Datasheet.kr   

U2008B-MFPG3 데이터시트 PDF




ATMEL Corporation에서 제조한 전자 부품 U2008B-MFPG3은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 U2008B-MFPG3 자료 제공

부품번호 U2008B-MFPG3 기능
기능 Low-Cost Phase-Control IC with Soft Start
제조업체 ATMEL Corporation
로고 ATMEL Corporation 로고


U2008B-MFPG3 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 10 페이지수

미리보기를 사용할 수 없습니다

U2008B-MFPG3 데이터시트, 핀배열, 회로
Low-Cost Phase-Control IC with Soft Start
U2008B
Description
The U2008B is designed as a phase-control circuit in
bipolar technology. It enables load-current detection as
well as mains-compensated phase control. Motor control
with load-current feedback and overload protection are
preferred applications.
Features
D Full wave current sensing
D Mains supply variation compensated
D Variable soft-start or load-current sensing
D Voltage and current synchronization
D Automatic retriggering switchable
D Triggering pulse typ. 125 mA
D Internal supply-voltage monitoring
D Current requirement v 3 mA
Applications
D Low-cost motor control
D Domestic appliance
Block Diagram
230 V ~
Load
Limiting
detector
22 kW/2W BYT51K
R2
330 kW
R1 D1
amax
R8
1 MW
76
Voltage
detector
Mains voltage
compensation
Automatic
retriggering
TIC
226
R3
180W
8
1
Current
detector
Full wave load
current detector
Soft start
R6
^
V(R6)
=
±250
mV
Phase
control unit
ö = f (V3)
U2008B
23
C3
3.3 nF
C4
100 nF
+–
Supply
voltage
limiting
Reference
voltage
Voltage
monitoring
R10 100 kW
Load current
compensation
5 –VS
C1
22 mF/
25 V
4 GND
R14
47 kW
Set point
R7
P1
Figure 1. Block diagram with typical circuit: Load current sensing
Rev. A4, 12-Jan-01
1 (10)




U2008B-MFPG3 pdf, 반도체, 판매, 대치품
U2008B
Current Synchronization, Pin 8
Mains
Current synchronization fulfils two functions:
* Monitoring the current flow after triggering.
In case the triac extinguishes again or it does not switch
on, automatic triggering is activated as long as
triggering is successful.
* Avoiding triggering due to inductive load.
In the case of inductive load operation, the current
synchronization ensures that in the new half wave no
pulse is enabled as long as there is a current available
from the previous half wave, which flows from the
opposite polarity to the actual supply voltage.
R2
2x
BZX55
C6V2
7
U2008B
4
A special feature of the IC is the realization of current
synchronization. The device evaluates the voltage at the
pulse output between the gate and reference electrode of
the triac. This results in saving separate current
synchronization input with specified series resistance.
Voltage Synchronization with Mains Voltage
Compensation, Pin 7
The voltage detector synchronizes the reference ramp
with the mains supply voltage. At the same time, the
mains-dependent input current at Pin 7 is shaped and rec-
tified internally. This current activates the automatic
retriggering and at the same time is available at Pin 3 (see
figure 9). By suitable dimensioning, it is possible to attain
the specified compensation effect. Automatic
retriggering and mains voltage compensation are not
activated until |V7 4| increases to 8 V. The resistance
Rsync. defines the width of the zero voltage cross-over
pulse, synchronization current, and hence the mains sup-
ply voltage compensation current. If the mains voltage
compensation and the automatic retriggering are not
required, both functions can be suppressed by limiting
|V7 – 4| v 7 V (see figure 4).
Figure 4. Suppression of automatic retriggering and mains
voltage compensation
A further feature of the IC is the selection between soft-
start or load-current compensation. Soft start is possible
by connecting a capacitor between Pin 1 and Pin 4, see
figure 8. In the case of load-current compensation, Pin 1
is directly connected with resistance R6, which is used for
sensing load current.
Load Current Detection, Pin 1
The circuit continuously measures the load current as a
voltage drop at resistance R6. The evaluation and use of
both half waves results in a quick reaction to load-current
change. Due to voltage at resistance R6, there is an
increase of input current at Pin 1. This current increase
controls the internal current source, whose positive
current values is available at Pin 3 (see figure 11). The
output current generated at Pin 3 contains the difference
from the load-current detection and from the
mains-voltage compensation (see figure 9).
The effective control voltage is the final current at Pin 3
together with the desired value network. An increase of
mains voltage causes the increase of control angle α. An
increase of load current results in a decrease in the control
angle. This avoids a decrease in revolution by increasing
the load as well as the increase of revolution by the
increment of mains supply voltage.
4 (10)
Rev. A4, 12-Jan-01

4페이지










U2008B-MFPG3 전자부품, 판매, 대치품
250
200 33 nF
6.8 nF
10 nF 4.7 nF 3.3 nF
150
2.2 nF
100 Cö/ t = 1.5 nF
50
0
0
120
100
80
60
40
20
0
0
200 400 600 800 1000
Rö (R8) ( kW )
Figure 5. Ramp control
VGT=–1.2V
200 400 600 800 1000
RGT ( W )
Figure 6. Pulse output
400
Dtp/DCö=9ms/nF
300
200
100
0
0 10 20
Cö = ( nF )
Figure 7. Output-pulse width
30
Rev. A4, 12-Jan-01
U2008B
1
0
–1
–2
–3
–4
–5
0
C5=1mF
10mF
4.7mF
Supply
R1=22kW/2W
C1=100mF/25V
1 2 3 45
t(s)
Figure 8. Option soft start
0
40
80
120
160 Pins 1
Vs=–13V
200
–2
–1
Reference Point
Pin 10
01
I7 ( mA )
2
Figure 9. Mains voltage compensation
100
Max. Series Resistance
VM=230V
80
60
40
20
0
02
46
IS ( mA )
8 10
Figure 10. Maximum resistance of R1
7 (10)

7페이지


구       성 총 10 페이지수
다운로드[ U2008B-MFPG3.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
U2008B-MFPG3

Low-Cost Phase-Control IC with Soft Start

ATMEL Corporation
ATMEL Corporation

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵