|
|
|
부품번호 | S7600A 기능 |
|
|
기능 | TCP/IP Network Protocol LSI | ||
제조업체 | Seiko | ||
로고 | |||
전체 30 페이지수
S-7600A TCP/IP NETWORK PROTOCOL STACK LSI Revision 1.2
Hardware Specification
S-7600A
TCP/IP Network Protocol LSI
Seiko Instruments USA Inc.
Phone +1-909-934-9334
Fax +1-909-975-5699
2990 West Lomita Boulevard
Torrance, California 90505
Seiko Instruments Inc.
S-7600A
Hardware Specification
LIST OF FIGURES
FIGURE 2.-1 BLOCK DIAGRAM ..................................................................................................................... 3
FIGURE 3.-1 PIN ASSIGNMENT .................................................................................................................... 4
FIGURE 3.-2 PACKAGE DIMENSIONS ........................................................................................................... 5
FIGURE 3.-3 CONFIGURATION OF EACH PIN ................................................................................................. 7
FIGURE 5.-4 68 FAMILY MPU WRITE TIMING ............................................................................................ 11
FIGURE 5.-5 68 FAMILY MPU READ TIMING.............................................................................................. 12
FIGURE 5.-6 X80 FAMILY MPU WRITE CYCLE TIMING .............................................................................. 13
FIGURE 5.-7 X80 FAMILY MPU READ CYCLE TIMING ................................................................................ 14
FIGURE 5.-8 SERIAL INTERFACE WRITE TIMING......................................................................................... 15
FIGURE 5.-9 SERIAL INTERFACE READ TIMING ......................................................................................... 16
FIGURE 5.-1 INT1 INTERRUPT TIMING ....................................................................................................... 17
FIGURE 6.-1 MEMORY INTERFACE ARCHITECTURE.................................................................................... 18
FIGURE 8.-1 SERIAL DATA FORMAT ......................................................................................................... 43
FIGURE 9.-1 HARDWARE RESET TIMING..................................................................................................... 45
FIGURE 9.-2 SOFTWARE RESET TIMING .................................................................................................... 45
FIGURE 10.-1 EXAMPLE FOR X80 FAMILY MPU ......................................................................................... 46
FIGURE 10.-2 EXAMPLE FOR 68K FAMILY MPU ......................................................................................... 47
FIGURE 10.-3 EXAMPLE FOR SERIAL INTERFACE........................................................................................ 48
iii Seiko Instruments Inc.
4페이지 S-7600A
Hardware Specification
1. Introduction
1.1. Product Overview
The S-7600A is a LSI that integrates TCP/IP network stack. It offers your devices a quicker and easier
connectivity to a network with its on-chip serial interface and a static RAM that operates as a buffer.
Implementing this LSI into your system can significantly reduce your software development cost. Also
its low operating frequency gives benefits to the power consumption.
The S-7600A also supports a microprocessor interface via the iReady iAPITM register set, and
connection to Physical Transport Layer Interface. iAPI consists of a set of register and operating
definitions that allow any micro controller system to interface with the internal modules.
1.2. Features
Industry standard protocols support :
TCP/IP (Ver. 4.0)
PPP (STD-51-compliant)
UDP
General purpose sockets :
Configured for two sockets
MPU interface :
68k/x80(MOTO/Intel) bus interface or Synchronous serial interface
Physical Transport Layer Interface :
Universal Asynchronous Receiver/Transmitter (UART)
Low clock rate :
Multiplied four by the bit-rate
Operating frequency :
256kHz typical
Low power consumption :
Full-transmitting Operating current consumption : 0.9mA typ.
Non-transmitting Operating current consumption : 150µA typ.
Standby current consumption : 1.0µA typ.
Stand-by mode :
held by RESET signal
Wide operating voltage range :
2.4V to 3.6V
Easier application development :
portable iAPITM support
1.3. Benefits
Off-loads MIPS allowing system to operate with low end and low cost processors.
Consumes minimal power-up to 1/100 of competing solution.
Seiko Instruments Inc.
1
7페이지 | |||
구 성 | 총 30 페이지수 | ||
다운로드 | [ S7600A.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
S7600A | TCP/IP Network Protocol LSI | Seiko |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |