Datasheet.kr   

PCA9514D 데이터시트 PDF




Integrated Circuit Systems에서 제조한 전자 부품 PCA9514D은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PCA9514D 자료 제공

부품번호 PCA9514D 기능
기능 Hot swappable IC and SMBus bus buffer
제조업체 Integrated Circuit Systems
로고 Integrated Circuit Systems 로고


PCA9514D 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 20 페이지수

미리보기를 사용할 수 없습니다

PCA9514D 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
PCA9513; PCA9514
Hot swappable I2C and SMBus bus buffer
Product data sheet
Supersedes data of 2004 Jan 07
2004 Oct 05
Philips
Semiconductors




PCA9514D pdf, 반도체, 판매, 대치품
Philips Semiconductors
Hot swappable I2C and SMBus bus buffer
Product data sheet
PCA9513; PCA9514
TYPICAL APPLICATION — PCA9513
VCC
(2.7 V to
5.5 V)
SCLIN
8
3
C1
0.01 µF R5
10 k
R3
10 k
2
R4
10 k
SDAIN
67
ENABLE
BLOCK DIAGRAM — PCA9513
1
ENABLE
5
READY
GND
4
Figure 2. Typical application — PCA9513
OVERVOLTAGE
CUTOFF
SDAIN 6
92 mA
SLEW RATE
DETECTOR
CONNECT
2 mA
BACKPLANE-TO-CARD
CONNECTION
PCA9513
2 mA
SLEW RATE
DETECTOR
CONNECT
SCLOUT
SDAOUT
SW02158
8 VCC
7 SDAOUT
OVERVOLTAGE
CUTOFF
SCLIN 3
92 mA
SLEW RATE
DETECTOR
CONNECT
2 mA
BACKPLANE-TO-CARD
CONNECTION
2 mA
SLEW RATE
DETECTOR
CONNECT
2 SCLOUT
0.55VCC/
0.45VCC
0.55VCC/
0.45VCC
UVLO
ENABLE 1
130 µs
DELAY
2004 Oct 05
STOP BIT AND
BUS IDLE
0.5 µA
20 pF
UVLO
0.5 pF
Figure 3. Block diagram — PCA9513
4
CONNECT
RD
QB
S
5 READY
4 GND
CONNECT
SW02159

4페이지










PCA9514D 전자부품, 판매, 대치품
Philips Semiconductors
Hot swappable I2C and SMBus bus buffer
Product data sheet
PCA9513; PCA9514
Propagation Delays
The delay for a rising edge is determined by the combined pull-up
current from the bus resistors and the rise time accelerator current
source and the effective capacitance on the lines. If the pull-up
currents are the same, any difference in rise time is directly
proportional to the difference in capacitance between the two sides.
The tPLH may be negative if the output capacitance is less than the
input capacitance and would be positive if the output capacitance is
larger than the input capacitance, when the currents are the same.
The tPHL can never be negative because the output does not start to
fall until the input is below 0.7VCC, and the output turn on has a non
zero delay, and the output has a limited maximum slew rate, and
even if the input slew rate is slow enough that the output catches up
it will still lag the falling voltage of the input by the offset voltage. The
maximum tPHL occurs when the input is driven LOW with zero delay
and the output is still limited by its turn on delay and the falling edge
slew rate. The output falling edge slew rate is a function of the
internal maximum slew rate which is a function of temperature, VCC,
and process, as well as the load current and the load capacitance.
Rise Time Accelerators
During positive bus transitions a 2 mA current source is switched on
to quickly slew the SDA and SCL lines HIGH once the input level of
0.8 V for the PCA9513 and PCA9514 are exceeded. The rising edge
rate should be at least 1.25 V/µs to guarantee turn on of the
accelerators. The 0.8 V threshold of PCA9513 and PCA9514 allows
for larger bounce-or-noise without falsely triggering the rise time
accelerators.
READY Digital Output
This pin provides a digital flag which is LOW when either ENABLE is
LOW or the start-up sequence described earlier in this section has
not been completed. READY goes HIGH when ENABLE is HIGH
and start-up is complete. The pin is driven by an open drain
pull-down capable of sinking 3 mA while holding 0.4 V on the pin.
Connect a resistor of 10 kto VCC to provide the pull-up.
ENABLE Low Current Disable
Grounding the ENABLE pin disconnects the backplane side from the
card side, disables the rise-time accelerators, drives READY LOW,
disables the bus precharge circuitry, and puts the part in a LOW
current state. When the pin voltage is driven all the way to VCC, the
part waits for data transactions on both the backplane and card
sides to be complete before reconnecting the two sides.
Resistor Pull-up Value Selection
The system pull-up resistors must be strong enough to provide a
positive slew rate of 1.25 V/µs on the SDA and SCL pins, in order to
activate the boost pull-up currents during rising edges. Choose
maximum resistor value using the formula:
R v 800 @ 103
VCC(MIN) * 0.6
C
where R is the pull-up resistor value in , VCC(MIN) is the
minimum VCC voltage in volts and C is the equivalent bus
capacitance in picofarads (pF).
In addition, regardless of the bus capacitance, always choose R
16 kfor VCC = 5.5 V maximum, R 24 kfor VCC = 3.6 V
maximum. The start-up circuitry requires logic high voltages on
SDAOUT and SCLOUT to connect the backplane to the card, and
these pull-up values are needed to overcome the precharge voltage
(PCA9511 only). See the curves in Figures 7 and 8 for guidance in
resistor pull-up selection.
RPULLUP
(k)
30
25
20
RMAX = 24 k
15
RISE-TIME > 300 ns
21
RECOMMENDED
PULL-UP
5
0
0 100
200 300
400
CBUS (pF)
SW02115
Figure 7. Bus requirements for 3.3 V systems
20
RPULLUP
(k)
15
21
5
RMAX = 16 k
RISE-TIME
> 300 ns
RECOMMENDED
PULL-UP
0
0 100
200 300
400
CBUS (pF)
SW02116
Figure 8. Bus requirements for 5 V systems
Minimum SDA and SCL Capacitance Requirements
The device connection circuitry requires a minimum capacitance
loading on the SDA and SCL pins in order to function properly. The
value of this capacitance is a function of VCC and the bus pull-up
resistance. Estimate the bus capacitance on both the backplane and
the card data and clock buses, and refer to Figures 7 and 8 to
choose appropriate pull-up resistor values. Note from the figures
that 5 V systems should have at least 47 pF capacitance on their
buses and 3.3 V systems should have at least 22 pF capacitance for
proper operation. Although the device has been designed to be
marginally stable with smaller capacitance loads, for applications
with less capacitance, provisions need to be made to add a
capacitor to ground to ensure these minimum capacitance
conditions if oscillations are noticed during initial signal integrity
verification.
2004 Oct 05
7

7페이지


구       성 총 20 페이지수
다운로드[ PCA9514D.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PCA9514A

Hot swappable I2C-bus and SMBus bus buffer

NXP Semiconductors
NXP Semiconductors
PCA9514D

Hot swappable IC and SMBus bus buffer

Integrated Circuit Systems
Integrated Circuit Systems

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵