Datasheet.kr   

EL6277CU PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 EL6277CU
기능 3-Channel Laser Diode Driver Oscillator
제조업체 Elantec Semiconductor
로고 Elantec Semiconductor 로고 



전체 2 페이지

		

No Preview Available !

EL6277CU 데이터시트, 핀배열, 회로
EL6277C - Product Brief
3-Channel Laser Diode Driver + Oscillator
Features
Ultra-Small Package Outline
High-performance laser diode
driver
Current-controlled output current
source, 100 mA channel R and 2,
200mA channel 3, requiring one
external set resistor per channel
Rise time = 3.0 ns
Fall time = 3.5ns
On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
Oscillator to 500 MHz
Oscillator to 100 mA pk/pk
Single +5V supply (±10%)
Current amplification = 100
Disable feature for power-up
protection and power savings
TTL/CMOS control signals
Application
CD-RW applications
Writable optical drives
Laser diode current switching
Ordering Information
Part No
EL6277CU
Temp. Range
0°C to +70°C
Package
QSOP-16
Outline #
MDP0041
General Description
The EL6277C is a high-performance three channel laser diode current
driver that provides controlled current to a grounded laser diode.
Channel R and 2 can provide 100mA per channel of DC or pulsed cur-
rent, while channel 3 can provide 200mA per channel. Channels 2, and
3 must be used as the write channels, with switching speeds of approx-
imately three nanosecond rise/fall time. All three channels are
summed together at the IOUT output, allowing the user to create multi-
level waveforms in order to optimize laser diode performance. The
level of the output current is set by an analog voltage applied to an
external resistor which converts the voltage into a current at the IIN pin
(near ground). The current seen at this pin is then amplified by 100X
to become a current source at pin IOUT.
An on-chip 500 MHz oscillator is provided to allow current modula-
tion when in the read mode. This is turned on when the OSCEN pin is
held high (floating not recommended). Complete control of amplitude
and frequency is set by two external resistors connected to ground at
pins RFREQ and RAMP (see graphs in this data sheet for further
explanation). The oscillator will also turn off whenever either of the
OUTEN pins for channels 2 or 3(the write channels) are low (see truth
table).
Output current pulses are enabled when a ‘Low’ signal is applied to
the OUTEN pin. No output current flows when OUTEN is ‘H’, and
additional laser diode protection is provided since the OUTEN input
will float high when open. Complete IOUT shut-off is also achieved by
holding the ENABLE pin low, which will override the OUTEN con-
trol pins.
The external resistors allow the user to accurately and independently
set each amplifier trans conductance by applying a voltage to each
resistor, without restriction on the voltage range. Alternatively, the IIN
pin can be biased from a current DAC or other current source.
Connection Diagram
IINR
IIN2
GND
RFREQ
IIN3
OUTENR
OUTEN2
OUTEN3
1
2
3
4
5
6
7
8
16 VCC
15 VCC
14 IOUT
13 GND
12 RAMP
11 ENABLE
10 OSCEN
9 VCC
© 1997 Elantec, Inc.






구       성총 2 페이지
다운로드[ EL6277CU.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

상호 : 아이지 인터내셔날

사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
EL6277C

3-Channel Laser Diode Driver Oscillator

Elantec Semiconductor
Elantec Semiconductor
EL6277CU

3-Channel Laser Diode Driver Oscillator

Elantec Semiconductor
Elantec Semiconductor

DataSheet.kr    |   2020   |  연락처   |  링크모음   |   검색  |   사이트맵