|
|
|
부품번호 | NL10276AC30-01 기능 |
|
|
기능 | 38 cm 15 inches / 1024 x 768 pixels / Full-color / Multi-scan Function / Built-in backlight with inverter Ultra wide viewing angle | ||
제조업체 | NEC | ||
로고 | |||
DATA SHEET
TFT COLOR LCD MODULE
NL10276AC30-01A
38 cm (15 inches), 1024 × 768 pixels, Full-color,
Multi-scan Function, Built-in backlight with inverter
Ultra wide viewing angle
DESCRIPTION
www.DataSheet4U.coNmL10276AC30-01A is a TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising
amorphous silicon TFT attached to each signal electrode, a driving circuit, a CRT interface board and a backlight.
NL10276AC30-01A has a built-in backlight with an inverter.
The 38cm (15” inches) diagonal display area contains 1024 × 768 pixels and can display full-color (more than 16
million colors simultaneously). Also, it has ultra-wide viewing angle and multi-scan function. Therefore, this module
calls Super Fine TFT.
CRT interface board installed in this module allows you to achieve the LCD monitor with an analog RGB
interface.
FEATURES
• Ultra wide viewing angle
• Multi-scan function
• e.g. XGA, SVGA, VGA, VGA-TEXT, PC-
9801, MAC
• High luminance
• Incorporated edge type backlight (Four
lamps into two lamp holders, Inverter)
• Lamp holder replaceable (Part No. 150LHS01)
• On Screen Display
• CRT interface board
• Auto recognition of input signal
Analog RGB signals, Sync on green, Synchronous
signals (HS, Vsync, Composite)
• Digital control: e.g. Brightness, Display position, Contrast,
CLK delay
• Free supply voltage sequence
• Corresponding to DDC1 and DDC2B
• Corresponding to VESA DPMS
Regarding the use of OSD, please note that there is possibility of conflicts with a patent in Europe and the U.S.
Thus, if such conflict might happen when you use OSD, we shall not be resposible for any trouble.
VESA : Video Electronics Standards Association
DPMS : Display Power Management Signaling
DDC1 : Display Data Channel 1
DDC2B : Display Data Channel 2B
APPLICATIONS
• Engineering workstation (EWS), Desk-top type of PC
The information in this document is subject to change without notice.
Document No. EN0417EJ1V0DS00 (1st edition)
Date Published January 1999 P
Printed in Japan
©
1999
NL10276AC30-01A
GENERAL SPECIFICATIONS
Item
Module size
Display area
Number of dots
Pixel pitch
Dot pitch
Pixel arrangement
Display colors
www.DataSheet4U.cWomeight
Contents
350.0 ± 0.6 (H) × 265.0 ± 0.6 (V) × 24.0 (max.) (D)
304.128 (H) × 228.096 (V)
1024 × 3 (H) × 768 (V)
0.297 (H) × 0.297 (V)
0.099 (H) × 0.297 (V)
RGB (Red, Green, Blue) vertical stripe
Full color
1,480 (typ.), 1600 (max.)
ABSOLUTE MAXIMUM RATINGS
Parameter
Supply voltage
Logic input voltage
R, G, B input voltage
CLK input voltage
Storage temp.
Operating temp.
Humidity
(no condensation)
Symbol
Rating
Unit
VDD –0.3 to + 14
V
VDDB
–0.3 to + 14
V
VIN1 –0.3 to + 5.5
V
VIN2 –6.0 to + 6.0
V
VIN3 –7.0 to + 7.0
V
TST –20 to + 60 °C
TOP 0 to 50
°C
≤ 95% relative humidity
≤ 85% relative humidity
Absolute humidity shall not exceed Ta = 50°C,
85% relative humidity level.
Remarks
Ta = 25°C
Ta = 25°C
VDD = 12 V
–
Module surface
Ta ≤ 40°C
40 < Ta ≤ 50°C
Ta > 50°C
Notes 1. Measured at the LCD panel (Include own fever)
2. No condensation
Unit
mm
mm
dots
mm
mm
–
color
g
Note 1
4 Data Sheet EN0417EJ1V0DS00
4페이지 NL10276AC30-01A
POWER SUPPLY SEQUENCE
There is no sequence among the synchronous signals, the video signals and the power supply. However, 12 V
for backlight should be started up within 80 ms, otherwise, the protection circuit makes the backlight turns off.
Please note that the supply voltage must not be applied while the control signals (SEL, UP, DOWN and RESET)
are connected to GND. Otherwise the module may cause malfunctions.
If the power supply voltage is applied while SEL and RESET is connected to GND, the mode is set into NEC
factory mode. In this case, both LEDON and LEDOFF become “H”. Please do not use the module in this mode
which may write over the default value. Please turn off the power supply immediately and turn on the power while
SEL and RESET are connected to GND again. If the default value has been revised by accident, please follow the
instruction below.
www.DataSheet4U.com
<NEC factory mode>
This mode can control Brightness and Contrast and OSD position. Factory Reset function is reset all values. But
do not use the module in this mode which may write over the default values affect to the LCD internal operation.
Please turn off the power immediately and turn on the power while SEL and RESET are connected to GND again.
If the default value has been revised by accident, please select “Factory Reset” mode and press “Reset” key for
over two seconds.
Functions
Brightness
Contrast
LCD Data
Color adjust
VCO
HDTV Select
OSD position
Factory Reset
RESET
Control contents
Total Brightness and Sub Brightness for each RGB
Total Contrast and Sub Contrast for each RGB
Never select and adjust values
Change the OSD display position
Above function values is reset to factory values.
RESET the NEC factory mode
How to reset
Press RESET key over 2 seconds
Press RESET key over 2 seconds
Please go to the Factory reset.
−
Press Reset key over 2 seconds.
−
Data Sheet EN0417EJ1V0DS00
7
7페이지 | |||
구 성 | 총 30 페이지수 | ||
다운로드 | [ NL10276AC30-01.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
NL10276AC30-01 | 38 cm 15 inches / 1024 x 768 pixels / Full-color / Multi-scan Function / Built-in backlight with inverter Ultra wide viewing angle | NEC |
NL10276AC30-01A | 38 cm 15 inches / 1024 x 768 pixels / Full-color / Multi-scan Function / Built-in backlight with inverter Ultra wide viewing angle | NEC |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |