|
|
PDF TZA3034T Data sheet ( Hoja de datos )
| Número de pieza | TZA3034T | |
| Descripción | SDH/SONET STM1/OC3 postamplifiers | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TZA3034T (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TZA3034T; TZA3034U
SDH/SONET STM1/OC3
postamplifiers
Objective specification
File under Integrated Circuits, IC19
1998 Jul 07
1 page  
Philips Semiconductors
SDH/SONET STM1/OC3 postamplifiers
Objective specification
TZA3034T; TZA3034U
Bonding pad locations
handbook, full pagewidth
AGND
n.c.
AGND
1.58(1) DIN
mm
DINQ
AGND
TEST
VCCA
32
4
1 32 31 30 29 28
27
5
6
7x
8
0
0
9y
10 TZA3034U
26
25
24
23
22
21
11 20
12 13 14 15 16 17 18 19
VCCD
TEST
DGND
DOUT
DOUTQ
DGND
TEST
DGND
(1) Typical value.
Pad size: 90 × 90 µm.
1.58 mm(1)
MGR283
Fig.3 Bonding pad locations: TZA3034U.
FUNCTIONAL DESCRIPTION
The TZA3034 accepts up to 155 Mbits/s SD/SONET data
streams, with amplitudes from 2 mV (p-p) up to 1 V (p-p)
single-ended. The input signal will be amplified and limited
to differential PECL output levels (see Fig.1).
The input buffer A1 presents an impedance of
approximately 4.5 kΩ to the data stream on the inputs DIN
and DINQ. The input can be used both single-ended and
differential, but differential operation is preferred for better
performance.
Because of the high gain of the postamplifier, a very small
offset voltage would shift the decision level in such a way
that the input sensitivity decreases drastically. Therefore a
DC offset compensation circuit is implemented in the
TZA3034, which keeps the input of buffer A3 at its toggle
point in the absence of any input signal.
An input signal level detection is implemented to check if
the input signal is above the user-programmed level.
The outcome of this test is available at the PECL
outputs ST and STQ. This flag can also be used to prevent
the PECL outputs DOUT and DOUTQ from reacting to
noise in the absence of a valid input signal, by connecting
the output STQ to the input JAM. This insures that data will
only be transmitted when the input signal-to-noise ratio is
sufficient for low bit error rate system operation.
PECL logic
The logic level symbol definitions for PECL are shown in
Fig.4.
Input biasing
The input pins DIN and DINQ are DC biased at
approximately 2.55 V by an internal reference generator
(see Fig.5). The TZA3034 can be DC coupled, but AC
coupling is preferred. In case of DC coupling, the driving
source must operate within the allowable input signal
range (2.0 V to VCCA + 0.5 V). Also a DC offset voltage of
1998 Jul 07
5
5 Page 
Philips Semiconductors
SDH/SONET STM1/OC3 postamplifiers
Objective specification
TZA3034T; TZA3034U
CHARACTERISTICS
For typical values Tamb = 25 °C and VCC = 3.3 V; minimum and maximum values are valid over the entire ambient
temperature range and supply voltage range; all voltages with respect to ground; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX. UNIT
Supply
VCC
ICCD
ICCA
Ptot
Tj
Tamb
supply voltage
digital supply current
analog supply current
total power dissipation
junction temperature
ambient temperature
note 1
note 1
Inputs: DIN and DINQ
Vi(se)(p-p)
input signal voltage
single-ended (peak-to-peak)
Vi(dif)(p-p)
input signal voltage
differential (peak-to-peak)
VI
VIO(eq)
absolute input signal voltage
equivalent input signal offset
voltage
VIO(cor)
input offset voltage correction note 2
range
Ri
Ci
Vn(i)(rms)
input resistance
input capacitance
equivalent input RMS noise
voltage
single-ended
single-ended
note 3
3
−
−
−
−40
−40
0.002
0.004
2.1
−
−5
2.9
−
−
3.3
18
15
110
−
+25
−
−
2.55
−
−
4.5
−
45
5.5
27
22
270
+120
+85
V
mA
mA
mW
°C
°C
1.0 V
2.0 V
VCCA + 0.5 V
50 µV
+5 mV
7.6 kΩ
2.5 pF
60 µV
Input signal level-detect: RSET
Iref
Vref
Vth(p-p)
reference current
reference voltage
programmability
(single-ended, peak-to-peak)
note 4
referred to VCCA
Vi = 200 kHz square
wave
hys hysteresis
electrically measured
RF filter resistance
tF filter time constant
CF = 0
PECL outputs: DOUT and DOUTQ
VOL
VOH
tr
tf
tw(p-p)
f-3dB(l)
f-3dB(h)
LOW-level output voltage
HIGH-level output voltage
rise time
fall time
pulse width distortion
low frequency −3 dB point
high frequency −3 dB point
RL = 50 Ω to VCC − 2 V
RL = 50 Ω to VCC − 2 V
20% to 80%
80% to 20%
5
−1.55
2
2
14
0.5
−
−1.5
−
3
25
1.0
VCC − 1840 −
VCC − 1100 −
− 1.5
− 1.5
−−
− 0.85
110 150
60
−1.45
12
4
41
2.0
µA
V
mV
dB
kΩ
µs
VCC − 1620
VCC − 900
2.2
mV
mV
ns
2.2 ns
0.1 ns
1.5 kHz
190 MHz
1998 Jul 07
11
11 Page | ||
| Páginas | Total 18 Páginas | |
| PDF Descargar | [ Datasheet TZA3034T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TZA3034 | SDH/SONET STM1/OC3 postamplifier | NXP Semiconductors |
| TZA3034 | SDH/SONET STM1/OC3 and STM4/OC12 transceiver | NXP Semiconductors |
| TZA3034T | SDH/SONET STM1/OC3 postamplifiers | NXP Semiconductors |
| TZA3034T | SDH/SONET STM1/OC3 postamplifier | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |