Datasheet.kr   

UC3886 데이터시트 PDF




Unitrode에서 제조한 전자 부품 UC3886은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 UC3886 자료 제공

부품번호 UC3886 기능
기능 Average Current Mode PWM Controller IC
제조업체 Unitrode
로고 Unitrode 로고


UC3886 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 8 페이지수

미리보기를 사용할 수 없습니다

UC3886 데이터시트, 핀배열, 회로
Average Current Mode PWM Controller IC
UC1886
UC2886
UC3886
FEATURES
10.3V - 20V Operating Range
Low Offset Voltage Amplifier
High Bandwidth Current and Voltage
Amplifiers
Low Offset Current Sense Amplifier
Undervoltage Lockout
Trimmed 5 Volt Reference
Externally Programmable Oscillator
Charge Current
1.5A Peak Totem Pole Output
Available in 16-pin DIL or SOIC
Packages
BLOCK DIAGRAM
DESCRIPTION
The UC3886 family of PWM controller ICs is designed for DC-to-DC con-
verters with average current mode control. It is designed for use in con-
junction with the UC3910 4-bit DAC and Voltage Monitor. The UC3886
drives an external N-channel MOSFET and can be used to power the In-
tel Pentium® Pro and other high-end microprocessors.
The UC3886 in conjunction with the UC3910 converts 5VDC to an adjust-
able output ranging from 2.0V to 3.5V in 100mV steps with 35mV DC sys-
tem accuracy.
The oscillator is programmed by the user’s selection of an external resis-
tor and capacitor, and is designed for 300kHz typical operation.
The voltage and current amplifiers have 3.5MHz gain-bandwidth product
to satisfy high performance system requirements.
The internal current sense amplifier permits the use of a low value current
sense resistor, minimizing power loss. It has inputs and outputs accessi-
ble to allow user-selection of gain-setting resistors, and is internally com-
pensated for a gain of 5 and above. The command voltage input is
buffered and provided for use as the reference for the current sense am-
plifier.
The output of the voltage amplifier (input to the current amplifier) is
clamped to 1 volt above the command voltage to serve as a current limit.
The gate output can be disabled by bringing the CAO/ENBL pin to below
0.8 volts.
6/98
UDG-95098-2




UC3886 pdf, 반도체, 판매, 대치품
PIN DESCRIPTIONS
BUF: (Buffer Output) The voltage on COMMAND pin is
buffered and presented to the user here. This voltage is
used to provide the operating bias point for the current
sense amplifier by connecting a resistor between BUF
and ISP. Decouple BUF with 0.01µF or greater to SGND.
CAM: (Current Amplifier Minus Input) The average load
current feedback from ISO is typically applied through a
resistor here.
CAO/ENBL: (Current Amplifier Output/Chip Enable) The
current loop compensation network is connected be-
tween CAO/ENBL and CAM, the inverting input of the
current amplifier. The voltage at CAO/ENBL is the input
to the PWM comparator and regulates the output voltage
of the system. The GATE output is disabled (held low)
unless the voltage at this pin exceeds 1.0 volts, allowing
the PWM to force zero duty cycle when necessary. The
user can force this pin below 0.8 volts externally with an
open collector, disabling the GATE drive.
COMMAND: (Voltage Amplifier Non-Inverting Input) This
input to the voltage amplifier is connected to a command
voltage, such as the output of a DAC. This voltage sets
the switching regulator output voltage.
COMP: (Compensation, Voltage Amplifier Output) The
system voltage compensation network is applied be-
tween COMP and VSENSE. The voltage at COMP is
clamped to prevent it from going more than 1V above the
COMMAND voltage. This is used to provide an accurate
average current limit. The voltage on COMP is also
clamped to 0.7V below the voltage on COMMAND. This
is done to avoid applying a full charge to capacitors in
the compensation network during transients, allowing
quick recovery time and little overshoot.
CT: (Oscillator Timing Capacitor) A capacitor from CT to
SGND along with the resistor on RT, sets the PWM fre-
quency and maximum duty cycle according to these
formulas:
DMAX
= RT
V2. 0
mA4. 0
where DMAX is the maximum operating duty cycle, and
RT is in ohms.
( )FOSC
=
V2. 0 (4. 0mA RT) – 2. 0V
CT V1.8 RT mA4.0
where FOSC is the UC3886 oscillator switching fre-
quency in Hz, RT is in ohms, and CT is in farads.
UC1886
UC2886
UC3886
GATE: (PWM Output) The output is a 1A totem pole
driver. Use a series resistor of at least 5to prevent in-
teraction between the gate impedance and the output
driver that might cause excessive overshoot.
ISN: (Current Sense Amplifier Inverting Input) A resistor
to the low side of the average current sense resistor and
a resistor to ISO are applied to this pin to make a differ-
ential sensing amplifier.
ISO: (Current Sense Amplifier Output) A feedback resis-
tor to ISN is connected here to make a differential
sensing amplifier. The voltage at this pin is equal to
(VBUF + A • IAVG • RSENSE) where A is the user deter-
mined gain of the differential amplifier, IAVG is the
average load current of the system, and RSENSE is the
average current sensing resistor. For stability, A must be
greater than 5. Set A such that A • ISC • RSENSE = 1.0V
where ISC is the user-determined short circuit current
limit.
ISP: (Current Sense Amplifier Non-Inverting Input) A re-
sistor to the high side of the average current sense
resistor and a resistor to BUF are connected to this pin
to make a differential sensing amplifier.
PGND: (Power Ground) The PWM output current returns
to ground through this pin. This is separated from SGND
to avoid on-chip ground noise generated by the output
current.
RT: (Oscillator Charging Current) This pin is held at 2V.
Resistor RT from this pin to SGND sets the oscillator
charging current. Use 5k < RT < 100k.
SGND: (Signal Ground) For better noise immunity, sig-
nal ground is provided at this pin.
VCC: (Positive Supply Voltage) This pin supplies power
to the chip and to the gate drive output. Decouple to
PGND and separately to SGND for best noise immunity.
The reference (VREF), GATE output, oscillator, and am-
plifiers are disabled until VCC exceeds 10.3V.
VREF: (Voltage Reference Output) An accurate 5V refer-
ence as provided at this pin. The output can deliver 2mA
to external circuitry, and is internally short circuit current
limited. VREF is disabled if VCC is below UVLO. Bypass
5V REF to SGND with an 0.01µF or larger capacitor for
best stability.
VSENSE: (Voltage Sense Input) This input is connected
to COMP through a feedback network and to the power
supply output through a resistor or a divider network.
4

4페이지










UC3886 전자부품, 판매, 대치품
TYPICAL APPLICATIONS (cont.)
UC1886
UC2886
UC3886
Figure 8. UC3886 Configured with the UC3910 for a Pentium® Pro DC/DC Converter
UDG-96021
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
7

7페이지


구       성 총 8 페이지수
다운로드[ UC3886.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
UC3886

Average Current Mode PWM Controller IC

Unitrode
Unitrode
UC3886

Average Current Mode PWM Controller IC

Texas Instruments
Texas Instruments

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵