Datasheet.kr   

TODX270 데이터시트 PDF




Toshiba Semiconductor에서 제조한 전자 부품 TODX270은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 TODX270 자료 제공

부품번호 TODX270 기능
기능 FIBER OPTIC TRANSCEIVING MODULE
제조업체 Toshiba Semiconductor
로고 Toshiba Semiconductor 로고


TODX270 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 9 페이지수

미리보기를 사용할 수 없습니다

TODX270 데이터시트, 핀배열, 회로
FIBER OPTIC TRANSCEIVING MODULE
TODX270
FIBER OPTIC TRANSCEIVING
MODULE FOR DUPLEX DIGITAL
SIGNAL COMMUNICATION
l Data rate: DC to 6 Mb / s (NRZ code)
l Transmission distance: Up to 1000 m
l TTL interface
l LED is driven by Differential circuit.
l ATC (Automatic Threshold Control) circuit is
used for stabilized output at wide range of
optical power level.
TODX270
Unit: mm
1. Maximum Ratings (Ta = 25°C)
Characteristics
Symbol
Rating
Storage Temperature
Operating Temperature
Supply Voltage
Input Voltage
Low Level Output Current
High Level Output Current
Soldering Temperature
Tstg
Topr
VCC
VIN
IOL
IOH
Tsol
40 to 70
40 to 70
0.5 to 7
0.5 to VCC + 0.5
20
1
260 (Note 1)
Note 1: Soldering time 3 s (More than 1 mm apart from the package).
Unit
°C
°C
V
V
mA
mA
°C
Handling precaution: The LEDs used in this product contain GaAs (Gallium Arsenide).
Care must be taken to protect the safety of people and the environment when scrapping or
terminal processing.
1 2001-07-26




TODX270 pdf, 반도체, 판매, 대치품
TODX270
Note 8: There give characteristic examples, and its values are not guaranteed.
4
2001-07-26

4페이지










TODX270 전자부품, 판매, 대치품
TODX270
7. Precaution on Use
(1) Maximum rating
The maximum ratings are the limit values which must not be exceeded during operation of device.
None of these rating value must not be exceeded. If the maximum rating value is exceeded, the
characteristics of devices may never be restored properly. In extreme cases, the device may be
permanently damages.
(2) Lifetime of light emitters
If an optical module is used for a long period of time, degeneration in the characteristics will mostly
be due to a lowering of the fiber output power (Pf). This is caused by the degradation of the optical
output of the LEDs used as the light source. The cause of degradation of the optical output of the
LEDs may be defects in wafer crystallization or mold resin stress. The detailed causes are, however,
not clear.
The lifetime of light emitters is greatly influenced by the operating conditions and the environment in
which it is used as well as by the lifetime characteristics unique to the device type. Thus, when a light
emitting device and its operating conditions determined, Toshiba recommend that lifetime
characteristics be checked.
Depending on the environment conditions, Toshiba recommend that maintenance such as regular
checks of the amount of optical output in accordance with the condition of operating environment.
(3) Soldering
Optical modules are comprised of internal semiconductor devices. However, in principle, optical
modules are optical components. During soldering, ensure that flux does not contact with the emitting
surface or the detecting surface. Also ensure that proper flux removal is conducted after soldering.
Some optical modules come with a protective cap. The protective cap is used to avoid malfunction
when the optical module is not in use. Note that it is not dust or waterproof.
As mentioned before, optical modules are optical components. Thus, in principle, soldering where
there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend
that soldering be performed without the optical module mounted on the board. Then, after the board
has been cleaned, the optical module should be soldered on to the board manually.
If the optical module cannot be soldered manually, use nonhalogen (chlorinefree) flux and make
sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the
effects of flux. In such a cases, be sure to check the devices’ reliability.
(4) Noise resistance
It is believed that the use of optical transfer devices improve noise resistance. In theory, optical fiber
is not affected by noise at all. However, receiving modules which handle signals whose level is
extremely small, are susceptible to noise.
TOSLINK improve noise resistance to use a conductive case. However, the current signal output by
the optical receiving modules’ photodiode is extremely small. Thus, in some environments, shielding
the case may not achieve sufficient noise resistance.
First systems which incorporate TOSLINK, Toshiba recommend testing using the actual device to
check its noise resistance.
Use a simple noise filter on TOSLINK fiber optic transceiving module’s power line. If the ripple in the
power supply used is significant, reinforce the filter.
The optical module is to be used in an area which is susceptible to radiated noise, increase the
shielding by covering the optical module and the power line filter with a metallic cover.
(5) Vibration and shock
This module is plastic sealed and has its wire fixed by resin. This structure is relatively resistant to
vibration and shock. In actual equipment, there are sometime cases in which vibration, shock, or
stress is applied to soldered parts or connected parts, resulting in lines cut. A care must be taken in
the design of equipment which will be subject to high levels of vibration.
(6) Fixing Fiber Optical Transceiving Module
Solder the fixed pin (pins 9 and 10) of fiber optic transceiving module TODX270 to the printed circuit
board to fix the module to the board.
(7) Shielding and Wiring Pattern of Fiber Optic Transceiving Modules
To shield, connect the fixed pins (pins 9 and 10) of fiber optic transceiving module TODX270 to the
GND.
Where the fiber optic transceiving module uses conductive resin, be careful that the case does not
touch wiring (including land).
To improve noise resistance, shield the optical module and the power line filter using a metallic cover.
7 2001-07-26

7페이지


구       성 총 9 페이지수
다운로드[ TODX270.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
TODX270

FIBER OPTIC TRANSCEIVING MODULE

Toshiba Semiconductor
Toshiba Semiconductor
TODX270

FIBER OPTIC TRANSCEIVING MODULE

Toshiba Semiconductor
Toshiba Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵