Datasheet.kr   

TSA5518M 데이터시트 PDF




Philips에서 제조한 전자 부품 TSA5518M은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 TSA5518M 자료 제공

부품번호 TSA5518M 기능
기능 1.3 GHz bidirectional I2C-bus controlled synthesizer
제조업체 Philips
로고 Philips 로고


TSA5518M 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 20 페이지수

미리보기를 사용할 수 없습니다

TSA5518M 데이터시트, 핀배열, 회로
INTEGRATED CIRCUITS
DATA SHEET
TSA5518M
1.3 GHz bidirectional I2C-bus
controlled synthesizer
Product specification
File under Integrated Circuits, IC02
1997 Mar 07




TSA5518M pdf, 반도체, 판매, 대치품
Philips Semiconductors
1.3 GHz bidirectional I2C-bus controlled
synthesizer
Product specification
TSA5518M
PINNING
SYMBOL PIN
DESCRIPTION
UD 1 drive output (UD)
P7 2 P7 output port
P5 3 P5 output port
P4 4 P4 output port
BS 5 bandswitch output for M/O drive
n.c 6 not connected
RF2 7 UHF/VHF signal input 2
RF1 8 UHF/VHF signal input 1
GND
9 ground
P1 10 P1 output port (general purpose)
P0 11 P0 output port (general purpose)
AS 12 input for Address Selection
P6 13 P6 port (output/input for general
purpose ADC)
P2
SDA
SCL
14 P2 output port (fDIV if the test mode
is active)
15 I2C-bus serial data input/output
16 I2C-bus serial clock
VCC 17 voltage supply
n.c 18 not connected
XTAL
19 crystal oscillator input
PD 20 charge-pump output (PD)
handbook, halfpage
UD 1
20 PD
P7 2
19 XTAL
P5 3
18 n.c.
P4 4
17 VCC
BS 5
16 SCL
TSA5518M
n.c. 6
15 SDA
RF2 7
14 P2
RF1 8
GND 9
P1 10
13 P6
12 AS
11 P0
MBH947
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
The device is controlled via the two wire I2C-bus.
For programming, there is one module address (7 bits)
and the R/W bit for selecting READ or WRITE mode.
Write mode
The write data format is summarized in Table 1. After the
address transmission (first byte), data bytes can be sent to
the device. Four data bytes are needed to fully program
the device. The bus transceiver has an auto increment
facility which permits the programming of the device within
one single transmission (address byte + 4 data bytes).
The device can also be partially programmed on the
condition that the first data byte following the address is
byte 2 or 4. The meaning of the bits in the data bytes is
given in Table 3. The first bit of the first data byte
transmitted indicates whether frequency data (first bit = 0)
or charge pump and port information (first bit = 1) will
follow. Until an I2C-bus STOP condition is sent by the
controller, additional data bytes can be entered without the
need to re-address the device. This allows a smooth
frequency sweep for fine tuning or AFC purpose. At
power-on the ports are set to the high-impedance state
(open-collector outputs) or at the HIGH level (emitter
follower outputs). The bandswitch output BS provides a
voltage output suitable for the band selection input of
mixer/oscillator ICs TDA5330, TDA5630A and TDA5730.
It is controlled by B1 and B0 bits or P7, P5 and P4 bits
depending on the BSC bit (see Tables 1 to 4). The
7.8125 kHz reference frequency is obtained by dividing
the output of the 4 MHz crystal oscillator by 512. Because
the input of UHF/VHF signal is first divided-by-8 the step
size is 62.5 kHz. A 3.2 MHz crystal can offer step size of
50 kHz.
1997 Mar 07
4

4페이지










TSA5518M 전자부품, 판매, 대치품
Philips Semiconductors
1.3 GHz bidirectional I2C-bus controlled
synthesizer
Product specification
TSA5518M
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
VCC
Vi(XTAL)
Vi(SCL)
VSDA
Vi(AS)
Vo(BS)
Vi(RF)
Vo
VPD
VUD
ISDA
Io
Tstg
Tj(max)
tsc(GND)(max)
tsc(VCC)(max)
PARAMETER
supply voltage
voltage at pin XTAL
voltage at pin SCL
voltage at pin SDA
voltage at pin AS
voltage at pin BS
voltage at pins RF1 and RF2
output voltage at ports P0, P2
and P6
output voltage at ports P4, P5
and P7
output voltage at pin PD
output voltage at pin UD
output current at pin SDA
output current at pins P0, P1
and P2
output current at pins P4, P5
and P7
output current at pin P6
storage temperature
maximum junction temperature
maximum short circuit time to
GND
maximum short circuit time to
VCC
CONDITIONS
open collector
emitter follower
open collector
one pin to GND (VCC = 5.5 V;
GND = 0 V)
one pin to VCC (VCC = 5.5 V; GND = 0 V)
MIN.
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
1
1
1
1
40
MAX.
+6
+VCC
+6
+6
+VCC
+VCC
+VCC
+16
UNIT
V
V
V
V
V
V
V
V
+VCC V
+VCC
+VCC
+5
+20
V
V
mA
mA
+10 mA
+10
+150
150
10
mA
°C
°C
s
10 s
HANDLING
Every pin withstands the ESD test in accordance with MIL-STD-833C category B (2000 V).
Every pin withstands the ESD test in accordance with Philips Semiconductor machine model 0 , 200 pF.
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
Rth j-a
thermal resistance from junction to ambient
CONDITIONS
in free air
VALUE
120
UNIT
K/W
1997 Mar 07
7

7페이지


구       성 총 20 페이지수
다운로드[ TSA5518M.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
TSA5518M

1.3 GHz bidirectional I2C-bus controlled synthesizer

Philips
Philips

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵