Datasheet.kr   

P89CE558EFB 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 P89CE558EFB은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 P89CE558EFB 자료 제공

부품번호 P89CE558EFB 기능
기능 Single-chip 8-bit microcontroller
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


P89CE558EFB 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 70 페이지수

미리보기를 사용할 수 없습니다

P89CE558EFB 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
P83CE558/P80CE558/P89CE558
Single-chip 8-bit microcontroller
Preliminary specification
IC20 Data Handbook
1996 Aug 06
Philips
Semiconductors




P89CE558EFB pdf, 반도체, 판매, 대치품
Philips Semiconductors
Single-chip 8-bit microcontroller
Preliminary specification
P83CE558/P80CE558/P89CE558
VSS
VDD
XTAL1
XTAL2
EA
ALE/WE *
PSEN
AVSS
AVDD
AVref+
AVref–
ADEXS
PWM0
PWM1
SCL
SDA
ADC0-7
0
1
2
3
4
5
6
7
CMSR0-5
CMT0
0
1
2
3
4
5
6
7
CMT1
RSTIN
RSTOUT
EW
XTAL3
XTAL4
SELXTAL1
00
11
22
33
44
55
66
77
LOW ORDER ADDRESS
AND DATA BUS AD0–7
0 CT0I/INT2
1 CT1I/INT3
2 CT2I/INT4
3
4 CT3I/INT5
5 T2
6 RT2
7
0
1
2
3 HIGH ORDER ADDRESS BUS
4 A8–15
5
6
7
0 RXD/DATA
1 TXD/CLOCK
2 INT0
3 INT1
4 T0
5
6 T1
7 WR
RD
*) only P89CE558 with alternate function WE
Figure 2. Functional diagram
1996 Aug 06
4

4페이지










P89CE558EFB 전자부품, 판매, 대치품
Philips Semiconductors
Single-chip 8-bit microcontroller
Preliminary specification
P83CE558/P80CE558/P89CE558
PIN DESCRIPTION (Continued)
SYMBOL
P3.0 – P3.7
N.C.
XTAL2
XTAL1
P2.0 – P2.7
PSEN
ALE/WE
EA
P0.7–P0.0
XTAL3
XTAL4
SELXTAL1
PIN
41 – 48
49 – 50
51
52
55 – 62
63
64
65
68 –75
78
79
80
DESCRIPTION
8-bit quasi-bidirectional I/O port
Port pin
Alternative function
P3.0
RXD :
Serial input port
P3.1
TXD :
Serial output port
P3.2
INT0 :
External interrupt
P3.3
INT1 :
External interrupt
P3.4
T0 :
Timer 0 external input
P3.5
T1 :
Timer 1 external input
P3.6
WR :
External data memory write strobe
P3.7
RD :
External data memory read strobe
Not connected pins.
Crystal pin 2: output of the inverting amplifier that forms the oscillator. Left open-circuit when an external
oscillator clock is used.
Crystal pin 1: input to the inverting amplifier that forms the oscillator, and input to the internal clock
generator. Receives the external oscillator clock signal when an external oscillator is used. Must be
connected to logic HIGH if the PLL oscillator is selected (SELXTAL1 = LOW).
Port2: 8-bit quasi-bidirectional I/O port with internal pull-ups.During access to external memories
(RAM/ROM) that use 16-bit addresses (MOVX@DPTR) Port 2 emits the high order address byte. The
alternative function of P2.7 for the P89CE558 is the output enable signal for verify/read modes (active low).
Port 2 can sink/source one TTL (=4 LSTTL) input. It can drive CMOS inputs without external pull-ups.
Program Store Enable output: read strobe to the external program memory via Port 0 and 2. Is activated
twice each machine cycle during fetches from external program memory. When executing out of external
program memory two activations of PSEN are skipped during each access to external data memory. PSEN
is not activated (remains HIGH) during no fetches from external program memory. PSEN can sink/source 8
LSTTL inputs. It can drive CMOS inputs without external pull-ups.
Address Latch Enable output: latches the low byte of the address during access of external memory in
normal operation. It is activated every six oscillator periods except during an external data memory access.
ALE/WE can sink/-source 8 LSTTL inputs. It can drive CMOS inputs without an external pull-up. The
alternative function for the P89CE558 is the programming pulse input WE.
To prohibit the toggling of ALE pin (RFI noise reduction) the bit RFI in the PCON Register (PCON.5) must be
set by software. This bit is cleared on RESET and can be set and cleared by software. When set, ALE pin
will be pulled down internally, switching an external address latch to a quiet state. The MOVX instruction will
still toggle ALE if external memory is accessed.
ALE will retain its normal high value during Idle Mode and a low value during Power-down Mode while in the
“RFI” mode. Additionally during internal access (EA = 1) ALE will toggle normally when the address exceeds
the internal program memory size. During external access (EA = 0) ALE will always toggle normally, whether
the flag “RFI” is set or not.
External Access Input: If, during RESET, EA is held at a TTL level HIGH the CPU executes out of the
internal program memory, provided the program counter is less than 32768. If, during RESET, EA is held at a
TTL level LOW the CPU executes out of external program memory via Port 0 and Port 2. EA is not allowed
to float. EA is latched during RESET and don’t care after RESET.
Port 0: 8-bit open drain bidirectional I/O port. It is also the multiplexed low-order address and data bus during
accesses to external memory (during theses accesses internal pull-ups are activated). Port 0 can sink/source
8 LSTTL inputs.
Crystal pin, output of the inverting amplifier that forms the 32 kHz oscillator
Crystal pin, input to the inverting amplifier that forms the 32 kHz oscillator. XTAL3 and XTAL4 are pulled
LOW if the PLL oscillator is not selected (SELXTAL1 = HIGH) or if Reset is active.
Must be connected to logic HIGH level to select the HF oscillator, using the XTAL1/XTAL2 crystal. If pulled low
the PLL is selected for clocking of the controller, using the XTAL3/ XTAL4 crystal.
NOTE:
1. To avoid a ‘latch-up’ effect at Power-on, the voltage at any pin at any time must not be higher or lower than VDD+ 0.5 V or VSS– 0.5 V
respectively.
1996 Aug 06
7

7페이지


구       성 총 70 페이지수
다운로드[ P89CE558EFB.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
P89CE558EFB

Single-chip 8-bit microcontroller

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵