Datasheet.kr   

EL6273CU PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 EL6273CU
기능 3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
제조업체 Elantec Semiconductor
로고 Elantec Semiconductor 로고 



전체 2 페이지

		

No Preview Available !

EL6273CU 데이터시트, 핀배열, 회로
EL6273C - Product Brief
3-Channel Laser Diode Driver w/Oscillator & APC Amplifier
Features
• “Shrink-Small” Outline Package
• Voltage-controlled output current
source to 140mA per channel,
requiring one external set resistor
per channel
• Current-controlled output current
source to 140mA per channel
• Rise time = 3.0ns
• Fall time = 3.5ns
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA pk/pk
• Single +5V supply (±10%)
• Current amplification = 400X
• Disable feature for power-up
protection and power savings
• TTL/CMOS control signals
• Fast Settling APC Amplifier
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Ordering Information
Part No
EL6273CU
Temp. Range
0°C to +70°C
Package
QSOP-16
Outline #
MDP0040
General Description
The EL6273C is a high-performance three channel laser driver that
provides controlled current to a grounded laser diode. Three amplifiers
can provide up to 140mA per channel of DC or pulsed current. Chan-
nels 2 and 3 should be used as the write channels, with switching
speeds of approximately three nanoseconds rise/fall time. All three
channels are summed together at the IOUT output, allowing the user to
create multilevel waveforms in order to optimize laser diode perfor-
mance. The level of the output current is set by an analog voltage
applied to an external resistor which converts the voltage into a current
at the IIN pin (virtually ground). The current seen at this pin is then
amplified by 400X to become a current source at pin IOUT.
An on-chip 500MHz oscillator is provided to allow output current
modulation when in any mode. This is turned on when the OSCEN pin
is held high. Complete control of amplitude and frequency is set by
two external resistors connected to ground at pins RFREQ and RAMP
(see graphs in this data sheet for further explanation).
Output current pulses are enabled when an ‘L’ signal is applied to the
OUTEN pin. No output current flows when OUTEN is ‘H’, and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete IOUT shut-off is also achieved by
holding the ENABLE pin low, which will override all other control
pins.
The EL6273C also includes a fast settling APC amplifier designed to
interface directly with the front end monitor diode and the sample-
and-hold amplifier for read and write power control. It’s 40MHz band-
width and 150 ns settling time enable up to 8X CD-RW design.
Connection Diagram
1 VOUT
PDIN 16
2 VREF
VCC 15
3 IINR
IOUT 14
4 RFREQ
GND 13
5 IIN2
RAMP 12
6 IIN3
ENABLE 11
7 OUTEN2 OSCEN 10
8 OUTEN3
VCC 9
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.






구       성총 2 페이지
다운로드[ EL6273CU.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

상호 : 아이지 인터내셔날

사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
EL6273C

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier

Elantec Semiconductor
Elantec Semiconductor
EL6273CU

3-Channel Laser Diode Driver w/Oscillator & APC Amplifier

Elantec Semiconductor
Elantec Semiconductor

DataSheet.kr    |   2020   |  연락처   |  링크모음   |   검색  |   사이트맵