Datasheet.kr   

PB58A 데이터시트 PDF




ETC에서 제조한 전자 부품 PB58A은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PB58A 자료 제공

부품번호 PB58A 기능
기능 POWER BOOSTER AMPLIFIERS
제조업체 ETC
로고 ETC 로고


PB58A 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 4 페이지수

미리보기를 사용할 수 없습니다

PB58A 데이터시트, 핀배열, 회로
MICROTECHNOLOGY
POWER BOOSTER AMPLIFIERS
PB58 • PB58A
HTTP://WWW.APEXMICROTECH.COM (800) 546-APEX (800) 546-2739
FEATURES
• WIDE SUPPLY RANGE — ±15V to ±150V
• HIGH OUTPUT CURRENT —
1.5A Continuous (PB58)
2.0A Continuous (PB58A)
• VOLTAGE AND CURRENT GAIN
• HIGH SLEW — 50V/µs Minimum (PB58)
75V/µs Minimum (PB58A)
• PROGRAMMABLE OUTPUT CURRENT LIMIT
• HIGH POWER BANDWIDTH — 320 kHz Minimum
• LOW QUIESCENT CURRENT — 12mA Typical
• EVALUATION KIT — See EK50
APPLICATIONS
• HIGH VOLTAGE INSTRUMENTATION
• Electrostatic TRANSDUCERS & DEFLECTION
• Programmable Power Supplies Up to 280V p-p
DESCRIPTION
The PB58 is a high voltage, high current amplifier designed
to provide voltage and current gain for a small signal, general
purpose op amp. Including the power booster within the feed-
back loop of the driver amplifier results in a composite amplifier
with the accuracy of the driver and the extended output voltage
range and current capability of the booster. The PB58 can also
be used without a driver in some applications, requiring only an
external current limit resistor to function properly.
The output stage utilizes complementary MOSFETs, provid-
ing symmetrical output impedance and eliminating second
breakdown limitations imposed by Bipolar Transistors. Internal
feedback and gainset resistors are provided for a pin-strapable
gain of 3. Additional gain can be achieved with a single external
resistor. Compensation is not required for most driver/gain
configurations, but can be accomplished with a single external
capacitor. Enormous flexibility is provided through the choice of
driver amplifier, current limit, supply voltage, voltage gain, and
compensation.
This hybrid circuit utilizes a beryllia (BeO) substrate, thick film
resistors, ceramic capacitors and semiconductor chips to maxi-
mize reliability, minimize size and give top performance.
Ultrasonically bonded aluminum wires provide reliable inter-
connections at all operating temperatures. The 8-pin TO-3
package is electrically isolated and hermetically sealed using
one-shot resistance welding. The use of compressible isolation
washers voids the warranty.
TYPICAL APPLICATION
CF
Figure 1. Inverting
composite amplifier.
VIN R I
RF
+15V
+Vs
OP
AMP
IN
COM PB58
–15V
–Vs
R CL
OUT
CC
RG
RL
EQUIVALENT SCHEMATIC
Q2
Q1
IN
4
GAIN 6.2K
7
50K
COM
5
COMP
8
Q4
3.1K
Q6
Q11
Q9 Q10
3
+Vs
Q3
Q5
Q7
OUT
1
2
CL
Q8
–Vs
6
EXTERNAL CONNECTIONS
+Vs
3
CL
2
IN 4
COM
5
TOP VIEW
R CL
OUT
1
COMP
8
CC
–Vs 6
7
GAIN
RG
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected]




PB58A pdf, 반도체, 판매, 대치품
PB58 • PB58A
OPERATING
CONSIDERATIONS
GENERAL
Please read the “General Operating Considerations” sec-
tion, which covers stability, supplies, heatsinking, mounting,
current limit, SOA interpretation, and specification interpreta-
tion. Additional information can be found in the application
notes. For information on the package outline, heatsinks, and
mounting hardware, consult the “Accessory and Package
Mechanical Data” section of the handbook.
CURRENT LIMIT
For proper operation, the current limit resistor (RCL) must be
connected as shown in the external connection diagram. The
minimum value is 0.33with a maximum practical value of
47. For optimum reliability the resistor value should be set as
high as possible. The value is calculated as follows: +IL= .65/
RCL + .010, -IL = .65/RCL.
SAFE OPERATING AREA (SOA)
3
2
1
.5
.4
.3
steady
stasteteTacdy=
steady
state Tc
125°C
=
t = 100ms
state Tc
85°C
=
25°C
.2
.1
10 20 30 40 50 100 200 300
SUPPLY TO OUTPUT DIFFERENTIAL VOLTAGE, Vs –Vo (V)
NOTE: The output stage is protected against transient flyback.
However, for protection against sustained, high energy flyback, exter-
nal fast-recovery diodes should be used.
COMPOSITE AMPLIFIER CONSIDERATIONS
Cascading two amplifiers within a feedback loop has many
advantages, but also requires careful consideration of several
amplifier and system parameters. The most important of these
are gain, stability, slew rate, and output swing of the driver.
Operating the booster amplifier in higher gains results in a
higher slew rate and lower output swing requirement for the
driver, but makes stability more difficult to achieve.
GAIN SET
RG = [ (Av-1) * 3.1K] – 6.2K
Av = RG + 6.2K +1
3.1K
The booster’s closed-loop gain is given by the equation
above. The composite amplifier’s closed loop gain is deter-
mined by the feedback network, that is: –Rf/Ri (inverting) or
1+Rf/Ri (non-inverting). The driver amplifier’s “effective gain”
is equal to the composite gain divided by the booster gain.
Example: Inverting configuration (figure 1) with
R i = 2K, R f = 60K, R g = 0 :
Av (booster) = (6.2K/3.1K) + 1 = 3
Av (composite) = 60K/2K = – 30
Av (driver) = – 30/3 = –10
STABILITY
Stability can be maximized by observing the following guide-
lines:
1. Operate the booster in the lowest practical gain.
2. Operate the driver amplifier in the highest practical effec-
tive gain.
3. Keep gain-bandwidth product of the driver lower than the
closed loop bandwidth of the booster.
4. Minimize phase shift within the loop.
A good compromise for (1) and (2) is to set booster gain from
3 to 10 with total (composite) gain at least a factor of 3 times
booster gain. Guideline (3) implies compensating the driver as
required in low composite gain configurations. Phase shift
within the loop (4) is minimized through use of booster and loop
compensation capacitors Cc and Cf when required. Typical
values are 5pF to 33pF.
Stability is the most difficult to achieve in a configuration
where driver effective gain is unity (ie; total gain = booster
gain). For this situation, Table 1 gives compensation values for
optimum square wave response with the op amp drivers listed.
DRIVER
OP07
741
LF155
LF156
TL070
CCH
-
-
-
-
22p
CF CC FPBW SR
22p 22p 4kHz 1.5
18p 10p 20kHz 7
4.7p 10p 60kHz >60
4.7p 10p 80kHz >60
15p 10p 80kHz >60
For: RF = 33K, RI = 3.3K, RG = 22K
Table 1: Typical values for case where op amp effective gain = 1.
CF
RI
+15V RF +Vs
CCH
R CL
OP IN
AMP
OUT
VIN
COM PB58
COMP
–15V
CC R L
–Vs GAIN R G
Figure 2. Non-inverting composite amplifier.
SLEW RATE
The slew rate of the composite amplifier is equal to the slew
rate of the driver times the booster gain, with a maximum value
equal to the booster slew rate.
OUTPUT SWING
The maximum output voltage swing required from the driver
op amp is equal to the maximum output swing from the booster
divided by the booster gain. The Vos of the booster must also
be supplied by the driver, and should be subtracted from the
available swing range of the driver. Note also that effects of
Vos drift and booster gain accuracy should be considered
when calculating maximum available driver swing.
AThPiEs XdatMa IshCeRetOhTaEsCbHeeNn OcaLreOfuGllYy cCheOcRkePdOanRdAiTs IbOelNieved t5o9b8e0relNiaOblRe,ThHowSeHveAr,NnNo OreNspoRnOsiAbiDlityisTaUssCumSOedNf,orApRosIsZibOleNiAnac8c5ur7ac4i1es or oUmSiAssionsA. APlPl sLpIeCciAfiTcaItOioNnSs aHreOsuTbLjIecNtEto: c1ha(n8ge00w)ith5ou4t6n-o2ti7c3e.9
PB58U REV. H JANUARY 1998 © 1998 Apex Microtechnology Corp.

4페이지












구       성 총 4 페이지수
다운로드[ PB58A.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PB58

POWER BOOSTER AMPLIFIERS

ETC
ETC
PB58A

POWER BOOSTER AMPLIFIERS

ETC
ETC

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵