|
|
|
부품번호 | MC7900ACD2T 기능 |
|
|
기능 | THREE-TERMINAL NEGATIVE FIXED VOLTAGE REGULATORS | ||
제조업체 | ON | ||
로고 | |||
MC7900 Series
1.0 A Negative Voltage
Regulators
The MC7900 series of fixed output negative voltage regulators are
intended as complements to the popular MC7800 series devices.
These negative regulators are available in the same seven−voltage
options as the MC7800 devices. In addition, one extra voltage option
commonly employed in MECL systems is also available in the
negative MC7900 series.
Available in fixed output voltage options from − 5.0 V to − 24 V,
these regulators employ current limiting, thermal shutdown, and
safe−area compensation − making them remarkably rugged under
most operating conditions. With adequate heatsinking they can deliver
output currents in excess of 1.0 A.
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe−Area Compensation
• Available in 2% Voltage Tolerance (See Ordering Information)
• Pb−Free Package May be Available. The G−Suffix Denotes a
Pb−Free Lead Finish
2.0 k 8.0 k
Gnd
www.DataSheet4U.com
3.6 k 1.0 k 4.0 k R1
1.2 k 1.6 k
R2
10 k
20 pF
10 pF 10 k
2.0 k 20 k 20 k
1.1 k
240
750
This device contains 26 active transistors.
VO
0.3
VI
Figure 1. Representative Schematic Diagram
http://onsemi.com
TO−220
T SUFFIX
CASE 221AB
Heatsink surface
connected to Pin 2.
1
2
3
Pin 1. Ground
2. Input
3. Output
D2PAK
D2T SUFFIX
CASE 936
12
3
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
STANDARD APPLICATION
Input
Cin*
0.33 mF
MC79XX
Output
CO**
1.0 mF
A common ground is required between the input
and the output voltages. The input voltage must
remain typically 2.0 V above more negative even
during the high point of the input ripple voltage.
XX, These two digits of the type number
indicate nominal voltage.
** Cin is required if regulator is located an
appreciable distance from power supply filter.
** CO improve stability and transient response.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 14
1
Publication Order Number:
MC7900/D
MC7900 Series
MC7906C
ELECTRICAL CHARACTERISTICS (VI = −11 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 3)
(TJ = +25°C, IO = 100 mA)
−8.0 Vdc ≥ VI ≥ − 25 Vdc
−9.0 Vdc ≥ VI ≥ −13 Vdc
(TJ = +25°C, IO = 500 mA)
−8.0 Vdc ≥ VI ≥ − 25 Vdc
−9.0 Vdc ≥ VI ≥ −13 Vdc
Load Regulation, TJ = +25°C (Note 3)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
VO
Regline
Regload
− 5.75
−
−
−
−
−
−
− 6.0
9.0
3.0
43
10
13
5.0
− 6.25
60
30
120
60
120
60
Vdc
mV
mV
Output Voltage
−8.0 Vdc ≥ VI ≥ − 21 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO Vdc
−5.7 − −6.3
Input Bias Current (TJ = +25°C)
Input Bias Current Change
−8.0 Vdc ≥ VI ≥ − 25 Vdc
5.0 mA ≤ IO ≤ 1.5 A
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Ripple Rejection (IO = 20 mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 A, 0°C ≤ TJ ≤ +125°C
IIB − 4.3 8.0 mA
DIIB mA
− − 1.3
− − 0.5
Vn − 45 − mV
RR − 65 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7908C
ELECTRICAL CHARACTERISTICS (VI = −14 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 3)
(TJ = +25°C, IO = 100 mA)
−10.5 Vdc ≥ VI ≥ −25 Vdc
−11 Vdc ≥ VI ≥ −17 Vdc
(TJ = +25°C, IO = 500 mA)
−10.5 Vdc ≥ VI ≥ −25 Vdc
−11 Vdc ≥ VI ≥ −17 Vdc
Load Regulation, TJ = +25°C (Note 3)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
VO
Regline
Regload
−7.7
−
−
−
−
−
−
−8.0 −8.3
12 80
5.0 40
50 160
22 80
26 160
9.0 80
Vdc
mV
mV
Output Voltage
−10.5 Vdc ≥ VI ≥ − 23 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO Vdc
−7.6 − −8.4
Input Bias Current (TJ = +25°C)
IIB − 4.3 8.0 mA
Input Bias Current Change
−10.5 Vdc ≥ VI ≥ − 25 Vdc
5.0 mA ≤ IO ≤ 1.5 A
DIIB mA
− − 1.0
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn − 52 − mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 62 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C
DVO/DT
mV/°C
− −1.0 −
3. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
http://onsemi.com
4
4페이지 MC7900 Series
MC7918C
ELECTRICAL CHARACTERISTICS (VI = − 27 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 6)
(TJ = +25°C, IO = 100 mA)
−21 Vdc ≥ VI ≥ − 33 Vdc
−24 Vdc ≥ VI ≥ − 30 Vdc
(TJ = +25°C, IO = 500 mA)
−21 Vdc ≥ VI ≥ − 33 Vdc
−24 Vdc ≥ VI ≥ − 30 Vdc
Load Regulation, TJ = +25°C (Note 6)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
VO −17.3 −18 −18.7 Vdc
Regline
mV
− 25 180
− 10 90
− 90 360
− 50 180
Regload
mV
− 110 360
− 55 180
Output Voltage
−21 Vdc ≥ VI ≥ − 33 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO Vdc
−17.1 − −18.9
Input Bias Current (TJ = +25°C)
Input Bias Current Change
−21 Vdc ≥ VI ≥ − 33 Vdc
5.0 mA ≤ IO ≤ 1.5 A
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Ripple Rejection (IO = 20 mA, f = 120 Hz)
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C
IIB − 4.5 8.0 mA
DIIB mA
− − 1.0
− − 0.5
Vn
− 110 −
mV
RR − 59 − dB
VI−VO − 1.3 − Vdc
DVO/DT
mV/°C
− −1.0 −
MC7924B, MC7924C
ELECTRICAL CHARACTERISTICS (VI = − 33 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.)
Characteristics
Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C)
Line Regulation (Note 6)
(TJ = +25°C, IO = 100 mA)
−27 Vdc ≥ VI ≥ − 38 Vdc
−30 Vdc ≥ VI ≥ − 36 Vdc
(TJ = +25°C, IO = 500 mA)
−27 Vdc ≥ VI ≥ − 38 Vdc
−30 Vdc ≥ VI ≥ − 36 Vdc
Load Regulation, TJ = +25°C (Note 6)
5.0 mA ≤ IO ≤ 1.5 A
250 mA ≤ IO ≤ 750 mA
VO −23 −24 −25 Vdc
Regline
mV
− 31 240
− 14 120
− 118 470
− 70 240
Regload
mV
− 150 480
− 85 240
Output Voltage
−27 Vdc ≥ VI ≥ − 38 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W
VO Vdc
−22.8 − −25.2
Input Bias Current (TJ = +25°C)
IIB − 4.6 8.0 mA
Input Bias Current Change
−27 Vdc ≥ VI ≥ − 38 Vdc
5.0 mA ≤ IO ≤ 1.5 A
DIIB mA
− − 1.0
− − 0.5
Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn
− 170 −
mV
Ripple Rejection (IO = 20 mA, f = 120 Hz)
RR − 56 − dB
Dropout Voltage (IO = 1.0 A, TJ = +25°C)
VI−VO − 1.3 − Vdc
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C
DVO/DT
mV/°C
− −1.0 −
6. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
*Tlow = −40°C for MC7924B and Tlow = 0°C for MC7924C.
http://onsemi.com
7
7페이지 | |||
구 성 | 총 16 페이지수 | ||
다운로드 | [ MC7900ACD2T.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
MC7900ACD2T | THREE-TERMINAL NEGATIVE FIXED VOLTAGE REGULATORS | ON |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |