|
|
|
부품번호 | TEA1533T 기능 |
|
|
기능 | GreenChipTMII SMPS control IC | ||
제조업체 | NXP Semiconductors | ||
로고 | |||
전체 24 페이지수
INTEGRATED CIRCUITS
DATA SHEET
TEA1533T; TEA1533AT
GreenChipTMII SMPS control IC
Product specification
Supersedes data of 2002 May 31
2002 Aug 23
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
VCC 2
3
GND
S1
SUPPLY
MANAGEMENT
M-level
internal UVLO start
supply
VOLTAGE
CONTROLLED
OSCILLATOR
FREQUENCY
CONTROL
START-UP
CURRENT SOURCE
DEMAG
SHORT
PROTECTION
OCP
VALLEY
Iprot(DEM)
clamp
LOGIC
50
mV
100
mV
UP/DOWN
COUNTER
OVER-
VOLTAGE
PROTECTION
14
DRAIN
12, 13
7
HVS
n.c.
DEM
6
CTRL
Iprot(CTRL)
−1
POWER-ON
RESET
2.5 V
burst
detect
OVER-
TEMPERATURE
PROTECTION
LOGIC
SQ
UVLO R Q
SQ
VCC < 4.5 V
or UVLO
(TEA1533AT)
RQ
DRIVER
LEB
blank
OCP
11 DRIVER
soft
start
S2
Iss
0.5 V
9 Isense
TEA1533T
TEA1533AT
MAXIMUM
ON-TIME
PROTECTION
short
winding
0.88 V
OVERPOWER
PROTECTION
MGU500
Fig.2 Block diagram.
4페이지 Philips Semiconductors
GreenChipTMII SMPS control IC
Product specification
TEA1533T; TEA1533AT
handbook, full pagewidth
CTRL
1.5 V − VCTRL current
comparator
DRIVER
X2
DRIVER
Isense
Vx
150 mV
V
I
OSCILLATOR
fosc
fmax
fmin
cycle
skipping
dV2
1
0
dV1 Vx (mV)
150
Vx (mV)
MGU510
The voltage levels dV1 and dV2 are fixed in the IC to 50 mV (typical) and 18 mV (typical) respectively.
Fig.7 The cycle skipping circuitry.
Demagnetization
The system will be in discontinuous conduction mode all
the time. The oscillator will not start a new primary stroke
until the secondary stroke has ended.
Demagnetization features a cycle-by-cycle output
short-circuit protection by immediately lowering the
frequency (longer off-time), thereby reducing the power
level.
Demagnetization recognition is suppressed during the first
tsuppr time. This suppression may be necessary in
applications where the transformer has a large leakage
inductance, at low output voltages and at start-up.
If pin DEM is open-circuit or not connected, a fault
condition is assumed and the converter will stop operating
immediately. Operation will recommence as soon as the
fault condition is removed.
If pin DEM is shorted to ground, again a fault condition is
assumed and the converter will stop operating after the
first stroke. The converter will subsequently enter the safe
restart mode. This situation will persist until the
short-circuit is removed.
Minimum and maximum ‘on-time’
The minimum ‘on-time’ of the SMPS is determined by the
Leading Edge Blanking (LEB) time. The IC limits the
‘on-time’ to 50 µs. When the system desires an ‘on-time’
longer than 50 µs, a fault condition is assumed (e.g.
removed Ci in Fig.11), the IC will stop switching and enter
the safe restart mode.
2002 Aug 23
7
7페이지 | |||
구 성 | 총 24 페이지수 | ||
다운로드 | [ TEA1533T.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
TEA1533AP | GreenChip SMPS control IC | NXP Semiconductors |
TEA1533AT | GreenChipTMII SMPS control IC | NXP Semiconductors |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |