|
|
PDF MBT35200MT1 Data sheet ( Hoja de datos )
| Número de pieza | MBT35200MT1 | |
| Descripción | High Current Surface Mount PNP Silicon Switching Transistor for Load Management in Portable Applications | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MBT35200MT1 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
MBT35200MT1
High Current Surface
Mount PNP Silicon
Switching Transistor for
Load Management in
Portable Applications
A Device of the mX™ Family
MAXIMUM RATINGS (TA = 25°C)
Rating
Collector-Emitter Voltage
Collector-Base Voltage
Emitter-Base Voltage
Collector Current — Continuous
Collector Current — Peak
Electrostatic Discharge
Symbol
VCEO
VCBO
VEBO
IC
ICM
ESD
THERMAL CHARACTERISTICS
Characteristic
Symbol
Total Device Dissipation
TA = 25°C
Derate above 25°C
PD (Note 1.)
Thermal Resistance,
Junction to Ambient
RθJA (Note 1.)
Total Device Dissipation
TA = 25°C
Derate above 25°C
PD (Note 2.)
Thermal Resistance,
Junction to Ambient
RθJA (Note 2.)
Thermal Resistance,
Junction to Lead #1
RθJL
Total Device Dissipation
(Single Pulse < 10 sec.)
PDsingle
(Notes 2. & 3.)
Junction and Storage
Temperature Range
TJ, Tstg
1. FR–4 @ Minimum Pad
2. FR–4 @ 1.0 X 1.0 inch Pad
3. ref: Figure 9
Max Unit
–35 Vdc
–55 Vdc
–5.0 Vdc
–2.0 Adc
–5.0 A
HBM Class 3
MM Class C
Max Unit
625 mW
5.0 mW/°C
200 °C/W
1.0 W
8.0 mW/°C
120 °C/W
80 °C/W
1.75 W
–55 to
+150
°C
http://onsemi.com
35 VOLTS
2.0 AMPS
PNP TRANSISTOR
COLLECTOR
1, 2, 5, 6
3
BASE
4
EMITTER
32 1
4
56
CASE 318G
TSOP
STYLE 6
DEVICE MARKING
G4 (date code)
ORDERING INFORMATION
Device
Package
Shipping
MBT35200MT1 Case 318G 3000/Tape & Reel
© Semiconductor Components Industries, LLC, 2000
August, 2000 – Rev. 1
1
Publication Order Number:
MBT35200MT1/D
1 page  
MBT35200MT1
INFORMATION FOR USING THE TSOP–6 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the
total design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.094
2.4
0.037
0.95
0.074
1.9
0.037
0.95
0.039
1.0
TSOP–6
0.028
0.7
inches
mm
TSOP–6 POWER DISSIPATION
The power dissipation of the TSOP–6 is a function of the
drain pad size. This can vary from the minimum pad size
for soldering to a pad size given for maximum power
dissipation. Power dissipation for a surface mount device is
determined by TJ(max), the maximum rated junction
temperature of the die, RθJA, the thermal resistance from
the device junction to ambient, and the operating
temperature, TA. Using the values provided on the data
sheet for the TSOP–6 package, PD can be calculated as
follows:
PD =
TJ(max) – TA
RθJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25°C,
one can calculate the power dissipation of the device which
in this case is 625 milliwatts.
PD =
150°C – 25°C
200°C/W
= 625 milliwatts
The 200°C/W for the TSOP–6 package assumes the use
of the recommended footprint on a glass epoxy printed
circuit board to achieve a power dissipation of
625 milliwatts. There are other alternatives to achieving
higher power dissipation from the TSOP–6 package.
Another alternative would be to use a ceramic substrate or
an aluminum core board such as Thermal Clad™. Using a
board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
• Always preheat the device.
• The delta temperature between the preheat and
soldering should be 100°C or less.*
• When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10°C.
• The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
• When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
• After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
• Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause
excessive thermal shock and stress which can result in
damage to the device.
http://onsemi.com
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet MBT35200MT1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MBT35200MT1 | High Current Surface Mount PNP Silicon Switching Transistor for Load Management in Portable Applications | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |