Datasheet.kr   

EL6274C PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 EL6274C
기능 4-Ch Laser Diode Driver Oscillator
제조업체 Elantec Semiconductor
로고 Elantec Semiconductor 로고 



전체 2 페이지

		

No Preview Available !

EL6274C 데이터시트, 핀배열, 회로
EL6274C - Product Brief
4-Ch Laser Diode Driver + Oscillator
Features
• Shrink Small Outline Package
• Voltage-controlled output current
source of 140mA per channel,
requiring one external set resistor
per channel
• Current-controlled output current
source of 140mA per channel
• Rise time = 3.0ns
• Fall time = 3.5ns
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA pk/pk
• Single +5V supply (±10%)
• Current amplification = 100
• Disable feature for power-up
protection and power savings
• TTL/CMOS control signals
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Ordering Information
Part No
EL6274CU
Temp. Range
0°C to +70°C
Package
QSOP-24
Outline #
MDP0040
General Description
The EL6274C is a four channel laser diode current amplifier that pro-
vides controlled current to a grounded laser diode. The four amplifiers
can provide 140mA per channel of DC or pulsed current. Channels 2,
3, and 4 should be used as the write channels, with switching speeds of
approximately three nanosecond rise/fall time. All four channels are
summed together at the IOUT output, allowing the user to create multi-
level waveforms in order to optimize laser diode performance. The
level of the output current is set by an analog voltage applied to an
external resistor which converts the voltage into a current at the IIN pin
(virtually ground). The current seen at this pin is then amplified by
100X to become a current source at pin IOUT.
An on-chip 500MHz oscillator is provided to allow output current
modulation when in any mode. This is turned on when the OSCEN pin
is held high. Complete control of amplitude and frequency is set by
two external resistors connected to ground at pins RFREQ and RAMP
(see graphs in this data sheet for further explanation).
Output current pulses are enabled when an ‘L’ signal is applied to the
OUTEN pin. No output current flows when OUTEN is ‘H’, and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete IOUT shutoff is also achieved by hold-
ing the ENABLE pin low, which will override OUTEN control pins.
The external resistors allow the user to accurately and independently
set each amplifier transconductance by applying a voltage to each
resistor, without restriction on the voltage range, thus ensuring broad
voltage DAC compatibility. Alternatively, the IIN pin can be biased
from a current DAC or other current source.
Connection Diagram
GND 1
24 GND
IINR 2
GND 3
IIN2 4
RFREQ 5
IIN3 6
23 VCC
22 VCC
21 IOUT
20 IOUT
19 GND
IIN4 7
OUTENR 8
OUTEN2 9
OUTEN3 10
OUTEN4 11
GND 12
18 RAMP
17 ENABLE
16 OSCEN
15 VCC
14 VCC
13 GND
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.






구       성총 2 페이지
다운로드[ EL6274C.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

상호 : 아이지 인터내셔날

사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
EL6274C

4-Ch Laser Diode Driver Oscillator

Elantec Semiconductor
Elantec Semiconductor
EL6274CU

4-Ch Laser Diode Driver Oscillator

Elantec Semiconductor
Elantec Semiconductor

DataSheet.kr    |   2020   |  연락처   |  링크모음   |   검색  |   사이트맵