|
|
PDF RX5000 Data sheet ( Hoja de datos )
| Número de pieza | RX5000 | |
| Descripción | 433.92 MHz Hybrid Receiver | |
| Fabricantes | RF Monolithics Inc | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RX5000 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
®
· Designed for Short-Range Wireless Control and Data Communications
· Supports RF Data Transmission Rates Up to 115.2 kbps
· 3 V, Low Current Operation plus Sleep Mode
· Stable, Easy to Use, Low External Parts Count
The RX5000 hybrid receiver is ideal for short-range wireless control and data applications where
robust operation, small size, low power consumption and low cost are required. The RX5000
employs RFM’s amplifier-sequenced hybrid (ASH) architecture to achieve this unique blend of
characteristics. All critical RF functions are contained in the hybrid, simplifying and speeding de-
sign-in. The RX5000 is sensitive and stable. A wide dynamic range log detector, in combination
with digital AGC and a compound data slicer, provide robust performance in the presence of
on-channel interference or noise. Two stages of SAW filtering provide excellent receiver out-
of-band rejection. The RX5000 generates virtually no RF emissions, facilitating compliance with
ETSI I-ETS 300 220 and similar regulations.
RX5000
433.92 MHz
Hybrid
Receiver
Absolute Maximum Ratings
Rating
Power Supply and All Input/Output Pins
Non-Operating Case Temperature
Soldering Temperature (10 seconds)
Value
-0.3 to +4.0
-50 to +100
250
Units
V
oC
oC
Electrical Characteristics (typical values given for 3.0 Vdc power supply, 25 oC)
Characteristic
Sym Notes
Operating Frequency
Modulation Type
fO
Data Rate
Receiver Performance, High Sensitivity Mode
Sensitivity, 2.4 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 2.4 kbps, 10-3 BER, Pulse Test Method
1
Current, 2.4 kbps (RPR = 330 K)
Sensitivity, 19.2 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 19.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 19.2 kbps (RPR = 330 K)
Sensitivity, 115.2 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 115.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 115.2 kbps
Receiver Performance, Low Current Mode
Sensitivity, 2.4 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 2.4 kbps, 10-3 BER, Pulse Test Method
1
Current, 2.4 kbps (RPR = 1100 K)
2
Minimum
433.72
Typical
OOK/ASK
-109
-103
3.0
-105
-99
3.1
-101
-95
3.8
-104
-98
1.8
Maximum
434.12
115.2
Units
MHz
kbps
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
1
1 page  
A n te n n a
R F IO
20
ESD
C hoke
SAW
C R F ilte r
R X 5 0 0 0 S e r ie s A S H R e c e iv e r B lo c k D ia g r a m
C N TR L1
C N TR L0
17 18
B ia s C o n tr o l
P ow er
D ow n
C o n tro l
Log
V C C 1 : P in 2
V C C 2 : P in 1 6
G N D 1 : P in 1
G N D 2 : P in 1 0
G N D 3 : P in 1 9
N C : P in 8
R R E F : P in 1 1
C M P IN : P in 6
R FA1
SAW
D e la y L in e
A G C S et
G a in S e le c t
R FA2
D e te c to r
L o w -P a s s
F ilte r
LP FA D J 9
R LPF
BB
P u ls e G e n e r a to r
& R F A m p B ia s
P R A TE 14
1 5 P W ID T H
R PR R PW
AG C
C o n tro l
AG CCAP 3
C AGC
A G C R eset
BBO UT
P eak R ef
56
C BBO
D e te c to r
PKDET 4
C PKD
DS2
d B B e lo w
P e a k T h ld
AND 7
R XD ATA
AG C DS1
R e f T h ld
T h r e s h o ld
C o n tro l
TH LD 1
13
R TH1
11 12
R TH2
R REF
TH LD 2
Figure 2
the start of the next RFA1 ON sequence should be set to sample
the narrowest RF data pulse at least 10 times. Otherwise, significant
edge jitter will be added to the detected data pulse.
RX5000 Series ASH Receiver Block Diagram
Figure 2 is the general block diagram of the RX5000 series ASH
receiver. Please refer to Figure 2 for the following discussions.
Antenna Port
The only external RF components needed for the receiver are the
antenna and its matching components. Antennas presenting an im-
pedance in the range of 35 to 72 ohms resistive can be satisfactorily
matched to the RFIO pin with a series matching coil and a shunt
matching/ESD protection coil. Other antenna impedances can be
matched using two or three components. For some impedances,
two inductors and a capacitor will be required. A DC path from RFIO
to ground is required for ESD protection.
Receiver Chain
The output of the SAW filter drives amplifier RFA1. This amplifier in-
cludes provisions for detecting the onset of saturation (AGC Set),
and for switching between 35 dB of gain and 5 dB of gain (Gain Se-
lect). AGC Set is an input to the AGC Control function, and Gain Se-
lect is the AGC Control function output. ON/OFF control to RFA1
(and RFA2) is generated by the Pulse Generator & RF Amp Bias
function. The output of RFA1 drives the SAW delay line, which has
a nominal delay of 0.5 µs.
The second amplifier, RFA2, provides 51 dB of gain below satura-
tion. The output of RFA2 drives a full-wave detector with 19 dB of
threshold gain. The onset of saturation in each section of RFA2 is
detected and summed to provide a logarithmic response. This is
added to the output of the full-wave detector to produce an overall
detector response that is square law for low signal levels, and tran-
sitions into a log response for high signal levels. This combination
provides excellent threshold sensitivity and more than 70 dB of
detector dynamic range. In combination with the 30 dB of AGC
range in RFA1, more than 100 dB of receiver dynamic range is
achieved.
The detector output drives a gyrator filter. The filter provides a
three-pole, 0.05 degree equiripple low-pass response with excellent
group delay flatness and minimal pulse ringing. The 3 dB bandwidth
of the filter can be set from 4.5 kHz to 1.8 MHz with an external re-
sistor.
The filter is followed by a base-band amplifier which boosts the de-
tected signal to the BBOUT pin. When the receiver RF amplifiers
are operating at a 50%-50% duty cycle, the BBOUT signal changes
about 10 mV/dB, with a peak-to-peak signal level of up to 685 mV.
For lower duty cycles, the mV/dB slope and peak-to-peak signal
level are proportionately less. The detected signal is riding on a
1.1 Vdc level that varies somewhat with supply voltage, tempera-
ture, etc. BBOUT is coupled to the CMPIN pin or to an external data
recovery process (DSP, etc.) by a series capacitor. The correct
value of the series capacitor depends on data rate, data run length,
and other factors as discussed in the ASH Transceiver Designer’s
Guide.
When an external data recovery process is used with AGC, BBOUT
must be coupled to the external data recovery process and CMPIN
by separate series coupling capacitors. The AGC reset function is
driven by the signal applied to CMPIN.
When the receiver is placed in the power-down (sleep) mode, the
output impedance of BBOUT becomes very high. This feature helps
preserve the charge on the coupling capacitor to minimize data
slicer stabilization time when the receiver switches out of the sleep
mode.
Data Slicers
The CMPIN pin drives two data slicers, which convert the analog
signal from BBOUT back into a digital stream. The best data slicer
choice depends on the system operating parameters. Data slicer
DS1 is a capacitively-coupled comparator with provisions for an ad-
justable threshold. DS1 provides the best performance at low
5
5 Page 
Pin Name
Description
CNTRL1 and CNTRL0 select the receiver modes. CNTRL1 and CNTRL0 both high place the unit in the receive
mode. CNTRL1 and CNTRL0 both low place the unit in the power-down (sleep) mode. CNTRL1 is a
17
CNTRL1
high-impedance input (CMOS compatible). An input voltage of 0 to 300 mV is interpreted as a logic low. An input
voltage of Vcc - 300 mV or greater is interpreted as a logic high. An input voltage greater than Vcc + 200 mV
should not be applied to this pin. A logic high requires a maximum source current of 40 µA. Sleep mode requires a
maximum sink current of 1 µA. This pin must be held at a logic level; it cannot be left unconnected.
CNTRL0 is used with CNTRL1 to control the receiver modes. CNTRL0 is a high-impedance input (CMOS compat-
ible). An input voltage of 0 to 300 mV is interpreted as a logic low. An input voltage of Vcc - 300 mV or greater is
18 CNTRL0 interpreted as a logic high. An input voltage greater than Vcc + 200 mV should not be applied to this pin. A logic
high requires a maximum source current of 40 µA. Sleep mode requires a maximum sink current of 1 µA. This pin
must be held at a logic level; it cannot be left unconnected.
19
GND3
GND3 is an IC ground pin. It should be connected to GND1 by a short, low inductance trace.
RFIO is the receiver RF input pin. This pin is connected directly to the SAW filter transducer. Antennas presenting
an impedance in the range of 35 to 72 ohms resistive can be satisfactorily matched to this pin with a series match-
20
RFIO
ing coil and a shunt matching/ESD protection coil. Other antenna impedances can be matched using two or three
components. For some impedances, two inductors and a capacitor will be required. A DC path from RFIO to
ground is required for ESD protection.
S M -2 0 L P C B P a d L a y o u t
.4 6 0 0
0 .0 0 0
D im e n s io n s in in c h e s
.3 8 2 5
.3 5 7 5
.3 1 7 5
.2 7 7 5
.2 3 7 5
.1 9 7 5
.1 5 7 5
.1 1 7 5
.1 0 2 5
.0 7 7 5
Note: Specifications subject to change without notice.
11
file: rx5000v.vp, 2003.07.17 rev
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet RX5000.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RX5000 | 433.92 MHz Hybrid Receiver | RF Monolithics Inc |
| RX5003 | 303.825 MHz Hybrid Receiver | RF Monolithics Inc |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |