|
|
PDF RX5500 Data sheet ( Hoja de datos )
| Número de pieza | RX5500 | |
| Descripción | 433.92 MHz Hybrid Receiver | |
| Fabricantes | RF Monolithics Inc | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RX5500 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
®
· Designed for Short-Range Wireless Control Applications
· 3 V, Low Current Operation plus Sleep Mode
· Characterized for Automotive Applications
· High EMI Rejection Capability
The RX5500 hybrid receiver is ideal for short-range wireless control applications where robust
operation, small size, low power consumption and low cost are required. The RX5500 employs
RFM’s amplifier-sequenced hybrid (ASH) architecture to achieve this unique blend of character-
istics. All critical RF functions are contained in the hybrid, simplifying and speeding design-in.
The RX5500 is sensitive and stable. A wide dynamic range log detector provides robust perfor-
mance in the presence of on-channel interference or noise. Two stages of SAW filtering provide
excellent receiver out-of-band rejection. The RX5500 generates virtually no RF emissions, facili-
tating compliance with ETSI I-ETS 300 220 and similar regulations.
RX5500
433.92 MHz
Hybrid
Receiver
Absolute Maximum Ratings
Rating
Power Supply and All Input/Output Pins
Non-Operating Case Temperature
Soldering Temperature (10 seconds)
Value
-0.3 to +4.0
-50 to +100
250
Units
V
oC
oC
Electrical Characteristics (typical values given for 3.0 Vdc power supply, 25 oC)
Characteristic
Sym Notes
Operating Frequency
Modulation Type
fO
Data Rate
Receiver Performance, High Sensitivity Mode
Sensitivity, 1.2 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 1.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 1.2 kbps (RPR = 330 K)
Sensitivity, 2.4 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 2.4 kbps, 10-3 BER, Pulse Test Method
1
Current, 2.4 kbps (RPR = 330 K)
Sensitivity, 19.2 kbps, 10-3 BER, AM Test Method
2
1
Sensitivity, 19.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 19.2 kbps
Receiver Performance, Low Current Mode
Sensitivity, 1.2 kbps, 10-3 BER, AM Test Method
1
Sensitivity, 1.2 kbps, 10-3 BER, Pulse Test Method
1
Current, 1.2 kbps (RPR = 2000 K)
2
Minimum
433.72
Typical
OOK/ASK
-110.5
-104.5
2.9
-109
-103
3.0
-105
-99
3.1
-104
-98
1.65
Maximum
434.12
19.2
Units
MHz
kbps
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
dBm
dBm
mA
1
1 page  
R X 5 5 0 0 S e r ie s A S H R e c e iv e r B lo c k D ia g r a m
A n te n n a
R F IO
20
ESD
C hoke
SAW
C R F ilte r
R FA1
C N TR L1
C N TR L0
17 18
B ia s C o n tr o l
3
R FA1
SAW
D e la y L in e
P ow er
D ow n
C o n tro l
Log
V C C 1 : P in 2
V C C 2 : P in 1 6
G N D 1 : P in 1
G N D 2 : P in 1 0
G N D 3 : P in 1 9
N C : P in 8
R R E F : P in 1 1
C M P IN : P in 6
N C : P in 4
N C : P in 1 2
R FA2
D e te c to r
L o w -P a s s
F ilte r
LP FA D J 9
R LPF
P u ls e G e n e r a to r
& R F A m p B ia s
P R A TE 14
1 5 P W ID T H
R PR R PW
BBO UT
BB 5
6
7
C BBO D S 1
R e f T h ld
T h r e s h o ld
C o n tro l
TH LD 1 13
11 R R E F
R TH1
R REF
R XD ATA
Figure 2
the start of the next RFA1 ON sequence should be set to sample
the narrowest RF data pulse at least 10 times. Otherwise, significant
edge jitter will be added to the detected data pulse.
RX5500 Series ASH Receiver Block Diagram
Figure 2 is the general block diagram of the RX5500 series ASH
receiver. Please refer to Figure 2 for the following discussions.
Antenna Port
The only external RF components needed for the receiver are the
antenna and its matching components. Antennas presenting an im-
pedance in the range of 35 to 72 ohms resistive can be satisfactorily
matched to the RFIO pin with a series matching coil and a shunt
matching/ESD protection coil. Other antenna impedances can be
matched using two or three components. For some impedances,
two inductors and a capacitor will be required. A DC path from RFIO
to ground is required for ESD protection.
Receiver Chain
The output of the SAW filter drives amplifier RFA1. The output of
RFA1 drives the SAW delay line, which has a nominal delay of 0.5
µs.
The second amplifier, RFA2, provides 51 dB of gain below satura-
tion. The output of RFA2 drives a full-wave detector with 19 dB of
threshold gain. The onset of saturation in each section of RFA2 is
detected and summed to provide a logarithmic response. This is
added to the output of the full-wave detector to produce an overall
detector response that is square law for low signal levels, and tran-
sitions into a log response for high signal levels. This combination
provides excellent threshold sensitivity and more than 70 dB of
The detector output drives a gyrator filter. The filter provides a
three-pole, 0.05 degree equiripple low-pass response with excellent
group delay flatness and minimal pulse ringing. The 3 dB bandwidth
of the filter can be set from 4.5 kHz to 1.8 MHz with an external re-
sistor.
The filter is followed by a base-band amplifier which boosts the de-
tected signal to the BBOUT pin. When the receiver RF amplifiers
are operating at a 50%-50% duty cycle, the BBOUT signal changes
about 10 mV/dB, with a peak-to-peak signal level of up to 685 mV.
For lower duty cycles, the mV/dB slope and peak-to-peak signal
level are proportionately less. The detected signal is riding on a
1.1 Vdc level that varies somewhat with supply voltage, tempera-
ture, etc. BBOUT is coupled to the CMPIN pin or to an external data
recovery process (DSP, etc.) by a series capacitor. The correct
value of the series capacitor depends on data rate, data run length,
and other factors as discussed in the ASH Transceiver Designer’s
Guide.
When the receiver is placed in the power-down (sleep) mode, the
output impedance of BBOUT becomes very high. This feature helps
preserve the charge on the coupling capacitor to minimize data
slicer stabilization time when the receiver switches out of the sleep
mode.
Data Slicers
The CMPIN pin drives data slicer DS1, which convert the analog
signal from BBOUT back into a digital stream. Data slicer DS1 is a
capacitively-coupled comparator with provisions for an adjustable
threshold. The threshold, or squelch, offsets the comparator’s slicing
level from 0 to 90 mV, and is set with a resistor between the RREF
and THLD1 pins. This threshold allows a trade-off between receiver
sensitivity and output noise density in the no-signal condition. For
best sensitivity, the threshold is set to 0. In this case, noise is output
continuously when no signal is present. This, in turn, requires the
circuit being driven by the RXDATA pin to be able to process noise
(and signals) continuously.
This can be a problem if RXDATA is driving a circuit that must
“sleep” when data is not present to conserve power, or when it its
necessary to minimize false interrupts to a multitasking processor.
In this case, noise can be greatly reduced by increasing the thresh-
old level, but at the expense of sensitivity. The best 3 dB bandwidth
5
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet RX5500.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RX5500 | 433.92 MHz Hybrid Receiver | RF Monolithics Inc |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |