|
|
|
부품번호 | PCA9515D 기능 |
|
|
기능 | I2C-bus repeater | ||
제조업체 | NXP Semiconductors | ||
로고 | |||
전체 11 페이지수
INTEGRATED CIRCUITS
PCA9515
I2C-bus repeater
Product data sheet
Supersedes data of 2003 Nov 10
Philips
Semiconductors
2004 Jun 24
Philips Semiconductors
I2C-bus repeater
Product data sheet
PCA9515
APPLICATION INFORMATION
A typical application is shown in Figure 3. In this example, the
system master is running on a 3.3 V I2C-bus while the slave is
connected to a 5 V bus. Both buses run at 100 kHz unless the slave
bus is isolated and then the master bus can run at 400 kHz. Master
devices can be placed on either bus.
3.3 V
5V
SDA
SCL
BUS
MASTER
400 kHz
SDA0 SDA1
SCL0 SCL1
PCA9515
EN
BUS0
SDA
SCL
SLAVE
100 kHz
BUS1
SW00867
Figure 3. Typical application
The PCA9515 is 5 V tolerant so it does not require any additional
circuitry to translate between the different bus voltages.
When one side of the PCA9515 is pulled LOW by a device on the
I2C-bus, a CMOS hysteresis type input detects the falling edge and
causes an internal driver on the other side to turn on, thus causing
the other side to also go LOW. The side driven LOW by the
PCA9515 will typically be at VOL = 0.5 V.
In order to illustrate what would be seen in a typical application, refer
to Figures 4 and 5. If the bus master in Figure 3 were to write to the
slave through the PCA9515, we would see the waveform shown in
Figure 4 on Bus 0. This looks like a normal I2C transmission until the
falling edge of the 8th clock pulse. At that point, the master releases
the data line (SDA) while the slave pulls it LOW through the
PCA9515. Because the VOL of the PCA9515 is typically around
0.5 V, a step in the SDA will be seen. After the master has
transmitted the 9th clock pulse, the slave releases the data line.
9th CLOCK PULSE
2 V/DIV
VOL OF MASTER
Figure 4. Bus 0 waveform
VOL OF PCA9515
SW00866
2004 Jun 24
4
4페이지 Philips Semiconductors
I2C-bus repeater
Product data sheet
PCA9515
AC ELECTRICAL CHARACTERISTICS — PCA9515
SYMBOL
PARAMETER
TEST CONDITIONS
MIN.
LIMITS
TYP.
MAX.
UNIT
tPHL Propagation delay
Waveform 1
57 98 170 ns
tPLH Propagation delay
Waveform 1
33 55 78 ns
tTHL Transition time
Waveform 1
— 67 — ns
tTLH Transition time
Waveform 1; Note 1
— 135 — ns
tSET Enable to Start condition
100 —
— ns
tHOLD
Enable after Stop condition
100 —
— ns
NOTE:
1. The tTLH transition time is specified with loads of 1.35 kΩ pull-up resistance and 7 pF load capacitance, plus an additional 50 pF load
capacitance. Different load resistance and capacitance will alter the RC time constant, thereby changing the propagation delay and
transition times.
AC WAVEFORMS
INPUT
1.5 V
tPHL
OUTPUT
80%
tTHL
1.5 V
20%
3.3 V
1.5 V
0.1 V
1.5 V
20%
tPLH
80%
3.3 V
tTLH
VOL
Waveform 1.
SW00646
TEST CIRCUIT
PULSE
GENERATOR
VIN
RT
VCC
VCC
D.U.T.
VOUT
RL
CL
Test Circuit for Open Drain Outputs
DEFINITIONS
RL = Load resistor; 1.35 kΩ
CL = Load capacitance includes jig and probe capacitance;
7 pF
RT = Termination resistance should be equal to ZOUT of
pulse generators.
SW00792
2004 Jun 24
7
7페이지 | |||
구 성 | 총 11 페이지수 | ||
다운로드 | [ PCA9515D.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
PCA9515 | I2C-bus repeater | NXP Semiconductors |
PCA9515A | PCA9515A Dual Bidirectional I2C Bus and SMBus Repeater (Rev. D) | Texas Instruments |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |