|
|
Número de pieza | DTA115EE | |
Descripción | PNP Digital Transistor | |
Fabricantes | ROHM Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de DTA115EE (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! DTA115E series
PNP -100mA -50V Digital Transistor (Bias Resistor Built-in Transistor)
Datasheet
Parameter
VCC
IC(MAX.)
R1
R2
Value
-50V
-100mA
100kΩ
100kΩ
lFeatures
1) Built-In Biasing Resistors, R1 = R2 = 100kΩ
2) Built-in bias resistors enable the configuration of
an inverter circuit without connecting external
input resistors (see inner circuit) .
3) Only the on/off conditions need to be set
for operation, making the circuit design easy.
4) Complementary NPN Types: DTC115E series
lApplication
INVERTER, INTERFACE, DRIVER
lInner circuit
DTA115EM/ DTA115EEB/ DTA115EUB
lOutline
SOT-723
DTA115EM
(VMT3)
SOT-723
DTA115EE
(EMT3)
SOT-323
SOT-416FL
DTA115EEB
(EMT3F)
SOT-323FL
DTA115EUB
(UMT3F)
SOT-346
DTA115EUA
(UMT3)
DTA115EKA
(SMT3)
DTA115EE/ DTA115EUA/ DTA115EKA
lPackaging specifications
Part No.
Package
Package
size
Taping
code
Reel size Tape width
(mm) (mm)
Basic
ordering
unit.(pcs)
Marking
DTA115EM SOT-723
1212
T2L
180
8
8000
19
DTA115EEB SOT-416FL 1616
TL
180
8
3000
19
DTA115EE SOT-723
1616
TL
180
8
3000
19
DTA115EUB SOT-323FL 2021
TL
180
8
3000
19
DTA115EUA SOT-323
2021 T106
180
8
3000
19
DTA115EKA SOT-346
2928 T146
180
8
3000
19
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
1/10
20160303 - Rev.002
1 page DTA115E series
lDimensions
Datasheet
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
5/10
20160303 - Rev.002
5 Page Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASSⅢ
CLASSⅣ
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet DTA115EE.PDF ] |
Número de pieza | Descripción | Fabricantes |
DTA115E | PNP DIGITAL TRANSISTOR | Unisonic Technologies |
DTA115EE | Digital Transistors | ON Semiconductor |
DTA115EE | PNP Digital Transistor | ROHM Semiconductor |
DTA115EE | Bias Resistor Transistor PNP Silicon | WEITRON |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |