Datasheet.kr   

PCB2421 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 PCB2421은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PCB2421 자료 제공

부품번호 PCB2421 기능
기능 1K dual mode serial EEPROM
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


PCB2421 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 24 페이지수

미리보기를 사용할 수 없습니다

PCB2421 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
DATA SHEET
PCB2421
1K dual mode serial EEPROM
Preliminary specification
Supersedes data of 1995 Oct 11
File under Integrated Circuits, IC12
1997 Apr 01




PCB2421 pdf, 반도체, 판매, 대치품
Philips Semiconductors
1K dual mode serial EEPROM
Preliminary specification
PCB2421
4 BLOCK DIAGRAM
book, full pagewidth
VSS VDD
48
WP
SDA
SCL
VCLK
3
5
6 I/O
CONTROL
7 LOGIC
MEMORY
CONTROL
LOGIC
X
DECODER
HV GENERATOR
EEPROM
ARRAY
PAGE LATCHES
n.c.
TEST(1)
2
1
PCB2421
Y
DECODER
SENSE AMPLIFIER
R/W CONTROL
(1) Factory use only.
Fig.1 Block diagram.
MBG271
5 PINNING
SYMBOL PIN
DESCRIPTION
TEST
1 factory use only: must be tied to VDD;
may not be left open-circuit
n.c. 2 may be tied to VSS, VDD, or left
open-circuit
WP 3 write protect input (LOW = write
protected, HIGH = not write protected);
may not be left open-circuit
VSS
SDA
4 ground
5 serial data input/output
SCL 6 serial clock input/output (DDC2B)
VCLK
7 serial clock input (transmit-only mode,
DDC1)
VDD 8 supply voltage
handbook, halfpage
TEST 1
n.c. 2
WP 3
VSS 4
8 VDD
7 VCLK
PCB2421
6 SCL
5 SDA
MBG272
Fig.2 Pin configuration.
1997 Apr 01
4

4페이지










PCB2421 전자부품, 판매, 대치품
Philips Semiconductors
1K dual mode serial EEPROM
Preliminary specification
PCB2421
Table 2 Mode configurations
DDC
DCC1
DCC2
WP
X(1)
1
0
Note
1. Where X = don’t care.
MODE
R
R/W
R
6.7 Read operation
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the slave
address is set to logic 1. There are three basic types of
read operations: current address read, random read, and
sequential read.
6.7.1 CURRENT ADDRESS READ
The PCB2421 contains an address counter that maintains
the address of the last word accessed, internally
incremented by one. Therefore, if the previous access
(either a read or write operation) was to address ‘n’, the
next current address read operation would access data
from address n + 1. Upon receipt of the slave address with
R/W set to logic 1, the PCB2421 issues an acknowledge
and transmits the eight bit data word. The master will not
acknowledge the transfer but does generate a STOP
condition and the PCB2421 discontinues transmission
(see Fig.10).
6.7.2 RANDOM READ
Random read operations allow the master to access any
memory location in a random manner. To perform this type
of read operation, the word address must first be set. This
is done by sending the word address to the PCB2421 as
part of a normal write operation. After the word address is
sent, the master generates a REPEATED START
condition following the acknowledge. This terminates the
write operation, but not before the internal address pointer
is set. The master then issues the control byte again but
with the R/W bit set to logic 1. The PCB2421 will then issue
an acknowledge and transmits the 8-bit data word.
The master will not acknowledge the transfer but does
generate a STOP condition and the PCB2421
discontinues transmission (see Fig.11).
6.7.3 SEQUENTIAL READ
Sequential reads are initiated in the same way as a
random read except that after the PCB2421 transmits the
first data byte, the master issues an acknowledge as
opposed to a STOP condition in a random read.
This directs the PCB2421 to transmit the next sequentially
addressed 8-bit word. To provide sequential reads the
PCB2421 contains an internal address pointer which is
incremented by one at the completion of each operation.
This address pointer allows the entire memory contents to
be serially read during one operation.
6.8 Pin description
6.8.1 SDA
This pin is used to transfer addresses and data into and
out of the device, when the device is in the bidirectional
(I2C-bus, DDC2B) mode. In the transmit-only mode
(DDC1), which only allows data to be read from the device,
data is also transferred on the SDA pin. This pin is an
open-drain terminal, therefore the SDA bus requires a
pull-up resistor connected to VDD (typically 10 kfor
100 kHz). See brochure “The I2C-bus and how to use it”
(order no. 9398 393 40011) or “Data Handbook IC12”.
6.8.2 SCL
This pin is the clock input for the bidirectional mode
(I2C-bus, DDC2B), and is used to synchronize data
transfer to and from the device. It is also used as the
signalling input to switch the device from the transmit-only
mode to the bidirectional mode. It must remain HIGH for
the chip to continue operation in the transmit-only mode
(DDC1).
6.8.3 VCLK
This pin is the clock input for the transmit-only mode
(DDC1). In the transmit-only mode, each bit is clocked out
on the rising edge of this signal. In DDC2B mode, this input
is a don’t care.
6.8.4 WP
This pin is used to inhibit writing of the EEPROM. When
this pin is connected to ground, writing of the EEPROM is
inhibited. When connected to VDD (and VCLK = VDD), the
EEPROM can be programmed. WP may not be left
open-circuit. WP input is a ‘don’t care’ in DDC1 mode.
6.8.5 TEST
Pins 1 is a TEST pin for factory use only. It must be
connected to VDD in the application.
6.8.6 N.C.
This pin has no connection and may be tied to VSS, VDD or
left open-circuit.
1997 Apr 01
7

7페이지


구       성 총 24 페이지수
다운로드[ PCB2421.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PCB2421

1K dual mode serial EEPROM

NXP Semiconductors
NXP Semiconductors
PCB2421P

1K dual mode serial EEPROM

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵