiconductor
Elantec Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵