|
|
|
부품번호 | TDA8560Q 기능 |
|
|
기능 | 2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facility | ||
제조업체 | NXP Semiconductors | ||
로고 | |||
전체 16 페이지수
INTEGRATED CIRCUITS
DATA SHEET
TDA8560Q
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic
facility
Product specification
Supersedes data of March 1994
File under Integrated Circuits, IC01
1996 Jan 08
Philips Semiconductors
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility
Product specification
TDA8560Q
PINNING
SYMBOL
IN 1
GND(S)
VP1
OUT 1A
GND1
OUT 1B
OUT 2A
GND2
OUT 2B
VP2
MODE
VDIAG
IN 2
PIN DESCRIPTION
1 input 1
2 signal ground
3 supply voltage 1
4 output 1A
5 power ground 1
6 output 1B
7 output 2A
8 power ground 2
9 output 2B
10 supply voltage 2
11 mode switch input
12 diagnostic output
13 input 2
IN 1 1
GND(S) 2
V P1 3
OUT 1A 4
GND1 5
OUT 1B 6
OUT 2A 7 TDA8560Q
GND2 8
OUT 2B 9
VP2 10
MODE 11
V DIAG 12
IN 2 13
MEA855 - 1
FUNCTIONAL DESCRIPTION
The TDA8560Q contains two identical amplifiers and can
be used for bridge applications. The gain of each amplifier
is fixed at 40 dB. Special features of the device are as
follows.
Mode select switch (pin 11)
• Standby: low supply current (<100 µA)
• Mute: input signal suppressed
• Operating: normal on condition.
Since this pin has a very low input current (<40 µA), a low
cost supply switch can be applied.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during ≥100 ms (charging of the input
capacitors at pin 1 and pin 13).
This can be achieved by:
• Microprocessor control
• External timing circuit (see Fig.7).
Diagnostic output (pin 12)
DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 12
goes low. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 12 is independent of the number of channels that are
clipping (see Fig.3).
handbook, halfpageVO
0
V12
VP
0
MGA721
t
Fig.2 Pin configuration.
1996 Jan 08
Fig.3 Distortion detector waveform.
4
4페이지 Philips Semiconductors
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility
Product specification
TDA8560Q
DC CHARACTERISTICS
VP = 14.4 V; Tamb = 25 °C; measured in Fig.6; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Supply
VP supply voltage
Iq quiescent current
Operating condition
V11
I11
VO
∆VO
mode switch voltage level
mode switch current
DC output voltage
DC output offset voltage
Mute condition
V11
VO
∆VO
mode switch voltage level
DC output voltage
DC output offset voltage
Standby condition
V11 mode switch voltage level
Isb standby current
Diagnostic output
V12 diagnostic output voltage
note 1
RL = ∞
6.0 14.4 18 V
− 115 180 mA
V11 = 14.4 V
note 2
8.5 −
VP V
− 15 40 µA
− 7.0 − V
− − 200 mV
note 2
3.3 −
6.4 V
− 7.0 − V
− − 200 mV
0−2V
− 0.1 100 µA
any short-circuit or clipping − − 0.6 V
Notes
1. The circuit is DC adjusted at VP = 6 to 18 V and AC operating at VP = 8.5 to 18 V.
2. At 18 V < VP < 30 V the DC output voltage ≤1⁄2VP.
1996 Jan 08
7
7페이지 | |||
구 성 | 총 16 페이지수 | ||
다운로드 | [ TDA8560Q.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
TDA8560 | 2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facility | NXP Semiconductors |
TDA8560Q | 2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facility | NXP Semiconductors |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |