Datasheet.kr   

PDIUSBH12N 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 PDIUSBH12N은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PDIUSBH12N 자료 제공

부품번호 PDIUSBH12N 기능
기능 USB 2-port hub
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


PDIUSBH12N 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 28 페이지수

미리보기를 사용할 수 없습니다

PDIUSBH12N 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
PDIUSBH12
USB 2-port hub
Product specification
Supersedes data of 1999 Feb 25
Philips
Semiconductors
1999 Jul 22




PDIUSBH12N pdf, 반도체, 판매, 대치품
Philips Semiconductors
USB 2-port hub
Product specification
PDIUSBH12
Analog Transceivers
These transceivers interface directly to the USB cables through
some termination resistors. They are capable of transmitting and
receiving serial data at both “full speed” (12 Mbit/s) and “low speed”
(1.5 Mbit/s) data rates.
Hub Repeater
The hub repeater is responsible for managing connectivity on a per
packet basis. It implements packet signaling connectivity and
resume connectivity.
Low speed devices can be connected to downstream ports since the
repeater will not propagate upstream packets to downstream ports,
to which low speed devices are connected, unless they are
preceded by a PREAMBLE PID.
End of Frame Timers
This block contains the specified EOF1 and EOF2 timers which are
used to detect loss-of-activity and babble error conditions in the hub
repeater. The timers also maintain the low-speed keep-alive strobe
which is sent at the beginning of a frame.
General and Individual Port Controller
The general and individual port controllers together provide status
and control of individual downstream ports. Via the I2C-interface a
microcontroller can access the downstream ports and request or
change the status of each individual port.
Any change in the status or settings of the individual port will result
in an interrupt request. Via an interrupt register, the servicing
microcontroller can look up the downstream port which generated
the interrupt and request its new status. Any port status change can
then be reported to the host via the hub status change (interrupt)
endpoint.
PLL
A 12 MHz to 48 MHz clock multiplier PLL (Phase-Locked Loop) is
integrated on-chip. This allows for the use of low-cost 12 MHz
crystal. EMI is also minimized due to lower frequency crystal. No
external components are needed for the operation of the PLL.
Bit Clock Recovery
The bit clock recovery circuit recovers the clock from the incoming
USB data stream using 4X over-sampling principle. It is able to track
jitter and frequency drift specified by the USB specification.
Philips Serial Interface Engine (PSIE)
The Philips SIE implements the full USB protocol layer. It is
completely hardwired for speed and needs no firmware intervention.
The functions of this block include: synchronization pattern
recognition, parallel/serial conversion, bit stuffing/de-stuffing, CRC
checking/generation, PID verification/generation, address
recognition, handshake evaluation/generation.
Memory Management Unit (MMU) and Integrated
RAM
The MMU and the integrated RAM is used to handle the large
difference in data rate between USB, running in bursts of 12 Mbit/s
and the I2C interface to the microcontroller, running at up to
1 Mbit/s. This allows the microcontroller to read and write USB
packets at its own speed through I2C.
I2C Slave Interface
This block implements the necessary I2C interface protocol. A slave
I2C allows for simple micro-coding. An interrupt is used to alert the
microcontroller whenever the PDIUSBH12 needs attention. As a
slave I2C device, the PDIUSBH12 I2C clock: SCL is an input and is
controlled by the microcontroller. The I2C interface can run up to 1
Mbit/s.
SoftConnect
The connection to the USB is accomplished by bringing D+ (for
high-speed USB device) high through a 1.5 kpull-up resistor. In
the PDIUSBH12, the 1.5 kpull-up resistor is integrated on-chip
and is not connected to VCC by default. Similarly, the 15 k
pull-down resistors are integrated on-chip and are not connected to
GND by default. The connection of the internal resistors to Vcc is
established through a command sent by the external/system
microcontroller. This allows the system microcontroller to complete
its initialization sequence before deciding to establish connection to
the USB. Re-initialization of the USB bus connection can also be
affected without requiring the pull out of the cable.
The PDIUSBH12 will check for USB VBUS availability before the
connection can be established. VBUS sensing is provided through
OCURRENT_N pin. See the pin description for details. Sharing of
VBUS sensing and overcurrent sensing can be easily accomplished
by using VBUS voltage as the pull-up voltage for the open drain
output of the overcurrent indication device.
It should be noted that the tolerance of the internal resistors is
higher (30%) than that specified by the USB specification (5%).
However, the overall VSE voltage specification for the connection
can still be met with good margin. The decision to make use of this
feature lies with the users.
SoftConnectis a patent pending technology from Philips
Semiconductors.
GoodLink
Good downstream USB connection indication is provided through
GoodLinktechnology. When the port is enabled and there is at
least one valid upstream traffic from the port, the LED indicator will
be ON. The LED indicator will blink on every valid upstream traffic. A
valid upstream traffic is defined as traffic with a good SOP and
terminated by a good EOP. During global suspend, all LEDs will be
OFF.
This feature provides a user-friendly indicator on the status of the
hub, the connected downstream devices and the USB traffic. It is a
useful field diagnostics tool to isolate the faulty equipment. This
feature helps lower the field support and the hotline costs.
1999 Jul 22
4

4페이지










PDIUSBH12N 전자부품, 판매, 대치품
Philips Semiconductors
USB 2-port hub
Product specification
PDIUSBH12
Pin description (MODE 0 – Good Link)
PIN NO. PIN SYMBOL
TYPE DRIVE
1 TEST1
Input
2 TEST2
3 TEST3
4 RESET_N
5 GND
6 XTAL1
7 XTAL2
8 CLKOUT
9 VCC
Input
Input
Input
Power
Input
Output
Output
Power
ST
3mA
10 OCURRENT_N Input
ST
11 SWITCH_N
Output
OD6
12 SUSPEND
Output
OD6
13 DN2_GL_N
Output
OD6
14 DN3_GL_N
Output
OD6
15 RSVD
Input
16 RSVD
Input
17 INT_N
Output
OD6
18 SDA
I/O OD6
19 SCL
I/O OD6
20 GND
Power
21 DN3_DP
AI/O
22 DN3_DM
AI/O
23 DN2_DP
AI/O
24 DN2_DM
AI/O
25 AGND
Power
26 AVCC
27 UP_DP
Power
AI/O
28 UP_DM
AI/O
NOTE:
1. Signals ending in _N indicate active low signals.
ST: Schmitt Trigger
OD6: Open Drain with 6 mA drive
AI/O: Analog I/O
DESCRIPTION
Connect to Ground for 48MHz crystal input.
Connect to VCC for 12MHz crystal input.
Connect to Ground
Connect to Ground
Power-on reset
Ground reference
Crystal connection 1 (48 or 12MHz depending on TEST1 pin)
Crystal connection 2 (48 or 12MHz depending on TEST1 pin)
Programmable output clock for external devices
Voltage supply 3.3V ± 0.3V
Over-current notice to the device. This pin is also used to sense the USB VBUS.
A LOW on this pin of less than 2 seconds is interpreted as an overcurrent notice;
longer than 2 seconds is interpreted as loss of VBUS.
Enables power to downstream ports
Device is in suspended state
Downstream port 2 GoodLinkLED indicator
Downstream port 3 GoodLinkLED indicator
Reserved. Connect to GND for normal operation.
Reserved. Connect to GND for normal operation.
Connect to microcontroller interrupt
I2C bi-directional data
I2C bit-clock
Ground reference
Downstream port 3 D+ connection
Downstream port 3 Dconnection
Downstream port 2 D+ connection
Downstream port 2 D- connection
Analog Ground reference
Analog voltage supply 3.3V ± 0.3V
Upstream D+ connection
Upstream D- connection
1999 Jul 22
7

7페이지


구       성 총 28 페이지수
다운로드[ PDIUSBH12N.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PDIUSBH12

USB 2-port hub

NXP Semiconductors
NXP Semiconductors
PDIUSBH12D

USB 2-port hub

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵