Datasheet.kr   

PCA8521 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 PCA8521은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 PCA8521 자료 제공

부품번호 PCA8521 기능
기능 Infrared remote control transmitter RC5
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


PCA8521 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 20 페이지수

미리보기를 사용할 수 없습니다

PCA8521 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
DATA SHEET
PCA8521
Infrared remote control transmitter
RC5
Product specification
Supersedes data of 1997 Jul 03
File under Integrated Circuits, IC02
1999 Jun 15




PCA8521 pdf, 반도체, 판매, 대치품
Philips Semiconductors
Infrared remote control transmitter RC5
Product specification
PCA8521
PINNING
16-pin dual in-line and small outline package
SYMBOL
XTAL1
XTAL2
SN0
SN1
SN2
SN3
SN4
SN5
DR4
DR3
DR2
DR1
DR0
VSS
LOUT
VDD
PIN DESCRIPTION
1 oscillator input
2 oscillator output
3 sense line 0 for key matrix
4 sense line 1 for key matrix
5 sense line 2 for key matrix
6 sense line 3 for key matrix
7 sense line 4 for key matrix
8 sense line 5 for key matrix
9 drive line 4 for key matrix
(active LOW)
10 drive line 3 for key matrix
(active LOW)
11 drive line 2 for key matrix
(active LOW)
12 drive line 1 for key matrix
(active LOW)
13 drive line 0 for key matrix
(active LOW)
14 ground
15 output signal (active LOW)
16 power supply
handbook, halfpage
XTAL1 1
16 VDD
XTAL2 2
15 LOUT
SN0 3
14 VSS
SN1 4
SN2 5
13 DR0
PCA8521
12 DR1
SN3 6
11 DR2
SN4 7
10 DR3
SN5 8
9 DR4
MBH032
Fig.2 Pin configuration (DIP/SO16).
1999 Jun 15
4

4페이지










PCA8521 전자부품, 판매, 대치품
Philips Semiconductors
Infrared remote control transmitter RC5
Product specification
PCA8521
Timing generator
A schematic diagram of the timing generator is illustrated
in Fig.4. The oscillator frequency is 432 kHz or 4 MHz.
The timing generator is stopped when no key is activated
and started again when a key is pressed.
The output of the oscillator (CLK1) is divided by 111 for
4 MHz or by 12 for 432 kHz. Selection is achieved using a
mask option. The output of the divider is CLK2 which is
used for clocking of the control timer. The frequency of
CLK2 is 36 kHz and the inverse is used to generate the
output pulses in the subcarrier frequency. By mask option
the duty factor can be chosen to be 25% or 33%.
The control timer has a length of 4096 subcarrier (pulse)
periods. This is equal to the transmission repetition time.
A bit time is equal to 64 pulses and the repetition time is
64 bit times. The control timer provides the timing of the
key scanning, the ROM access and the code transmission.
When the control timer has arrived at a certain state, and
no key has been pressed for at least 28 ms, a stop signal
will be generated which will stop the oscillator. All drive
lines will then be set to logic 0. As soon as a key is pressed
one of the sense lines will become logic 0. This will
generate a start signal which will restart the oscillator.
Key scanning
Six bits of the control timer are used to control the key
scanning, subsequently 64 time slots are available. Each
time slot corresponds to a key number. The 3 most
significant bits (MSBs) control the drive lines and the
3 least significant bits (LSBs) control the sense lines.
The scan timing is illustrated in Fig.5. In the first 8 time
slots drive line DR0 is LOW. During this time the 8 sense
lines SN0 to SN7 are sequentially tested. The same
occurs for the next 8 time slots when DR1 is at logic 0 and
so on until DR6 is at logic 0. After testing there are 8 time
slots when no drive line is at logic 0 (all drive lines HIGH).
When, during time slots 0 to 63, one of the sense lines is
at logic 0 the contents of the 6 bits is stored in the key
register. This register is used to address the ROM.
No transmission will take place when two or more keys are
activated. This situation is considered to be the same as
‘no key’ and the control bit in the command word for the
next transmission will be toggled.
When no key is pressed the oscillator will stop at the end
of the control timer (see Section “Timing generator”).
In this situation all drive lines will be set to logic 0. When
one of the keys is pressed again a wake-up will occur by
starting the oscillator.
An option is available to select ‘single’ or ‘multi’ system.
Single system
SN0 should be connected to one of the drive lines or
ground.
The bank that will be selected is equal to drive line number
to which SN0 is connected. When connected to ground the
number will be 7. This is achieved by loading the bank
select flip-flops BS0 to BS2 with the contents of C5 to C7
of the control timer (see Fig.4) when sense line SN0 is at
logic 0. In this way it is possible to use two different
systems in one transmitter by using a side switch. With this
option SN0 cannot be used to connect keys, so the
maximum number of keys will be lower. (49 keys with
20-pin IC and 25 keys with 16-pin IC).
Multi system
The bank is selected by key for maximum 8 different
systems (e.g. TV, VCR, CD, etc.), any key is flexible for
bank selection. When a user inserts a new battery, the
default bank is always in bank 7. If only bank 7 is used,
then maximum number of keys can be:
56 keys for a 20-pin IC
30 keys for 16-pin IC.
ROM
A schematic diagram of the ROM is illustrated in Fig.6.
The ROM is divided into 8 banks of 2 × 64 bytes. Bank
selection is performed using flip-flops BS0 to BS2 that are
the 3 highest bits of the address. With the ‘single system’
these bits are loaded from the 3 MSBs of the scan control
when SN0 = 0. At power-on the bank select flip-flops will
be in an arbitrary state.
When a key was activated, the key number is stored in the
6-bit key register. This register forms the lower bits of the
ROM address. For each command the ROM will be
accessed twice. This gives 16 bits in total (M0L to M7L
and M0H to M7H). The bits are described in Table 3.
1999 Jun 15
7

7페이지


구       성 총 20 페이지수
다운로드[ PCA8521.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PCA8521

Infrared remote control transmitter RC5

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵