|
|
PDF AQY212GH Data sheet ( Hoja de datos )
| Número de pieza | AQY212GH | |
| Descripción | PhotoMOS RELAYS | |
| Fabricantes | Etc | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AQY212GH (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
GU (General Use) Type
1-Channel (Form A)
High Capacity 4-Pin Type
cUL VDE
pending pending
PhotoMOS
RELAYS
4.78
.188
1
6.4
.252
3.2
.126
4
mm inch
FEATURES
1. Greatly increased load current.
2. Reinforced insulation 5,000 V type.
3. Greatly improved specs allow you to
use this in place of mercury and
mechanical relays.
4. Compact 4-pin DIP size.
TYPICAL APPLICATIONS
• Security market
(use in I/O for alarm and security devices,
etc.)
• Measuring instrument market
23
TYPES
Type
I/O isolation
voltage
Output rating*
Load Load
voltage current
Through hole
terminal
Tube packing style
Part No.
Surface-mount terminal
Tape and reel packing style
Picked from the Picked from the
1/2-pin side 3/4-pin side
Packing quantity
Tube
Tape and reel
AC/DC Reinforced
type 5,000 V
60 V
1.1 A
AQY212GH
AQY212GHA
AQY212GHAX
AQY212GHAZ
1 tube contains
100 pcs.
1 batch contains
1,000 pcs.
1,000 pcs.
*Indicate the peak AC and DC values.
Note: For space reasons, the initial letters of the product number “AQY”, the SMD terminal shape indicator “A” and the package type indicator "X" and
"Z" are omitted from the seal.
RATING
1. Absolute maximum ratings (Ambient temperature: 25°C 77°F)
Item
Symbol
AQY212GH
LED forward current
IF
50 mA
Input
LED reverse voltage
Peak forward current
VR
IFP
5V
1A
Power dissipation
Pin
75 mW
Load voltage (peak AC)
VL
60 V
Output
Continuous load current
(peak AC)
Peak load current
IL
Ipeak
1.1 A
3.0 A
Power dissipation
Pout
500 mW
Total power dissipation
PT 550 mW
I/O isolation voltage
Viso 5,000 V AC
Operating
Temperature limits
Storage
Topr –40°C to +85°C –40°F to +185°F
Tstg –40°C to +100°C –40°F to +212°F
Remarks
f = 100 Hz, Duty factor = 0.1%
100ms (1 shot), VL = DC
Non-condensing at low temperatures
1 page  
Cautions for Use
SAFETY WARNINGS
• Do not use the product under conditions
that exceed the range of its specifications.
It may cause overheating, smoke, or fire.
• Do not touch the recharging unit while
the power is on. There is a danger of
electrical shock. Be sure to turn off the
power when performing mounting,
maintenance, or repair operations on the
relay (including connecting parts such as
the terminal board and socket).
AQY212GH
• Check the connection diagrams in the
catalog and be sure to connect the
terminals correctly. Erroneous
connections could lead to unexpected
operating errors, overheating, or fire.
NOTES
1. Short across terminals
Do not short circuit between terminals
when relay is energized. There is
possibility of breaking the internal IC.
2. Surge voltages at the input
If reverse surge voltages are present at
the input terminals, connect a diode in
reverse parallel across the input terminals
and keep the reverse voltages below the
reverse breakdown voltage.
14
23
3. Recommended LED forward current
(IF)
It is recommended that the LED forward
current (IF) be kept at 5mA.
4. Ripple in the input power supply
If ripple is present in the input power
supply, observe the following:
1) For LED operate current at Emin,
maintain the value mentioned in the table
of “Note 3. Recommended LED forward
current (IF).”
2) Keep the LED operate current at 50
mA or less at Emax.
Emin.
Emax.
5. Output spike voltages
1) If an inductive load generates spike
voltages which exceed the absolute
maximum rating, the spike voltage must
be limited.
Typical circuits are shown below.
14
Load
23
Add a clamp diode
to the load
14
Load
23
Add a CR snubber
circuit to the load
2) If spike voltages generated at the load
are limited with a clamp diode and the
circuit wires are long, spike voltages will
occur by inductance. Keep wires as short
as possible to minimize inductance.
6. Cleaning solvents compatibility
Dip cleaning with an organic solvent is
recommended for removal of solder flux,
dust, etc. Select a cleaning solvent from
the following table. If ultrasonic cleaning is
used, the severity of factors such as
frequency, output power and cleaning
solvent selected may cause loose wires
and other defects. Make sure these
conditions are correct before use. For
details, please consult us.
Cleaning solvent
Compatibility
(r: Yes !: No)
Chlorine- • Trichlene
base
• Chloroethlene
r
• Indusco
Adueous • Hollis
• Lonco Terg
r
Alcohol- • IPA
base
• Ethanol
r
Others
• Thinner
• Gasoline
!
7. Soldering
1) When soldering PC board terminals,
keep soldering time to within 10 s at
260°C 500°F.
(1) IR (Infrared reflow) soldering method
T3
T2
T1
2) When soldering surface-mount
terminals, the following conditions are
recommended.
(2) Vapor phase soldering method
T2
T1
(3) Double wave soldering method
T2
T1
t1 t2
T1 = 155 to 165°C 311 to 329°F
T2 = 180°C 200°C 356 to 392°F
T3 = 245°C 473°F or less
t1 = 120 s or less
t2 = 30 s or less
(4) Soldering iron method
Tip temperature: 280 to 300°C 536 to
572°F
Wattage: 30 to 60 W
Soldering time: within 5 s
t1 t2
T1 = 180 to 200°C 366 to 392°F
T2 = 215°C 419°F or less
t1 = 40 s
t2 = 90 s or less
t1 t2 t3
T1 = 155 to 165°C 311 to 329°F
T2 = 260°C 500°F or less
t1 = 60 s or less
t2+t3 = 5 s or less
(5) Others
Check mounting conditions before using
other soldering methods (hot-air, hot
plate, pulse heater, etc.)
• The temperature profile indicates the
temperature of the soldered terminal on
the surface of the PC board. The ambient
temperature may increase excessively.
Check the temperature under mounting
conditions.
• The conditions for the infrared reflow
soldering apply when preheating using
the VPS method.
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet AQY212GH.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AQY212GH | PhotoMOS RELAYS | Etc |
| AQY212GHA | PhotoMOS RELAYS | Etc |
| AQY212GHAX | PhotoMOS RELAYS | Etc |
| AQY212GHAZ | PhotoMOS RELAYS | Etc |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |